1 A beam is subjected to a moment of 972 k-ft. If the material the beam is made out of has a yield stress of 45ksi, what is the required section modulus for the beam to support the moment. Use elastic beam design principles. Submit your answer in in^3 with 2 decimal places. Type your answer... 2 A rectangular beam has a cross section that is 15mm wide and 22mm deep. If it is subjected to a shear load of 23.8 kN, what is the max shear stress in MPa? You may use reduced forms of the shear equation. Type your answer...

1 A beam is subjected to a moment of 972 k-ft. If the material the beam is made out of has a yield stress of 45ksi, what is the required section modulus for the beam to support the moment. Use elastic beam design principles. Submit your answer in in^3 with 2 decimal places. Type your answer... 2 A rectangular beam has a cross section that is 15mm wide and 22mm deep. If it is subjected to a shear load of 23.8 kN, what is the max shear stress in MPa? You may use reduced forms of the shear equation. Type your answer...

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Question 16 A simply-supported beam is supported beam is shown in Figure 6. Assume El is constant... Determine the slope and displacement at C using the method of virtual work. topp 2m 12 kN/m 3 m B
A 0.5kg weight is hung from the end of a cantilever beam, causing a vertical displacement of y = -0.01 inches relative to no load. The weight is increased to 1.0kg. What is the new displacement relative to no load? Typed and correct answer please. I ll rate
Find the largest normal and shear stress that will occur in the T-section beam given loading status.
Engr statics I check it was wrong answer 245.166 I need to show all work. Topic: Shear and Bending Moment A gantry crane of weight W-100 Kg moves across a bridge with the length 1-5 m. The front axle of the crane (which is nearer end A) carries 3/4W whereas the rear axle (nearer end B) carries 1/4 W. The distance of the axles is b = 1/20. Determine the maximum value of the bending moment and enter your answer in N-m units. Remember to also show all your work (FBDs, calculation steps, etc on the handworked file) HINT: Determine the shear and bending moment equations
Answer must 4 decimal place... NEED IN 30MINS ASAP
sovle the question given in the pic.
(a) The Figure la show the cross-section of a beam. All dimension are in cm. 10 2 10 Figure la (i) Calculate the centroid of the cross-section measured from the bottom of the cross section. (ii) Calculate the moment of inertia, I, for this cross-section. (iii)A pure bending moment of magnitude 1.0 kN.m is applied to the cross- section, generating compression above the neutral axis, and tension below. Calculate the maximum values of the tensile and compressive stress. (iv)The bending moment is removed. The same beam cross-section is now subject to a vertical shear force of 2.5 kN acting in the downward. Calculate the maximum horizontal shear stress. Where does it occur?
If the "I" value of beam cross section is 6,400,000 mm and the maximum distance from the neutral axis of the cross section to the top and bottom edges of the beam cross section is 139 mm, what is the section modulus of the beam? Note: Give your answer in mm3 Note: Do NOT include units in your answer. Answer:
For the beam shown in Fig. Determine the value of the 34mm distributed load W if the maximum shear stress is 30 2 m 2 m MPa. 800 mm 16 mm 125 mm 300 mm
Pls fast hand written solution
In the beam given with the section; a) Calculate the location and value of the maximum tensile and shear stresses that will occur alone. b) Is the beam tension according to the principal stresses and shear stress that you will calculate in the stress element to be taken around the neck point (E)? (σ) check = 2315 N / cm2, τemn = 1375 N / cm2
The beam shown will be constructed from a standard steel W-shape using an allowable bending stress of 40.4 ksi. Assume P = 51 kips, L1=6.6 ft, and L2=19.8 ft. (a) Determine the minimum section modulus required for this beam. (b) From the table below, select the lightest W shape that can be used for this beam. (c) What is the total weight of the steel beam itself (i.e., not including the loads that are carried by the beam)?