02. A 1-0 half-wave rectifier is used to supply power to a load of impedance 82 from 220V, 50 Hz AC supply at a firing angle of 60°. The effective value of voltage is (a) 160 V (c) 140 V (b) 172 V (d) 120 V

02. A 1-0 half-wave rectifier is used to supply power to a load of impedance 82 from 220V, 50 Hz AC supply at a firing angle of 60°. The effective value of voltage is (a) 160 V (c) 140 V (b) 172 V (d) 120 V

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter12: Electronic Control Devices

Section: Chapter Questions

Problem 3RQ: Diodes and rectifiers allow current to _________. flow in one direction only flow in both...

See similar textbooks

Related questions

Q: If a half wave rectifier is supplied using 240 V (rms), 50 Hz supply, then using constant voltage…

A: average value of half wave rectifier is peak value of output voltageπ In half rectifier only one…

Q: What will be the out put of the D'Arsonval meters, if an average responding a.c meter of half-wave…

Q: A 3-phase, half-wave thyristor rectifier with an inductive load is supplied by a three-phase source…

A: Van=120 v phase voltage. firing angle= 40 3 phase Half wave Thyristor Rectifier.

Q: Find the average value of the full- wave rectifier if Vpeak = 20V a. 14.14V O b. 7.07V C. 12.73V O…

Q: Find the average value of the full- wave rectifier if Vpeak = 20V %3D a. 14.14V Ob. 7.07V • C.…

A: Given: For a full wave rectifier, The peak value is, Vp=20 V

Q: The RMS output voltage ofa Full-Wave Bridge Rectifier is 20 volts, Calculate the average current (in…

A: for full bridge rectifier RMS value of output voltage Vrms= Vm2…

Q: What should be the input peak voltage (in volts) in the given circuit below to produce a dc output…

Q: A three phase full wave rectifier is shown below. The input phase voltage peak is Vm=311.128 V. The…

A: Given Three phase full wave rectifier shown Vm=311.128 vThe load…

Q: i. Draw the rectifier circuit. i. Draw the input and the output voltages waveforms. un 2. i.…

Q: If the maximum value of applied voltage for a full-wave center Tap rectifier is 30 V, find the…

A: This is an easy problem on power electronics subject. The given maximum value of applied voltage is…

Q: Calculate the ripple voltage of a full-wave rectifier with a 75uF filter capacitor connected to a…

Q: (i) A single phase half wave controlled rectifier is operated from a 140 V, 50 Hz supply and the…

A: NOTE :- We’ll answer the first question since the exact one wasn’t specified. Please submit a new…

Q: When a 60 Hz sinusoidal voltage is applied to the input of a full-wave :rectifier, the output…

Q: A three phase bridge rectifier has a purely resistive load. The rectifier delivers 45 A current at…

A: In this question, choose the correct option What is rms voltage if average voltage = 300V

Q: If one of the diodes in a 60 Hz bridge full-wave rectifier opens, the output is Select one: a.…

Q: A three phase full wave rectifier is shown below. The input phase voltage peak is Vm=311.128 V. The…

A: The solution is given below the answer is option b

Q: The single-phase halt wave rectifier has a L= 6.5 mH, R = 0.5 2, and E = 10 V. The input voltage is…

A: It's given that : L=6.5mHR=0.5ΩE=10VVs=120VVm=1202f=60Hzα=60 or 1.047radian

Q: Question i. Show that the power factor for a controlled full-wave rectifier with a resistive load is…

A: As per policy, only attempting first question Circuit diagram for the controlled full wave rectifier…

Q: 89. If the ripple voltage in a full-wave rectifier is 25 V at a load current of 60 mA, its value at…

A: Given, For a full wave rectifier, Ripple voltage, V1=25 V Load current, IL1=60 mA For load current,…

Q: 72. If the input frequency to a 3-phase rectifier is 50 Hz, then output will have a frequency of (i)…

A: Given: Input frequency of a 3-phase rectifier, fin=50 Hz

Q: When a 92.83 Hz sinusoidal voltage is applied to the input of a full wave rectifier, the output…

A: Given, Input frequency for half wave rectifier, fiHWR=92.83 Hz Input frequency for full wave…

Q: Q-2: A singic phase full-wave controlled rectifier is connected to RL load (R-15 ohm an 1-20mH ).…

Q: 7-When a 60 Hz sinusoidal voltage is applied to the input of a half-wave rectifier, the output…

A: Disclaimer: Since you have asked multiple questions, we will solve the first question for you. If…

Q: 3: A single phase half wave controlled rectifier is used to supply power to a 20 Q load from a 230…

A: Rectifiers convert AC power to DC power whose average output voltages and currents are infinite.…

Q: Question 10 If a half wave rectifier is supplied using 240 V (rms), 50 Hz supply, then using…

A: The average output voltage of the half wave bridge rectifier.

Q: A single phase halfwave rectifier with an ac supply of 42V is used to charge a 12V battery through…

Q: A moving coil ammeter and a moving iron ammeter are connected in series with a rectifier across 110V…

Q: In the given Full Wave Center tapped Rectifier circuit, a step down transformer gives an RMS voltage…

A: As per Bartleby policy we can answer only three subparts. So I am solving first three for you.…

Q: If a half-wave rectifier is used with 117-V rms ac, the average dc output voltage is about: O 117 V…

A: Out put DC voltage of half wave rectifier is given as Vo=(Vm/π) Where Vm= maximum voltage Vm= √2…

Q: 4. If the load resistance of a capacitor-filtered full-wave rectifier is reduced, the ripple…

A: 4. Ripple voltage is directly proportional to load current and if load resistance will reduce then…

Q: For uncontrolled half wave rectifier, R=80ohm, L=0.15H, f=50Hz and Vm=311V. Find the point when the…

Q: The average output voltage for a single phase half wave rectifier for the input sine wave of…

A: The equation of sine wave is in the form Em sin ωt. Therefore, Em=200 Hence output voltage is Emπ.…

Q: 22. A single phase halfwave controlled rectifier has 400 sin 314 t as the input voltage and R as the…

Q: (i) A single phase fully controlled rectifier is operated from a 200 V, 50 Hz supply and the load…

A: Since we only answer one question at a time. we’ll answer the first question only.Please resubmit…

Q: What is the value of the ripple factor in a full-wave rectifier without filter? O 0.482 O 1.21 O…

A: Ripple factor is defined as the ratio of RMS value of the AC component of output to the average…

Q: A single phase full wave rectifier supplies a 20 Ohm load at an average voltage of 15 V. Determine…

A: Given: Single phase full wave rectifier Load, RL=20 Ω Average supplied voltage, Vavg=15 V

Q: For half wave rectifier circuit shown below Is = 5sin(wt), ripple factor = . Is Var Oa. 2.5 Ob. 1.21…

A: Ripple factor=ripple voltageAverage voltage. =(rms voltage)2-(Average…

Q: The half wave rectifier is supplied with 240V, 50Hz signal. Assume the number of turns in the…

A: We need to calculate the average dc current through load for a given half wave rectifier

Q: The half wave rectifier is supplied with 230V, 70HZ signal. Assume the number of turns in the…

A: The circuit given is a half-wave rectifier. Data given: Input voltage (Vin) = 230 V (RMS) frequency…

Q: If a resistive load is supplied from a single phase half wave rectifier , if a supply voltage is…

A: The solution can be achieved as follows.

Q: If the load resistance of a capacitor-filtered full-wave rectifier is increased, the ripple voltage…

A: Ripple voltage for a full wave capacitor-filtered rectifier is :- Vripple = Vout/ 2frCRL i.e.…

Q: What should be the input peak voltage (in volts) in the given circuit below to produce a dc output…

A: Given, The circuit is, The required dc output voltage is 31 volts. The diode used is Germanium.

Q: A single-phase controlled rectifier bridge consists of one SCR and three diodes as shown in figure.…

A: First draw the output voltage waveform and than find the average output voltage. Using average…

Q: If the time period of output voltage of a 1-o bridge rectifier is 25/3 ms, then the supply frequency…

A: Given: Time period of output voltage waveform, T'=253 ms

Q: The Ripple factor of Full wave rectifier is for input of 60HZ, and RI=1k, C=8uF. (Attach the…

A: The Rectifier output contains AC components as well as the DC components. Ripple Factor : Ripple…

Q: 2. A full wave rectifier is used to convert 400 Hz ac todc Desin a full-wave rectifier power supply…

A: Full wave rectifier. Frequency 400Hz , average DC voltage =15V Load current =1A Design the full…

Q: i. Show that the power factor for a controlled full-wave rectifier with a resistive load is 1…

Q: What should be the input peak voltage (in volts) in the given circuit below to produce a dc output…

Q: single-phase half- wave controlled rectifier circuit with inductive load (L-0.1 and R=102) and the…

Question

02. A 1-0 half-wave rectifier is used to supply
power to a load of impedance 82 from
220V, 50 Hz AC supply at a firing angle of
60°. The effective value of voltage is
(a) 160 V
(c) 140 V
(b) 172 V
(d) 120 V

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Three Phase Controlled and Uncontrolled Rectifiers

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Diodes and rectifiers allow current to _________. flow in one direction only flow in both directions divide paths of flow none of the above
What is the difference between a diode and rectifier?
If a half wave rectifier is supplied using 240 V (rms), 50 Hz supply, then using constant voltage drop model, the average output voltage is equal to 152.79 V 108.04 V 107.8 V 76.17 V
A full-wave rectifier uses 2 diodes. The internal resistance of each diode is 20 02. The transformer RMS secondary voltage from centre tap to each end of the secondary is 50 V and the load resistance is 980 2. Mean load current will be
What is the value of the ripple factor in a full-wave rectifier without filter? O 0.482 O 1.21 O 1.79 O 2.05
In a bridge full wave rectifier, the input sine wave is 25sin(30nt). The output frequency will be Select one: a. 15Hz b. 30Hz c. 25Hz d. 45Hz
The input voltage of a single-phase full- wave diode rectifier is v= 100 sinwt Volts and the resistive load is R. The RMS output voltage equals:
Q5) The schematic circuit in PLECS for a single-phase rectifier is shown below, Q5) The schematic circuit in PLECS for a single-phase rectifier is shown below, Thyristor Crout Probe Pulse Generator VC, pulses Probe Scope Thy Orso v Joad O R: 1 The output voltage across R is depicted in 0.5 0.0- b) 0.2 0.0 d)
A 1 - ∅ full-wave rectifier is made by using thyristors. If the peak value of the sinusoidal input voltage is Vm and the value of the delay angle is 45 degree, find the average value of output voltage Select one: a. 0.65 VM b. 0.85 VM c. 0.45 VM d. 0.25 Vm
When a 76.20 Hz sinusoidal voltage is applied to the input of a full wave rectifier, the output frequency (in Hz)
In a half wave rectifier, the input sine wave is 200sin200 nt Volts. If load resistance is of 1k then the average DC power output of half wave rectifier is O 4.016 W O 5.016W O 3.25W O 6.25W O not all above
Question (2) A controlled half-wave rectifier has a 240 V rms 60Hz ac source, The load a is R=30 Ohm resistor (a) Determine the delay angle such that the average load current is 2.5A (b) Determine the power absorbed by the load (c) Determine the power factor.