0.074 in in

Q: 1.3 Determine the length of side a and the measure of the two acute angles. 72.0' 67.3'

A: find the side a and two acute angles.

Q: A compressor motor has a shaft diameter of 7⁄8 inch. The felt wiper that wrapstightly around the…

A: Given    Diameter,d = 7⁄8 inch.

Q: The top of a piston for a compressor has an area of 3.4 sq in. Find the areato the nearer thousandth…

A: Solution     1 sq in = 6.4516 square centimeter

Q: What is the rate of flow of water passing through a pipe with a diameter of 1944 mm and a speed of…

A:

Q: The beam in the figure below is subjected to a load P= 3.9 kN at its end. Young's modulus is 210 GPa…

A:

Q: The capacity of the bowl is liters.

A: Given: R=370 mm To find : Capacity of bowl

Q: 3. It is desired to design a 5-cylinder aircraft engine with a stroke-bore ratio of 1.2. The piston…

A: here, stroke bore ratio say, l/d ratio = 1.2 so, l = 1.2×d volume per cylinder = π4·d2·l here,…

Q: 9. Find the volume of a hollow sphere if it's inside diameter is 1 inch and the outside diameter 5…

A: The volume of a hollow sphere can be obtained using the formula,

Q: A wind turbine has a power coefficient C, = 0.46 and is able to generate 1.6 MW. What was the amount…

A:

Q: 19. Find the resultant and angle of the figure shown below. 1120 N

A:

Q: Compute Îx (I bar sub x, in inches“, round-off to 2 decimal places) for the region shown. 6 in. 6…

A:

Q: A wind turbine has a power coefficient C, = 0.25 and %3D is able to generate 1.3 MW. What was the…

A: Given    Wind power generated, P = 1.3 MW                 Power coefficient = 025

Q: A spring is 15 in. long when loaded with 16 lb and 6.5 in. long when loaded with 25 lb. Determine…

A:

Q: Compute Ix (I sub x, in inches“, round-off to 2 decimal places) for the region shown. 4

A:

Q: A 3500-lb automobile travels down a 10° inclined road at a speed of 20 ft/s. If the driver jams on…

A:

Q: 1-14. The density (mass/volume) of aluminum is 5.26 slug/ft. Determine its density in SI units. Use…

A:

Q: 500 Delermine te Moment about Point (0) 610 as Shown

A:

Q: The distance between two stations A and B is 100 kilometers and its equivalent distance on the…

A: Given dataDistance between two stations D = 100KmLenght on the drawing sheet = 2.5cmMaximum length L…

Q: Comment on accuracy and precision of the spherical ball diameter

A:

Q: What is the rate of flow of water passing through a pipe with a diameter of 1330 mm and a speed of…

A:

Q: Hello, I need help with the answer of 3.14 from the picture, please.

A:

Q: Read the metric caliper in millimeters. Take note that the numbers marked on the main scale are in…

A: The given scale is simple vernier caliper reading. Whose least count is given LC= 0.05 mm  And the…

Q: A cube has an edge length of 7 cm. If it is divided up into 1-cm cubes, how many 1-cm cubes are…

A: Given   Base cube edge 7 cm Segregated cube edge 1 cm To find How many cubes are their

Q: What is the rate of flow of water passing through a pipe with a diameter of 1616 mm and a speed of…

A:

Q: A SHEROID HAS A FIRST ECCENTRICITY OF 0.81427. COMPUTE THE VALUE OF ITS FLATTENING.

A:

Q: If the specific volume of a certain gas is 0.8101 m3/kg, what is its specific weight in N/m3.…

A:

Q: Read the micrometer. 10 5 0. 2 تأسست 3 بليل 4 5 -5 0 -20 The length shown on the micrometer is (Type…

A: Given: To find: Micrometer reading=?

Q: reamer tapers 0.130" along a 4.250" length as shown in the accompanying figure. Set up a proportion…

A: given data; reamer tapers lenth=0.130" along lenth=4.250" determine lenth A=??        when  taper…

Q: ulate the developed blank for the shape shown. Use the empirical forme d your answer to three…

A: given:

Q: If the specific volume of a certain gas is 0.6871 m3/kg, what is its specific weight in N/m3…

A: Giventhe specific volume of a certain gas is  v=0.6871 m3/kg