Determine Poisson's ratio if a cylindrical rod is placed in tension as shown and it is elastically deformed to extend 0.02 mm in its length and contracts 0.0003 mm in its diameter. Original dimensions of the cylinder: length 200 mm, diameter 10 mm. P Answers: (a) 0.2 (b) 0.3 (c) 0.4 (d) 0.5 P

Determine Poisson's ratio if a cylindrical rod is placed in tension as shown and it is elastically deformed to extend 0.02 mm in its length and contracts 0.0003 mm in its diameter. Original dimensions of the cylinder: length 200 mm, diameter 10 mm. P Answers: (a) 0.2 (b) 0.3 (c) 0.4 (d) 0.5 P

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1) The head H is connected to the cylinder of a compressor using six steel bolts. If the clamping force in each bolt is 4000N, determine the normal strain in the bolts. Each bolt has a diameter of 5 mm. If o₂ = 280 MPa and Est = 210GPa, what is the strain in each bolt when the nut is unscrewed so that the clamping force is released? a) 0.970 b) 0.203 c) 0.970(10-³) d) Insufficient information to determine because the stress is beyond yield point H &
IV. An Aluminum bar AD (see figure) has a cross-sectional area of 250 mm2 and is loaded by forces P1 = 7560 N, P2 = 5340 N, and P3 = 5780 N. The lengths of the segments of the bar are a = 1525 mm, b = 610 mm, and c = 910 mm. (a) Assuming that the modulus of elasticity is E = 72 GPa, calculate the change in length of the bar. Does the bar elongate or shorten? (b) By what amount P should the load P3 be increased so that the bar does not change in length when the three loads are applied? (c) If P3 remains at 5780 N, what revised cross-sectional area for segment AB will result in no change of length when all three loads are applied? A k a B₁ P₁ b C P₂ -P3
35 GPa, Gaum 28 The figure below shows a shaft of three segments It is restrained (fixed support) at both sides and is loaded by two torques. Use Gronze GPa and Gre= 83 GPa Steel diameter = 25 mm Bronze Aluminum diameter = 25 mm digmeter = 50 mm T-300 N.m T-700 N.m D 2 m 2 m 2.5 m Determine the relative angle of twist developec between bronze anc alumimu Select the correct response 0:511 rac 05 6 rad 0413 rad 0.005 rac
Q2/ A rectangular block of rubber is deformed as shown by the dotted line. Determine the average normal strain of line BD. Values shown are in mm. 450 A -4- B 300 C D 2.5
A 50 mm diameter cylindrical aluminum block is connected to 2 hollowed cylindrical steel blocks as shown in Figure. Both hollowed steel cylinders are of 60 mm and 40 mm outer and inner diameters respectively. The assembly is then connected to a rigid steel plate. Four bolts of diameter 10 mm are then used to rigidly fix the assembly to a wall. A force P is then applied to the assembly. The Modulus of elasticity(E) of steel is 200 GPa while aluminum has Modulus of elasticity(E) of 70 GPa. Both steel and aluminum have a yield strength (σy) of 250 MPa. The bolts have a yield stress (σy) of 800 MPa. All connections and joints are considered rigid.All lengths are in mm. a. Determine the allowable value of P that can be applied to the assembly taking into consideration theyielding of all parts of the assembly and bolts. Use a factor of safety of 1.5.b. Based on the value of P obtained part (a), determine the total elongation of the cylindrical steel block.c. Based on the value of P obtained…
Two rigid bars are connected with a rotationalspring, as shown in the figure. Assumethat the elastic rotational spring constant isβR = 75 kip-in./rad. Calculate the critical load Pcr ofthe system. Assume that L = 6 ft.
The assembly shown in Figure No. 3 consists of a hollow steel [E = 200 GPa] tube (1) with an outside diameter of 60 mm and a wall thickness of 5 mm, a solid 40 mm diameter aluminum [E= 70 GPa rod (2), and a solid 30 mm diameter aluminum rod (3). The member lengths are L1 2 000 mm, L2 = 1 200 mm, and L3 %D 3D800 mm. The following loads act on the assembly: P = 150 kN, Q = 80 kN, and R = 115 kN. Determine (a) the change in length of steel tube (1). (b) the deflection of joint D with respect to the fixed support at A.
X Your answer is incorrect. The pin-connected assembly consists of aluminum rods (1) and (2) and steel rod (3). The aluminum rods each have a diameter of 19 mm and an elastic modulus of E- 69 GPa. The steel rod has a diameter of 18 mm and an elastic modulus of E- 195 GPa. Assume a - 3.6 m, b - 1.5 m, and c- 0.8 m. What is the magnitude of load Pthat is necessary to displace point A 11 mm to the left? (3) A B Answer: P- i 73.7153 kN
A rigid beam rest on two bronze bars 700mm long. Another aluminum bar is placed between them which is 699.93mm long. If the weight of the beam is 375KN, determine the stress in the aluminum bar in MPa. (Round your answer to 3 decimal places) (Exclude your unit in the answer box)
The light rigid bar ABCD shown in the × figure is pinned at B and connected to two vertical rods. Assuming that the bar was initially horizontal and the rods stress-free and load P = 20 kips is applied. 4 ft Aluminum L = 4ft A = 0.75 in² E = 10 x 106 psi Steel L = 3ft A = 0.5 in² E = 29 x 106 psi k2A2A A. What is the stress experienced by aluminum rod B. What is the stress experienced by steel rod. C. What is the resulting deformation on the aluminum rod.
1 - An aluminum plate is subjected to uniform stress along its boundaries, as shown in the figure. Determine the change of length of diagonal BD. 120mm 120 MPa 160mm C B V 100MPa -200 MPa E-80GPa ✓=0.3 G=30MPa
A 50 mm diameter cylindrical aluminum block is connected to 2 hollowed cylindrical steel blocks as shown in Figure Q1. Both hollowed steel cylinders are of 60 mm and 40 mm outer and inner diameters respectively. The assembly is then connected to a rigid steel plate. Four bolts of diameter 10 mm are then used to rigidly fix the assembly to a wall. A force P is then applied to the assembly. The Modulus of elasticity(E) of steel is 200 GPa while aluminum has Modulus of elasticity(E) of 70 GPa. Both steel and aluminum have a yield strength(oy) of 250 MPa. The bolts have a yield stress (oy) of 800 MPa. All connections and joints are considered rigid. Q3 Determine the allowable value of P that can be applied to the assembly taking into consideration the yielding of all parts of the assembly and bolts. Use a factor of safety of 1.5. b. a. Based on the value of P obtained part (a), determine the total elongation of the cylindrical steel block. Based on the value of P obtained in part (a),…