0.8 mm

Q: 2000 1 45001 3100 N

A: given; force in x-direction(Fx)=-2000N (compressive)force in y-direction(Fy)=-4500N…

Q: бх Oy Txy στ Txy бу In the diagram above, σ = 100 MPa, σy = -27 MPa,, and Tzy = 40 MPa. Let each…

A:

Q: Design the smallest diameter of the solid shaft if its rotation is to produce 600 HP at 15…

A:

Q: -01 Por the assembly ahovn the allovable atreas in the 75-mm diameter rod BC is 80 MPa, and 50 MPa…

A: When a shaft is subjected to torque, shear stress produces in the shaft. The torsion equation is…

Q: The cylinder of a hydraulic ram supported at the open end is 200 mm internal diameter and is…

A:

Q: The drive shaft of the motor is made of a material having an allowable shear stress of τallow= 72…

A:

Q: a) the principal stress and planes and (b) the maximum in-plane shear stress, average stress and its…

A:

Q: Q4 An aluminium tube, 1.2 m long, has the semi-circular crossection shown in the fig. If the stress…

A: LA=Length of an Aluminum tube=1.2 mσS=Maximum shear stress=35 MPa=35×106 PaG=26 GPa=26×109…

Q: The crank is loaded by a single force F, = 200 lb which causes twisting and bending of the 1-in…

A:

Q: Problem No. 3. The compound shaft has the following properties: G in both Segment 1 Segment 1 pipe…

A:

Q: The d = 13-mm-diameter solid rod passes through a D = 18-mm-diameter hole in the support plate. When…

A: To find:  The maximum value of Pmax supported by structure. Given:  The diameter of rod is d=13 mm1…

Q: The object (W 1000 lb) is moving between positions G and H back and forth repeatedly. The bar AD is…

A: W=1000 lbSy=80 ksi=80×103 psiS'n=20 ksi=20×103 ksiN=2

Q: Determine the equivalent state of stress on an element at the same point which represents the…

A: According to the given dataWe need to findAverage normal stressMaximum in-plane shear…

Q: The d = 16-mm-diameter solid rod passes through a D = 21-mm-diameter hole in the support plate. When…

A:

Q: The d = 12-mm-diameter solid rod passes through a D = 17-mm-diameter hole in the support plate. When…

A:

Q: 5. The drive shaft AB of an automobile is to be designed as a thin-walled tube. The engine delivers…

A:

Q: The motor A delivers 7500 kW to the shaft at 3600 rev/min, of which 2500 kW is removed by gear B and…

A:

Q: At what angular velocity will the stress of the rotating steel ring equal 250 MPa if its mean radius…

A:

Q: If the temperature of the 85 mmmm diameter post CD is increased by 60 ⚫C, determine the force…

A:

Q: The bell-crank mechanism is in equilibrium for an applied load of F₁ = 18 kN applied at A. Assume a…

A: F1 = 18kN a = 290mm b = 170mm c = 70mm and theta θ = 35 ° Pin B is in a double-shear connection…

Q: [36 18 s system is given by 18 -9 145 0 45 0 -27

A:

Q: The 2-m-long tube is made of an elastic perfectly plastic material as shown. Determine the applied…

A:

Q: A LAB(m) В -Li(m)·

A:

Q: The copper pipe [G = 7,000 ksi] has an outside diameter of 3.000 in. and a wall thickness of 0.125…

A: For solution refer below images.

Q: The d = 13-mm-diameter solid rod passes through a D = 18-mm-diameter hole in the support plate. When…

A: Given:The diameter of solid rod, d = 13 mmThe diameter of hole, D = 18 mmThe thickness of support…

Q: A steel shaft with a length of 3.00 m. One meter of the steel is contained in a brass tube and…

A:

Q: Two shaft of diameter 50 mm are joined by a rigid flange coupling and transmit a torque in such a…

A: Here, Shaft diameter = dsh = 50 mm Allowable shear stress in shaft = τsh = 100 N/mm2 Pitch circle…

Q: Two loads P act as shown, one parallel to (x0) and another parallel to z0; each load P equals 2.5…

A:

Q: nd hemispherical shells, The bol and the 25 mm diameter bo able normal stress of 150 M

A: given data  tank thickness = 50 mm no of bolt/ length = 40  dia of bolt =25 mm allowable stress for…

Q: A machinery uses a helical tension spring with wire diameter of 3 mm and coil outside diameter of 35…

A:

Q: The thin-walled pressure vessel shown was fabricated using a spiral seam. The inner diameter is…

A:

Q: Two loads P act as shown, one parallel to (x0) and another parallel to z0; each load P equals 2.0…

A:

Q: A solid circular shaft of length of 3 m and diameter of 50 mm rotates at 1200 rpm by a 400 HP…

A:

Q: The turbine develops 230 kW of power, which is transmitted to the gears such that both B and C…

A: Given, P=230 kwGst=75 GPad=100 mmω=720 rev/min…

Q: n 66 mm diameter alloy shaft is 6.5 m long and subjected to twisting. The shaft is attached to a…

A: Given: The overall length, L = 6.5 m The shear modulus, G = 81 GPa Teh diameter of shaft, d = 66 mm…

Q: A pressure-vessel head is fabricated by gluing the circular plate to the end of the vessel as shown…

A: Given:Internal pressure in the cylinder, P=450 kPa=450*103 PaThickness of the circular plate, t=10…

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.