Write the direct stress formula in its three forms and explain the meaning of each one.
To write: Direct stress formula in three forms and explain the meaning of each one.
Explanation of Solution
The three forms direct stress formula are as follows:
1.
Here,
It means the average normal stress in a member is equal to axial normal force acting on it divided by the area of cross-section on which the normal force acts. It is used to calculate the average stress developed in a member having a cross- sectional area A, when an external force of magnitude P act.
2.
Where,
P is the axial load capacity.
A is the cross-sectional area of the member.
This form of the formula is used to calculate the maximum load capacity (maximum permissible axial load) of a member having maximum permissible stress,
3.
Where,
P is the axial load capacity.
A is the cross-sectional area of the member.
This formula is applicable for Analysis of load capacity.
Want to see more full solutions like this?
Chapter 9 Solutions
Applied Statics and Strength of Materials (6th Edition)
Additional Engineering Textbook Solutions
Thinking Like an Engineer: An Active Learning Approach (3rd Edition)
Manufacturing Engineering & Technology
Mechanics of Materials (10th Edition)
Engineering Mechanics: Statics
Engineering Mechanics: Statics & Dynamics (14th Edition)
INTERNATIONAL EDITION---Engineering Mechanics: Statics, 14th edition (SI unit)
- The state of stress at a point in a member is shown on the element. Suppose that o = -40 MPa , oy = -120 MРа, три — -28 MPа . Part A Determine the normal stress component acting on the plane AB. (Figure 1) Express your answer with the appropriate units. HA ? Figure 1 of 1 Value Units Submit Request Answer Part B Determine the shear stress component acting on the plane A.B. 30% Express your answer with the appropriate units. y = | Value В Units Pearsonarrow_forwardA force F of 40000 lbf is applied to rod AC the negative Y-direction. The rod is 1000 inches tall. A Force P of 25 lbf is applied in the negative Z- direction at point E, and a force R of 75 lbf is applied in the negative Z-direction at point F. Rod AC has a diameter of 1 inch from A to C, a diameter of 1.5 inches from B to C, and all fillet radii are 0.25 in. The rod is made of 1020 CD steel, and has a Sy of 135 ksi, a Sut of 150 ksi, and an ɛf = 0.15. Y A 100 100 200 800 B. „D D. 100 2D view of rod AC in XY planearrow_forwardFind the values of σs and σ22 for the state of the stress shown in Figure 3arrow_forward
- Please answer as per question and in clear handwriting. The state of stress at a point in a structure is shown in the following figure.Decide:(a) The forces acting on an element oriented at an angle in the directioncounterclockwise θ = 15° from the x-axis (Show the results in a sketch ofcorrectly oriented)(b) find the main stresses (Show the results on a sketch ofcorrectly oriented)arrow_forwardThe state of stress at a point in a member is shown on the element. Suppose that o = -50 MPa , oy = -120 MPa , Try = -30 MPa Part A Determine the normal stress component acting on the plane AB. (Figure 1) Express your answer with the appropriate units. HA Value Units Submit Request Answer Figure 1 of 1 Part B A Determine the shear stress component acting on the plane AB. Express your answer with the appropriate units. 30% HA ? Tz'y = Value Units Submit Request Answer Barrow_forwardCan you calculate the stress for the remaining point instead of point 1 only?arrow_forward
- Shows the state of stress (three dimensional) at a point Q within a given stressed body. b- Briefly describe the three normal stress components and the six shear stress components of the stress at point Q. c- Consider a tetrahedron containing point Q and show the forces on the faces of the tetrahedron due to the various stresses. d- How can we derive the equation for the transformation of normal stress by considering the above mentioned tetrahedron?arrow_forwardDetermine the resulting maximum value of the normal stress. Specify the orientation of the plane on which these maximum values occur. **The answer is tensile stress is 0 ksi at 90 degrees. **The answer is compressive stress is 7 ksi at 0 degrees. Can you explain how that is? This was my thought process: I know that tensile would be zero because the force P is actually going inwards and not outwards. I know that means that there would be a compressive force. I am confused on the angles, how is a tensile force going 90 degress if there technically is no force in the tensile direction. And how is there a compressive force at 90 degrees if there is a stress? thank you!arrow_forwardHow is the state of plane stress at the point uniquely represented?arrow_forward
- a-Shows the state of stress (three dimensional) at a point Q within a given stressed body. b- Briefly describe the three normal stress components and the six shear stress components of the stress at point Q.arrow_forwardDetermine the state of stress of a beam at the point shown in Figure 2 to represent: a) the principal stresses; b) the maximum in-plane shear stress and the associated average normal stress. c) For each of the two cases mentioned in (a) and (b), determine the corresponding orientation of the element with respect to the original element shown and sketch the results relative to the longitudinal axis of the beam. Please show the full working to provide sufficient information for the sketching to be complete. 15MPa Figure 2 20° 50MPaarrow_forward200 mm 400 mm 20 mm J A Section a - a F₁ F₂ 4arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY