.. The primary resistance of a 440/1 10-V transformer is 0.5 Q and the secondary resistance is 0.04 n. When 440 V is applied to the primary and secondary is left open-circuited, 200 W is drawn from the supply. Find the secondary current which will give maximum efficiency and cakulate this efficiency for a load having unity power factor. [53 A ; 93.58%]

.. The primary resistance of a 440/1 10-V transformer is 0.5 Q and the secondary resistance is 0.04 n. When 440 V is applied to the primary and secondary is left open-circuited, 200 W is drawn from the supply. Find the secondary current which will give maximum efficiency and cakulate this efficiency for a load having unity power factor. [53 A ; 93.58%]

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: Approximate solution time is 5 minutes. A transformer supplies power to a feeder that has five…

Q: A 240/60 V, single-phase, ideal transformer is to supply power to a load rated at 90 V, 60 Hz. What…

Q: Q) A 50 Hz transformer takes 80 W input at 1.5 A and 120 V. If the primary winding resistance is 0.5…

A: Given- 50 Hz transformer, Input power- Po=80 W,Io=1.5 A,V=120 V,R=0.5 Ω. To Find- No load factor.…

Q: Which of the following is not a property of an Ideal Transfor Select one: O a. L1=* O b. k=1 Oc. R=*…

A: In this question , we will find which is not a property of an ideal transformer..

Q: Q1: The primary of a certain transformer takes 0.7 A at a power factor of 0.5 when it is connected…

Q: In the given circuit, a step down transformer with an RMS voltage as 11ov / 11-0-11 V is used with R…

A: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question and…

Q: An ideal transformer is the one having no losses with some resistance in the winding. Select one: O…

A: Transformer is static device which work on Faraday's Law of electromagnetic induction. If the…

Q: Find the VL (peak) of the center-tapped transformer shown below. Assume ideal transformer and ideal…

A: A full wave rectifier with center tapped transformer is given. In positive half cycle diode D1 will…

Q: 2-An ideal transformer consists of a primary winding (100 turn) and a secondary winding (1000 turn).…

A: Given here an ideal transformer primary winding turns and secondary winding turns and secondary…

Q: A Transformer has turns ratio of 2:15. When the secondary turns is 300, what is the primary turns?…

A: Given, For a transformer the turns ratio is N1N2=215 And the secondary turns is N2=300

Q: A 100kVA transformer has a maximum efficiency of 0.95 at 50% full load and unity power factor .…

A: Electrical machines can be either generator or motors. They can be either Ac machines or DC…

Q: 6) A transformer takes 100V at primary and gives 50V at secondary, its turn ratio equals ... ....…

A: Primary voltage =100V secondary voltage= 50V

Q: E. Use this graphic for question 12 L1 L3 3mH 5mH L2 6mH

A: The solution is given below

Q: The primary of a current transformer takes 1 A at a power factor of 0.4 when it is connected across…

A: Given: N1=2N2Io=1 Acosϕo=0.4I2=50 Acosϕ2=0.8 lag

Q: 10kva single transformer has turns ratio of 300 / 23.

A: The equation of the transformer is given as

Q: An ideal transformer has 3 windings as 100 turns of primary winding, 160 turns on secondary winding…

A: Given- An ideal transformer- 3 windings as 100 turns of primary winding, 160 turns on secondary…

Q: In an ideal transformer having a 1 to 2 turns ratio, the secondary: O a) current is half the primary…

A: In case of ideal transformer, transformer used for transfer the power and stepping up and stepping…

Q: 1. An ideal 200W transformer has an input current of 2 A and an output voltage of 120 V. Determine…

Q: A power suppply having 220 V AC input and two fixed outputs as 10 V DC and 20 V DC is requested from…

A: According to the question, a) Design your power supply and point out DC voltage outputs, b) Explain…

Q: Q2/The primary of a certain transformer takes 1 A at a power factor of 0.4 when it is connected…

A: TRANSFORMER: The transformer transfers power from one circuit to another circuit without a change…

Q: Q2: A 1OKVA distribution transformer has full.load efficiency at o-85 p-f of 95% theca ppe and an…

A: All-day efficiency or energy efficiency: Power transformers are connected after generating station…

Q: A 15kVA, 2400/240, 60 Hz transformer has a primary winding resistance of 4 ohms and a secondary…

Q: Given

Q: b) Find the secondary voltage of an iron-core transformer if the applied voltage is 20 V, and Np=60…

A: Primary voltage is given primary turns is given secondary turns is given

Q: The purpose of using oil in transformers is due to:

A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: Approximate solution time is 5 minutes. A transformer supplies power to a feeder that has five…

A: Given a transformer supplies power to a feeder that has a 5 consumers. Daily maximum demands for…

Q: 1.) A transformer with a rating 600 KVA has an efficiency 0f 94 percentage at full load and at 1/4TH…

Q: 14. The maximum flux of a 50HZ transformer is 0.001Wb. If the primary is wound Vwith 1080 turns,…

Q: A 12V rms ac supply is connected to the primary winding of a transformer with a turns ratio of…

Q: Q/ The primary resistance of a 440/110-V transformer is 0.5 Q and the secondary resistance is 0.04…

A: A 1-ph 440/110 Volts transformer has, Primary resistance (R1)= 0.5 ohm Secondary resistance (R2)=…

Concept explainers

Single Phase Transformer

A single-phase transformer is a type of power transformer. It is an electrical device that accepts converts the single phase alternating power into single phase alternating power. In this power conversion the voltage is stepped up or down. If the voltage is stepped up, the current will be stepped down and if the voltage is stepped down, the current will be stepped up.

Question

.. The primary resistance of a 440/1 10-V transformer is 0.5 Q and the secondary resistance is 0.04
n. When 440 V is applied to the primary and secondary is left open-circuited, 200 W is drawn from
the supply. Find the secondary current which will give maximum efficiency and cakulate this
efficiency for a load having unity power factor.
[53 A ; 93.58%]

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step by step

Solved in 5 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the PIV and dc output voltage in the Figure. The transformer has a 26 V rms secondary voltage rating, and the line voltage has a frequency of 60 Hz.
3. An ideal transformer with a 500 turns primary and 125 turns secondary windings delivers 400W to a 40 load. The resistance of the primary windings is 16O. Find the primary current and voltage
Help me review this example
Subject: Circuits IIIf the secondary of the transformer is step down, the primary will have
The efficiency of a 1000kVA, 110220V, 50Hz single phase transformer is 98.5% at a half load 08 pf and 98.8 % at full-load unity power factor. The voltage regulation is 10% at full-load 0.707 p.f. lag. Determine 1- The efficiency at 80% load and 0.6 p.f. 2- The maximum efficiency.
Please ? help o have no knowledge in this field With explanations
A 200 V/100 V, 50 Hz transformer is to be excited at 40 Hz from 100 V side. For the exciting current to be constant, the applied voltage should be ?
IV- Transformer Design You are requested to design a transformer which will have the following characteristics: Two windings, one primary and one secondary with an E-shape core. Vin = 220 V RMS 16 s Vout < 20 v RMS open circuits 14.5 V < Vout s 16 V on a 100 N resistor. 2 VA < S 35 VA apparent power. Show all steps of your design with calculation. - Indicate current in primary and secondary in both open circuit and with 100 n resistor. Simulate your transformer and show both input and output voltage with the 100 Ω load. Talk about your transformer and wire sizes.
Is it possible have some help with this question, I get 75v for secondary emf and 0.5amps as secondary current!! thanks
a device has an average power rating of 1200W and deisgn to operate 250V rms line. detrmine the effective resistance if the power socket available has 115V rms line and uses a step up ideal transformer from 115V to 250V.
Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across R, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diodeshave? (Use constant voltage drop model for the Silicon diode) D IN4001 OV 10 kN IN4001 DELL