Electric Motor Control
10th Edition
ISBN: 9781133702818
Author: Herman
Publisher: CENGAGE L
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 1, Problem 6SQ
To determine
Choose the best option that represents the switch, which can be used to control the motor manually.
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
9-
Controlled variable is the output of
a.
Plant
b.
Controller
c.
None of the above
d.
Error Detector
Technician A says when testing the voltage output, if the charging voltage is too high, the cause could be an open field wire from the regulator. Technician B says a loose or glazed drive belt could be the cause of too high charging voltage. Who is correct?
A only
B only
Both A and B
Neither A or B
Technician A says that poor connection at the generator output wire can cause charging systems problems. Technician B says that many charging system circuits contain a circuit protection device. Who is correct?
A only
B only
Both A and B
Neither A or B
What is lightning? Describe the mechanism of the lightning discharge.
Please don’t handwringing
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.Similar questions
- (b) Your team are been assigned to develop a portable electrical car jack as shown in Figure 3. The portable electrical car jack has four subsystems; electric wrench, electric jack, electric pump and LED torch light. (i) Create a design tree that include the system hierarchy and components. (ii) Create a functions structure diagram. (iii) Develope a failure mode and effects analysis (FMEA) table that consist of any two subsystems of the portable electrical car jack.arrow_forwardA motor device is labeled 150 mFd. This device is a A. centrifugal switch.B. stator.C. capacitor. D. rotor.arrow_forwardIn the simple lamp dimmer shown here, what method of power control is being used? AC supply Triac Select the correct response. burst firing proportional control feedback control phase controlarrow_forward
- A press's machine cycle is as follows: Lowering the ram: the ram is lowered when 0 The safety screen was open before the cycle began and is now closed (limit switches S4 and S5 actuated) The press is in the home, i.e. upper position (limit switch S6 actuated) Two-hand switches S1 and S2 were not actuated prior to the cycle but are now Halting the ram during lowering: the ram stops 0 ;immediately when One of the two-hand switches is released. Or . The safety screen is opened. Or . .The ram is down (limit switch S3 actuated) Raising the ram: If the ram is down (limit switch S3 actuated), it is raised by the eccentric drive. The safety .screen can be opened and both two-hand switches released The machining cycle is completed when the ram reaches the home position (limit switch S6 actuated) The designer needs for ........conditional output boxes for drawing the ASM-chart for the controller of the aforementioned system 0 C 2 3 O O O O O Oarrow_forward8.a. What is the purpose of relay CRE in the roll stand machine?A. Relay CRE is used as an emergency stop relay.B. Relay CRE is used to control an alarm light.C. Relay CRE is used to power the PLC.D. Relay CRE is used to power the input modules. 8.b. Which one of the following statements is true of a disabled contact or coil?A. The disabled element has been automatically disabled due to module failure.B. The disabled element is held false by the PLC.C. A disabled contact or coil is caused by a faulty memory location in the PLC.D. A contact must be in the disabled state before it can be forced ON or OFF.arrow_forwardDigital control systems Please sir could you solve this question step by step you are the bestarrow_forward
- Industrial Motor Controls 8.a. A typical motor speed control circuit that is controlled by an analog current loop will have a current ofA. 4-20 mA.B. 2-20 mA.C. 5-50 mA.D. 0-10 mA.8.b. Which one of the following statements is true of a disabled contact or coil?A. The disabled element has been automatically disabled due to module failure.B. The disabled element is held false by the PLC.C. A disabled contact or coil is caused by a faulty memory location in the PLC.D. A contact must be in the disabled state before it can be forced ON or OFF.arrow_forward1. Explain what are Temperature sensors and how does it work. 2. Explain what are Magnetic Switches and how does it work.arrow_forwardWrite a ladder program for a washing machine with the following specification: The machine has two push-button switches A and B for turn on and off the machine respectively. The machine has two sensors for weighting, the sensors given the following reading: - Sensorl ON ON OFF OFF Sensor2 ON OFF ON OFF weight 25 KG 20 KG 5 KG 0 KGarrow_forward
- A type of resistance device that can be placed in a DC motor circuit and varied to limit the speed of a motor is called a A. potentiometer. B. variable reluctor. C. rheostat.D. power resistor.arrow_forwardAutomatic kettle is an example of ________________________. a. Servomechanism b. Sequential control system c. Numerical control system d. Process Control systemarrow_forward22) What type of conversion is happening in a DC Motor. a. DC electrical energy to mechanical energy b. AC electrical energy to mechanical energy c. Mechanical to AC Electrical Energy d. Mechanical to DC Electrical Energyarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Electricity for Refrigeration, Heating, and Air C...Mechanical EngineeringISBN:9781337399128Author:Russell E. SmithPublisher:Cengage Learning
Electricity for Refrigeration, Heating, and Air C...
Mechanical Engineering
ISBN:9781337399128
Author:Russell E. Smith
Publisher:Cengage Learning