Concept explainers
A solid cylindrical wheel of mass
Want to see the full answer?
Check out a sample textbook solutionChapter 11 Solutions
University Physics Volume 1
Additional Science Textbook Solutions
College Physics: A Strategic Approach (3rd Edition)
Sears And Zemansky's University Physics With Modern Physics
Essential University Physics (3rd Edition)
University Physics with Modern Physics (14th Edition)
Applied Physics (11th Edition)
An Introduction to Thermal Physics
- Find the net torque on the wheel in Figure P10.23 about the axle through O, taking a = 10.0 cm and b = 25.0 cm. Figure P10.23arrow_forwardA weight with mass ?w=250 g is tied to a piece of thread wrapped around a spool, which is suspended in such a way that it can rotate freely. When the weight is released, it accelerates toward the floor as the thread unwinds. Assume that the spool can be treated as a uniform solid cylinder of radius ?=4.00 cm and mass ?s=100 g. Find the magnitude of the acceleration of the weight as it descends. Assume the thread has negligible mass and does not slip or stretch as it unwinds. Find the tension in the thread.arrow_forwardThe block on a smooth inclined plane is moving down with a constant acceleration of 5m/s^2. The block on the inclined plane is 48 kg and the hanging mass is 16 kg. The radius of the pulley is 0.38 m. The angle theta is 47 degrees. Determine the moment of inertia of the pulley.arrow_forward
- A garage door is mounted on an overhead rail as shown below. The wheels at A and B have rusted so that they do not roll, but rather slide along the track. The coefficient of kinetic friction is 0.50. The distance between the wheels is 2.00 m, and each are 0.50 from the vertical sides of the door. The door is uniform and weighs 977 N. It is pushed to the left at constant speed by an external horizontal force. If the distance h is 1.54 m: a. What is the vertical component of the force exerted on the wheel A by the track? b. What is the vertical component of the force exerted on the wheel B by the track? c. Find the maximum value h can have without causing one wheel to leave the track. A В K 2.00 m h k- 3.00 m Figure 3. The two wheel track of a rusted garage door.arrow_forwardA circular-shaped object of mass 9 kg has an inner radius of 7 cm and an outer radius of 28 cm. Three forces (acting perpendicular to the axis of rotation) of magnitudes 13 N, 22 N, and 13 N act on the object, as shown. The force of magnitude 22 N acts 33◦ below the horizontal. Find the magnitude of the net torque (units Nm) on the wheel about the axle through the center of the object.arrow_forwardA solid cylinder (LaTeX: I\:=\frac{\:1}{2}MR^2 I = 1 2 M R 2 ) potter's wheel is a thick stone of radius 7 m with mass 5 kg. It freely rotates at 9 radian per second. The potter press a wet rag against the rim and exert a radially inward force of 10 N. If the coefficient of kinetic friction between the rag and the wheel is 0.6, find the time needed for the wheel to stop in seconds.arrow_forward
- The wheels, axle, and handles of a wheelbarrow weigh W = 57 N. The load chamber and its contents weigh W₁ = 563 N. The drawing shows these two forces in two different wheelbarrow designs. To support the wheelbarrow in equilibrium, the man's hands apply a force to the handles that is directed vertically upward. Consider a rotational axis at the point where the tire contacts the ground, directed perpendicular to the plane of the paper. Find the magnitude of the man's force for both designs. F F (a) F = (b) F = i i W 0.400 m ¹0.700 m 0.200 m (a) > > 0.600 m' 0.700 (b)arrow_forwardJohn is pushing his daughter Rachel in a wheelbarrow when it is stopped by a brick 8.00 cm high (see the figure below). The handles make an angle of 0 = 20.0° with the ground. Due to the weight of Rachel and the wheelbarrow, a downward force of 407 N is exerted at the center of the wheel, which has a radius of 18.0 cm. Assume the brick remains fixed and does not slide along the ground. Also assume the force applied by John is directed exactly toward the center of the wheel. (Choose the positive x-axis to be pointing to the right.) & (a) What force (in N) must John apply along the handles to just start the wheel over the brick? 1690.53 X Your response differs from the correct answer by more than 10%. Double check your calculations. N (b) What is the force (magnitude in kN and direction in degrees clockwise from the -x-axis) that the brick exerts on the wheel just as the wheel begins to lift over the brick? magnitude KN direction ° clockwise from the -x-axisarrow_forwardA weight is placed 13.0 cm from the center of a turntable. The turntable starts to rotate and the speed is slowly increased. The coefficient of static friction between the weight and the turntable is 0.221. Eventually, the turntable is rotating fast enough so that the weight slides off. What is the speed of the weight at the moment it begins to slide?arrow_forward
- A grindstone in the shape of a solid disk with diameter 0.520 m and a mass of 50.0 kg is rotating at 810 rev/min. You press an ax against the rim with a normal force of 190 N, and the grindstone comes to rest in 7.10 s. Find the coefficient of friction between the ax and the grindstone. You can ignore friction in the bearings.arrow_forwardThe figure below shows a Yo-Yo of mass m =245 g which has an axle of radius r=1.2 cm and a spool of radius R=5.2 cm. The Yo-Yo is placed upright on a horizontal plane. The string is pulled with a horizontal force Fas shown in the figure. What is the maximum magnitude of the pulling force, F. for which the Yo-Yo will roll without slipping? The coefficient of static friction between the Yp Yoand the horizontal plane is r06and the moment of inertia ofthe Yo-Yo about an axis passing thrOLigh its ceter is 1 = (i/2}mRarrow_forwardA potter's wheel having a radius 0.45 m and a moment of inertia of 13.2 kg. m² is rotating freely at 48 rev/min. The potter can stop the wheel in 8.0 s by pressing a wet rag against the rim and exerting a radially inward force of 69 N. Find the effective coefficient of kinetic friction between the wheel and the wet rag. 0.261 Xarrow_forward
- Physics for Scientists and Engineers: Foundations...PhysicsISBN:9781133939146Author:Katz, Debora M.Publisher:Cengage LearningPrinciples of Physics: A Calculus-Based TextPhysicsISBN:9781133104261Author:Raymond A. Serway, John W. JewettPublisher:Cengage Learning