. For an aggregate sample, if you know that the apparent relative density is 2.72 and the water absorption is 1.2%. The dry mass of the aggregate is 514 gm. Find the bulk and saturated surface dry (SSD) relative density values? b. Why does the maximum size of aggregate depend on the clear spacing between bars? Show with a simple sketch.

. For an aggregate sample, if you know that the apparent relative density is 2.72 and the water absorption is 1.2%. The dry mass of the aggregate is 514 gm. Find the bulk and saturated surface dry (SSD) relative density values? b. Why does the maximum size of aggregate depend on the clear spacing between bars? Show with a simple sketch.

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter2: Soil Deposits-origin, Grain-size, And Shape

Section: Chapter Questions

Problem 2.15CTP: In concrete work, Fuller and Thompson (1907) suggested that a dense packing of grains can be...

See similar textbooks

Similar questions

The fineness modulus is a relative measure of how coarse or how fine an aggregate sample is. True False
In specific gravity test for coarse aggregate we found the following results: dry weight A= 3008 grams SSD weight B = 3037 grams %3D Submerged weight C=1907 grams The SSD specific gravity Select one: O a. 2.456 O b. 2.877 O c. 2.688 O d. 2.899
You are given a result of the gradation test of aggregate, calculate and plot the gradation curve on the given semilog graph shee
Qиestion no.08 The result of specific gravity test is given below Weight of saturated aggregate in water =618gm Weight of oven dry sample = 982 gm Weight of saturated surface dry aggregate = 990 gm (i) Calculate the specific gravity of aggregate?
What is the fineness modulus of the fine aggregate sample? (2 decimal places, no need for unit) Blank 1 Add your answer
Q2 (a) A specific gravity test was performed on a sample of fine aggregate and produced the following results: Mass of sand (saturated surface dry) = 520g Mass of sand (oven dry) = 510g Mass of pycnometer with full of water = 1550g Mass of pycnometer with sand and water = 1900g
Sieve analysis test for fine aggregates was performed on a sample of fine aggregates and produced the following results: a. Calculate the percent passing through each sieve. b. Plot the percent finer in a semi-log gradation chart. c. What is the maximum aggregate size of the sample? d. What is the nominal maximum aggregate size of the sample? e. What is the fineness modulus? Is it in typical range? 0.18 0.15 (No. (3/8) INo. 41 (INo. 6) (No. 8)|(No. 10) (No. 16) (No. 20)|INo. 30)|(No. 40)|(No. So) (No. 60)|(No. 80) 100) Sieve Size, 9.5 4.75 3.35 2.36 2.00 1.18 0.85 0.60 0.425 0.30 0.25 0.075 Pan mm (in) (No. 200) Amount 25 59 75 86 115 136 169 192 225 198 173 112 90 33 12 Retained,
In a ready-mix plant, cylindrical samples are prepared and tested periodically to detect any mix problem and to ensure that the compressive strength is higher than the lower specification limit. The minimum target value was set at 5,000 psi. The compressive strength data shown in Table were collected. a. Calculate the mean, standard deviation, and the coefficient of variation of the data. b. Using a spreadsheet program, create a control chart for these data showing the lower specification limit. Is the plant production meeting the specification requirement? If not, comment on possible reasons. Comment on the data scatter.
MAKE A CONCLUSION ABOUT THE EXPERIMENT MOISTURE CONTENT OF AGGREGATES
Sieve analysis test for fine aggregates was performed on a sample of fine aggregates and produced the following results: a. Calculate the percent passing through each sieve.b. Plot the percent finer in a semi-log gradation chart.c. What is the maximum aggregate size of the sample?d. What is the nominal maximum aggregate size of the sample?e. What is the fineness modulus? Is it in typical range?
Example 2: Specific gravity test was conducted for a fine aggregate. If the following data was obtained during the test: - the saturated surface dry weight of the sample = 500 g. %3D - Weight of pycnometer full of water= 750 g - Weight of pycnometer and sample and water= 1050 g. - Oven dry weight of the sample is 475 g. for this aggregate, FIND - The apparent specific gravity. - The bulk specific gravity on an ssd basis. Percentage of absorption.
Q2 (a) A specific gravity test was performed on a sample of fine aggregate and produced the following results: Mass of sand (saturated surface dry) = 520g Mass of sand (oven dry) = 510g Mass of pycnometer with full of water = 1550g Mass of pycnometer with sand and water = 1900g i. Calculate the apparent specific gravity of the fine aggregate. ii. Calculate the gross apparent specific gravity of fine aggregate.