Determine Rz for a 12 V Zener regulator is used with a dc input of 20 V, a load current of 65 mA,and a Zener current of 20 mA.RzDC InputZenerRdiode91.4 ohmsO 14.9 ohms49.1 ohmsO 94.1 ohms The transformer is specified to have a 15 V rms secondary for the standard 120 Vacross the primary. If germanium diodes were used, determine Vout and Vdc for thecircuit shown.D3D120 VVpsec)RD2D 10 knO 20.16 V, 11.11 VO 26.1, 31.11 vO 21.6 V, 11.13 VO 20.61 V. 13.11 Velllelll

determine Rz for a 12V Zener regulator is used with a DC input of 20V, load current of 65mA and a…

Answered: Determine Rz for a 12 V Zener regulator…

Determine Rz for a 12 V Zener regulator is used with a dc input of 20 V, a load current of 65 mA, and a Zener current of 20 mA. DC input Zener R diode O 91.4 ohms O 14.9 ohms O 49.1 ohms O 94.1 ohms

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: Q7. Determine the effective value of the output waveform when VIN= -5+ 5sin(100rt). Diode parameters…

A: To solve above question, one should know about Zener diode and its application. A Zener diode is a…

Q: For positive half of the signal below, what is the peak output value of the circuit? NOTE: use…

A: During negative cycle when vin< -9.3V diode will conduct and capacitor will charge upto Vc=…

Q: A center-tapped FWR circuit have an output dc voltage of 51 V. What is the PIV rating for the diodes…

A: In this question we will find peak inverse voltage rating of diode in center tapped full wave…

Q: D. as Si diode Solve for Ip4 , VRzand IRz DI Rt loma 2K RZ 3IK

Q: The output for the following clamping circuit is shown below assuming ideal diode calculate the…

Q: Draw the output waveform and include the voltage value (silicon diode) R www 2.2 ΚΩ +30 V Vin OV D₁T…

A: Solve the problem

Q: What will happen to the output if the resistor R1 gets damaged and gets shorted ideal diode) D R,…

Q: ortant voltage values. Assume the op-amp is ideal and saturates at the positi ative supply voltages…

A: Solution- We can see it is non inverting amplifier so, the gain V0 / Vi = A is , A=1+RfRi here,…

Q: The output voltage in rms of a quadrupler is 20 V. Then the minimum PIV rating for each diode is…

Q: 2. Design a diode clamper to generate the Vo from Vishow in figure below Vo 10v 2.7v -17.3

A: We need to design a circuit for given input and output

Q: 1 ΜΩ 9-16 V '2 ΚΩ AlDe LẠI VGS (Th) = -3 V ID (on) = 4 mA VGS (on) = -7 V Vaso Figure 2: E-MOSFET…

Q: For full wave bridge rectifier, Ripple Factor=19% and Vdc=9V. Find Vrms. . Volt and Vr(P.P). .Volt.…

A: Full wave rectifier Ripple factor = 19% Average voltage Vdc= 9V Then value of rms? Ripple…

Q: The Schottky diode is used in very fast-switching circuits. in circuits requiring negative…

Q: A2/0.Design Circint as the fllowing pescription: A- the positive Cycle of the vout signal is 3.2 and…

Q: ard bias condition the zener diode will work as a Conventional diode Resistor Reverse diode None of…

A: Zener diode:- It is a heavily doped semiconductor device that is designed to operate in the reverse…

Q: a full-wave rectifier with a capacitor-input filter provides a dc output voltage of 35V to a 3.3k…

Q: Consider the parallel biased clipping circuit below. The input signal (vin) to the circuit is a and…

A: First we will check when diode will be on or off then we will find out current and voltage .

Q: Question-4: Design a positive biased limiter circuit (use silicon or germanium diode) that limit the…

Q: sketch vo for the following cct. diode 10 0-7U 3VT 510 R=lookn

A: The diode is ON when the voltage across anode is more than the cathode voltage. It is known as…

Q: igure below 2. Design a diode clamper to generate the Vo fromV 2.7N -17.3 -10v UNIVERS

Q: 55. A full-wave rectifier with a capacitor-input filter provides a dc output voltage of 35 V to a…

A: Given in the question: DC output voltage, VDC = 35V Resistance of the load, RLOAD = 3.3KΩ Ripple…

Q: +10 V 1.0 kQ V out Vin oV -10 V

A: Age when diode is on means it is forward biased so V0 = v i When diode is off means it is reversed…

Q: 6-Adding diode in the TRIAC control circuit leads to:* further shifting of the firing angle to start…

A: Since the triac can be turned "ON" by either a positive or negative Gate signal, regardless of the…

Q: Input: 20 V -20 V 6+

A: Given circuits: and input: To find: Draw the output waveform of the following Clamper’s circuits…

Q: In power Diode the lightly doped n- epitaxial layer is called drift region Select one: O True O…

Q: Jsing a positive Clamper Circuit, with an AC voltage of Vi = 13v with a frequency of 50hz, a value…

A: As per company guidelines we can solve only first question kindly post another question separately

Q: In the adjacent circuit, the input signal Vin +15V is a square wave. Plot the output signal as a…

Q: Problem No.3 (P3). A biased parallel clipper is connected to a squarewave 20VAC input.The biasing…

A: First draw the arrangement of given clipper circuit configuration and than draw output waveform…

Q: The PIV of half-wave rectifier circuit with a shunt capacitor :filter is a. 2 Vsm b. Vsm O c. Vsm/2…

A: Let's consider the case for a half-wave rectifier without a filter:

Q: Given a negative series clipper (biased), determine the maximum peak amplitude of the output.…

Q: The below circuit is a thermometer with a Type-K thermocouple. Red cable (the first cable) is…

Q: piscussion:- 1. Sketch Vo A 02 20 V 2. Design a diode clamper to generate the Vo from inigure below…

Q: What will happen to the output if the diode D1 gets damaged and gets shorted (deal diode) D, SK, O…

Q: (VPP of input is 18 V. The positive peak value of output waveform for the given circuit diagram is.…

A: In the question, The positive peak value of the output waveform for the given circuit, If the peak…

Q: Tunnel diode is used as a very fast switching device in computers and also used in high frequency…

A: Tunnel diode is used as a very fast switching device in computers. Tunnel diode also used in high…

Q: What will happen to the output if the diode D1 gets damaged and gets open Ocheal dkadn) D, O half of…

A: We need to tell the correct option for the given circuit condition.

Q: A 4-layer diode turns on when the anode-to-cathode voltage exceeds 0.7 V O The gate voltage the…

A: Here is the explanation

Q: The DC voltage and peak-to-peak ripple voltage across the load resistance of an inductor filter…

Q: 19. A biased clamper is connected to a rectangular AC input with 20V on the positive half cycle and…

A: CLAMPERS: The clampers circuit is used to insert a d.c component into the applied input signal, by…

Q: R1 IN OUT R + D1 RL 12V A 800 BZX84C12L

Q: Which of the following is a two-ended trigger element that passes current in two directions? A)…

A: Diode only allows the current to flow in one direction i.e. anode to cathode.

Q: The Schottky diode is used O in very fast-switching circuits. O in power supply rectifiers. O in…

A: Power diodes are a two-layer, two-terminal p-n junction semiconductor device; it has one p-n…

Q: A pn junction that radiates energy as light instead of as heat is callec O photo cell O Photo diode…

A: Diode is semiconductor device. The current flow in diode in one direction only. The diode is OFF…

Q: what is the magnitude of the output swing? O a. 20V O b. 20.3V O c. -34.3V O d. 30V

A: We need to find out the output swing for given clampper circuit .

Q: v(t) 20V RO -20V A laptop charger is connected with a load resistance R=47670 and practical PN…

Q: 20. A biased clamper is connected to a rectangular AC input with 20V on the positive half cycle and…

A: Time constant = product of capacitor and resistor connected in circuit. Given resistance R = 100 K…

Q: * One of the Zener diode applications is .......... O Current regulator O Power regulator O None O…

A: Answer: Option:-4: Voltage regulator

Q: Exercise 2: A single phase half wave ac regulator using one SCR in anti-parallel with a diode feeds…

A: As per Bartleby guidelines we are allowed to solve only one question, please ask the rest again.

Q: 5. Determine the minimum input voltage required to turn on the Zener diode in the following circuit.…

A: So we have to find minimum boltage for breakdown.

Q: Given the circuit below, during the negative half cycle of the input the zener diode is reversed…

A: for the given circuit below, during the negative half cycle of the input the Zener diode is reverse…

Question

Determine Rz for a 12 V Zener regulator is used with a dc input of 20 V, a load current of 65 mA,
and a Zener current of 20 mA.
Rz
DC Input
Zener
R
diode
91.4 ohms
O 14.9 ohms
49.1 ohms
O 94.1 ohms

The transformer is specified to have a 15 V rms secondary for the standard 120 V
across the primary. If germanium diodes were used, determine Vout and Vdc for the
circuit shown.
D3
D
120 V
Vpsec)
R
D2
D 10 kn
O 20.16 V, 11.11 V
O 26.1, 31.11 v
O 21.6 V, 11.13 V
O 20.61 V. 13.11 V
ell
lelll

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: given data

VIEW

Step 2: solution

VIEW

Step 3: determine V out and V dc for the circuit shown

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Three Phase Controlled and Uncontrolled Rectifiers

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A full-wave rectifier produces a 32V peak rectified voltage from a 50Hz ac source. Determine the filter capacitor needed to provide a DC output voltage 24V across a 500 ohm load.
A buck regulator has Vsource 15 V. The average output voltage required is Vo=6 V with peak-to-peak ripple input of 10 mV, the switching frequency is 20 kHz and the peak-to-peak ripple of current of the inductor L is 0.6 A. Calculate the duty cycle and the values of Land Crequired.
Using an ideal diode, design a clamper circuit that result in the desired output waveform as shown in Figure Q7. Show overall analysis to justify the proposed design. 7. Vo Vi Designed Clamper Circuit - 3 V -20 - 43 V - Fiqure Q7 20
Find the average value of the full- wave rectifier if Vpeak = 20V %3D O a. 14.14V O b. 7.07V C. 12.73V O d. 6.36V
Design the Clipper-Clamper circuit to perform the output waveform shown in figure below. GaAs Diode GaAs Diode Vo f=1 kHz. 3 V + -3V Clipper Clamper -13 V -10 V
An FWR using a centre-tapped Transformer Supplies an average voltage of 120V to a 250 kΩ load Calculate (a) the peak value of output voltage (b) The required Transformer secondary voltage (rms value) (c) Average Current delivered to load (d) Average current through each of the diodes. (e) Peak Current through each of the diodes (f) PIV requirements for each of the diodes. AC supply voltage is 230V and assume ideal diodes.
The DC value of a full-wave rectified voltage with a peak value of 55 V is a.) in bridge-type b.) in center-tapped
The positive peak value of output waveform for the given circuit diagram is. Bias voltage is 2 V, Diode is germanium) (VPP of input is 18 V, V VouT
Using a positive Clamper Circuit, with an AC voltage of Vi = 100v with a frequency of 30hz, a value of 1000u for the Capacitor, a silicon diode and a resistor with the value of 100 ohms. Find the voltage value on the resistor at a simulation of Oms. Vm 2Vm Vo -Vm Input Waveform Output Waveform Positive Clamper circuit
Using a positive Clamper Circuit, with an AC voltage of Vi = 100v with a frequency of 30hz, a value of 1000u for the Capacitor, a silicon diode and a resistor with the value of 100 ohms. Find the voltage value on the resistor at a simulation of Oms. Vm 2Vm Mr. Vm Vo -Vm Input Waveform Output Waveform Positive Clamper circuit
An AC voltage peak value of 20 Volts is connected in series with a silicon diode and load resistance of 500 ohms. if the forward resistance of diode is 10 ohms. Find the peak current through the diode and the peak output voltage? Vin 500 2 out O 32 mA, 25 V O 30 mA, 15 V O 37.8 mA, 18.9 V O 40 mA, 20 V
Design the Clipper-Clamper circuit to perform the output waveform shown in figure below. GaAs Diode GaAs Diode Vo f=1 kHz. 3V + -3V Clipper Clamper -13 V -10 V