1-99 The force generated by a spring is given by F = kx, where k is the spring constant and x is the deflection of the spring. The spring of Fig. Pl–99 has a spring constant of 8 kN/cm. The pressures are P, = 5000 kPa, P2 = 10,000 kPa, and P, = 1000 kPa. If the piston diameters are D, = 8 cm and D, = 3 cm, how far will the spring be deflected? Answer: 1.72 cm

1-99 The force generated by a spring is given by F = kx, where k is the spring constant and x is the deflection of the spring. The spring of Fig. Pl–99 has a spring constant of 8 kN/cm. The pressures are P, = 5000 kPa, P2 = 10,000 kPa, and P, = 1000 kPa. If the piston diameters are D, = 8 cm and D, = 3 cm, how far will the spring be deflected? Answer: 1.72 cm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

3 12. Determine the absolute pressure at point B if the figure shown below if the density of mercury is 13 590 kg/m³ and that of water is 1000 kg//m³, gravitational acceleration is 9.80 m/s², Atmospheric pressure is 101 325 Pa A € H₂O B Atmosphere 510 mm A. 96.327 kPa B. 106. 323 kPa C. 169. 248 kPa D. 185.896 kPa 635 mm Hg
1 - 2 3 The rectangle above is a control volume. Flow 1 is 2.7 slugs/sec while flow 2 is 8.4 slugs/sec. The fluid has density 1.3 slugs/ft³. Determine the volumetric flow rate of flow 3 in ft³/sec. Answer with a positive number if the flow is out of the control volume and a negative number if the flow is into the control volume. Your answer should include at least one digit after the decimal place. Hint: Use continuity
30 N لة Box of mass 10 kg resting on rough horizontal surface. Find friction force and normal force if .coefficient of friction=0.17 10 N 60⁰° 6 N 20 N Normal force = 128 N and Friction Force = 21.77 N Normal force = 128 N and Friction Force = 41.77 N Normal force = 128 N and Friction Force =1.77 N O
Oil SG= 0.85
In mechanical fluid
mass should be kg, not N. Make your own assumption. I shall correct accordingly.
PLEASE ANSWER QUICKLY
ı need solution
For a gage pressure at B of -0.15 bar, find the relative density of the gage liquid A in the figure.
Mechanical Engineering The following equation is used to calculate a change in the kinetic energy of a moving mass: KE = 0.5 * m * (v2 - u2) Where the quantities are: the kinetic energy KE (in Joules), the mass m (in kg), the initial velocity u (in m/s) and the final velocity v (in m/s). Determine if the equation is dimensionally homogeneous or not.
B4
An automobile lift in the Karsha car wash and service station raises 5.6 kN car of 2.4 m above the floor level from the ground,As shown in the below given figure , If a hydraulic cylinder has a piston of diameter 234.5 cm . Find the following: (a) Necessary Work to lift the car vehicle (in J) (b) Required Pressure to lift the car.in pascal (c) Power needed to the raise the car in 0.8 minutes in kW