. Question 1: a. Draw a simple circuit diagram with a battery and a light bulb and how you can simultaneously use a voltmeter to measure the voltage drop across the resistor and use an ammeter to measure the current through the resistor. Label both circuit elements along with the current using the notation from Figures 1 and 2. b. If the battery voltage is 2V and the light bulb resistance is 100, what is the current in this circuit?

. Question 1: a. Draw a simple circuit diagram with a battery and a light bulb and how you can simultaneously use a voltmeter to measure the voltage drop across the resistor and use an ammeter to measure the current through the resistor. Label both circuit elements along with the current using the notation from Figures 1 and 2. b. If the battery voltage is 2V and the light bulb resistance is 100, what is the current in this circuit?

Physics for Scientists and Engineers: Foundations and Connections

1st Edition

ISBN:9781133939146

Author:Katz, Debora M.

Publisher:Katz, Debora M.

Chapter29: Direct Current (dc) Circuits

Section: Chapter Questions

Problem 51PQ

See similar textbooks

Similar questions

Consider the circuits shown below, (a) What is the current through each resistor in part (a)? (b) What is the current through each resistor in part (b)? (c) What is the power dissipated or consumed by each circuit? (d) What is the power supplied to each circuit?
(a) What is the terminal voltage of a large 1.54-V carbon-zinc dry cell used in a physics lab to supply 2.00 A to a circuit if the cell’s internal resistance is 0.100 ? (b) How much electrical power does the cell produce? (c) What power goes to its load?
Why is the following situation impossible? A technician is testing a circuit that contains a resistance R. He realizes that a better design for the circuit would include a resistance 73R rather than R. He has three additional resistors, each with resistance R. By combining these additional resistors in a certain combination that is then placed in series with the original resistor, he achieves the desired resistance.
A person with body resistance between his hands of 10.0k accidentally grasps the terminals of a20.0-kV power supply. (Do NOT do this!) (a) Draw a circuit diagram to represent the situation, (b) If the internal resistance of the power supply is 2000 , what is thecurrent through his body? (c) What is the power dissipated in his body? (d) If the power supply is to be made safe by increasing its internal resistance, what should the internal resistance be for the maximum current in this situation to be 1.00 mA or less? (e) Will this modification compromise the effectiveness of the power supply for driving low- resistance devices? Explain your reasoning.
Using your understanding of the nature of internal energy and temperature, explain why we might expect the resistance of a solid to increase if its temperature increases.
Consider the circuit shown in Figure P28.21 on page 860. (a) Find the voltage across the 3.00-0 resistor, (b) Find the current in the 3.00-12 resistor.
(Indicates a review question, which means it requires only a basic understanding of the material to answer. Questions without this designation typically require integrating or extending the concepts presented thus far.) . Six resistors, all having the same temperatures and compositions, are each attached to a battery with voltage V to form a simple circuit. The resistors have different lengths, l, but the same diameters. Rank the circuits according to the current that flows through the resistor from smallest to greatest. If two (or more) circuits have the same current flowing, give them the same ranking. Explain the rationale you used to establish your rankings. Circuit 1: l = 2 cm; V = 3 V Circuit 2: l = 2 cm; V = 6 V Circuit 3: l = 1 cm; V = 3 V Circuit 4: l = 1 cm; V = 6 V Circuit 5: l = 3cm; V = 2 V Circuit 6: l = 3cm; V = 6 V
. All of the electrical outlets in a room are connected in a single parallel circuit (Figure 7.38). The circuit is equipped with a 20-A fuse, and the voltage is 120 V. (a) What is the maximum total power that can be supplied by the outlets without blowing the fuse? (b) How many 1,200-W appliances can be plugged into the sockets without blowing the fuse?
The circuit in Figure P27.34a consists of three resistors and one battery with no internal resistance. (a) Find the current in the 5.00- resistor. (b) Find the power delivered to the 5.00- resistor. (c) In each of the circuits in Figures P27.34b, P27.34c, and P27.34d, an additional 15.0-V battery has been inserted into the circuit. Which diagram or diagrams represent a circuit that requires the use of Kirchhoffs rules to find the currents? Explain why. (d) In which of these three new circuits is the smallest amount of power delivered to the 10.0- resistor? (You need not calculate the power in each circuit if you explain your answer.) Figure P27.34
a. Draw a circuit with a battery and two identical light bulbs (same resistance) in series. Label all circuit elements and the current using the notation from Figures 1 and 2. b. If the battery voltage is 3V and the light bulb resistance is 150, what is the voltage drop across each of the light bulbs? What is the current going through each bulb?
a. What is the equivalent resistance of this circuit? Give your answer in Ohms b. What is the current provided by the battery? c. What is the voltage drop across Resistor 1 (R1)? d. What is the current through Resistor 2 (R2)? e. Since R3 and R4 are in series, the current through them must be equal (I3 = I4). What is this current? f. What is the total power dissipated by this circuit? Remember that total power dissipated is the sum of the power dissipated by each resistor.
a. Using the characteristics of the first figure, determine ID and VD for the circuit of the second figureb. Repeat part (a) with R = 0.57 kilo-ohms.c. Repeat part (a) with R = 0.78 kilo-ohm.d. Is the level of VD relatively close to 0.7 V in each case?