. A section of two-lane, two-way rural road has a 4km length of sustained 5% grade with following characteristics: Design speed 100km/h % with sight distance less than 450m 40% Lane widths 3.3m Shoulder width (each side) 1.0m Directional split 60/40 Percentage trucks 10% Calculate maximum service flow rate for LOS C.

. A section of two-lane, two-way rural road has a 4km length of sustained 5% grade with following characteristics: Design speed 100km/h % with sight distance less than 450m 40% Lane widths 3.3m Shoulder width (each side) 1.0m Directional split 60/40 Percentage trucks 10% Calculate maximum service flow rate for LOS C.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Transportation engineering
Consider divided multilane highway in Congressional Avenue (fp = 0.98) that has six lanes (three lanes in each direction) and is on rolling terrain. The highway has 3.3m lanes with a 1.8m right-side shoulder and a 1.7m left-side shoulder. The posted speed limit is 85 kph. Formerly there were 1.2 access points per km, but recent development by Makati City Central Business District has increased the number of access points to 5.2 per km. Before development, the peak-hour factor was 0.95 and the directional hourly volume was 2500 vehicles with 9% large trucks and buses and 2% recreational vehicles. After development, the peak-hour directional flow is 3000 vehicles with the same vehicle percentages and peak-hour factor. What is the level of service before and after the development of Congressional Avenue? Round-off to the nearest value for the average passenger car speed in kph.
Transportation Engineering
None
A rural freeway has an ideal free-flow speed of 120 km/hr and two-lanes 3.6 m in each direction, with right shoulder lateral clearance of 1.2 m. Interchange are spaced approximately 5 km apart. Traffic consists of 10% trucks & buses and 8% recreational vehs. If the maximum 15-min flow rate is 1760 veh/hr, what is the level of service on a 1.7 km long 3.1% upgrade?
A long segment of suburban freeway is to be designed on level terrain. The level segment, however, is followed by a 4.5% grade, 2.0 miles in length. If the DDHV is 2,500 vehicles per hour with 15% trucks (standard mix), how many lanes will be needed on the (A.) Upgrade, (B.) Downgrade, (C.) Level terrain segment to provide for level of service C? Lane widths and lateral clearances may be assumed to be 12 feet and 6 feet, respectively. Ramp density is expected to be 1.0 ramps per mile. The PHF is 0.92. Good weather, no incidents, no work zones, and regular users of the facility may be assumed.
An existing four-lane freeway in rural area is with the following :information Lane width 3.5m, 0.9m lateral clearance, 1800 veh/hr peak hour volume, PHF=0.9, interchange density =0.90, 5% trucks, 5% buses and the road is within a mountainous terrain. Then based on the HCM procedure, the service flow rate (pc/h/In) is
A six-lane freeway (three lanes in each direction in mountainous terrain has 10-ft lanes and obstructions 1ft from the right edge. There are five ramps within three miles upstream of the segment midpoint and four ramps within three miles downstream of the segment midpoint. The traffic stream consists of mostly commuter with a peak hour factor of 0.84, peak-hour volume of 2500 vehicles, and 4% recreational vehicles. What is the level of service?
A six-lane freeway (three lanes in each direction) in rolling terrain has 10-ft lanes and obstructions (fLw = 6.0 mph) 4 ft from the right edge of the traveled pavement (fic = 0.8 mph). There are five ramps within three miles upstream of the segment midpoint and four ramps within three miles downstream of the segment midpoint. A directional peak-hour volume of 2000 vehicles (primarily commuters) is observed, with 600 vehicles arriving in the highest 15-min flow rate period. The traffic stream contains 12% large trucks (ET = 2.5) and buses and 6% recreational vehicles (ER = 2.0). 1.) What is the estimated free-flow speed of the traffic stream in mph (whole number, nearest 5)? 2.) What is the peak-hour factor 3.) What is the heavy-vehicle adjustment factor? 4.) What is the service flow rate? 5.) What is the service measure value if the average speed of the traffic stream is 65 mph
A multi-lane Minor Arterial is being designed through a level urban area. The current daily volume = 8000 vpd in both directions with 10% Trucks, peak hourly factor 90%and a 60% directional distribution factor. How many lanes are required?
A six-lane freeway (three lanes in each direction) in rolling terrain has 10-ft lanes and obstructions (fLW = 6.0 mph) 4 ft from the right edge of the traveled pavement (fLC = 0.8 mph). There are five ramps within three miles upstream of the segment midpoint and four ramps within three miles downstream of the segment midpoint. A directional peak-hour volume of 2000 vehicles (primarily commuters) is observed, with 600 vehicles arriving in the highest 15-min flow rate period. The traffic stream contains 12% large trucks (ET = 2.5) and buses and 6% recreational vehicles (ER = 2.0). What is the heavy-vehicle adjustment factor (2 decimal places)?
Plz, solve this problem. Transportation Engineering-2 A four-lane highway (2 lanes in each direction) with 3.65m lanes has a horizontal curve designed for a 380 m centerline radius, and a 110 km/hr design speed. The grade is level. Use a driver perception reaction time of 2.5 sec and a vehicle deceleration rate of 3.4 m/sec2. Determine the closest distance any roadside object may be placed to the centerline of the inside lane of the roadway.(note: Do not round any value. Use calculated values).