Fundamentals Of Engineering Thermodynamics
9th Edition
ISBN: 9781119391388
Author: MORAN, Michael J., SHAPIRO, Howard N., Boettner, Daisie D., Bailey, Margaret B.
Publisher: Wiley,
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Question
Chapter 1, Problem 1.22P
To determine
The pressure of gas to move piston upward.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
As shown on the right, a vertical piston–cylinder assembly containing a gas is placed on a hot plate. The piston initially rests on the stops. With the onset of heating, the gas pressure increases. At what pressure, in bar, does the piston start rising? The piston moves smoothly in the cylinder and g = 9.81 m/s2.
1.2
2
2.50 WP A gas undergoes a process in a piston-cylinder assembly
during which the pressure-specific volume relation is pul2 = con-
stant. The mass of the gas is 0.4 lb and the following data are known:
P₁ = 160 lbf/in.², V₁ = 1 ft³, and p₂ = 390 lbf/in. During the process,
heat transfer from the gas is 2.1 Blu. Kinetic and potential energy ef-
fects are negligible. Determine the change in specific internal energy
of the gas, in Btu/lb.
Water contained in a piston-cylinder assembly undergoes two processes in series (point 1 to point 2
and point 2 to point 3):
point 1: T1 = 100°C and P1 = 5bar
point 2: 71= 151.9°C and P2 = 5bar and v2 = 0.300
.300
m³
point 3: 73= 200°C and v3 = .300"
kg
Use the thermodynamic tables A.2, A.3, and A.4 to answer the following questions:
For questions 1, 3, and 5 choose from: subcooled water, saturated water, saturated liquid, saturated
vapor, superheated vapor
1) What is the thermodynamic state of water at point 1:
2- What is the specific volume of water at point 1:
3) What is the thermodynamic state of water at point 2:
4) What is the quality of water (x) at point 2:
3) What is the thermodynamic state of water at point 3:
4) What is the pressure of water at point 3:
(bar)
On paper draw points 1, 2, and 3 on the following P-v and T-v diagrams and show the two processes.
Add number values, units, and constant pressure or temperature lines if needed. Specify which table
you used to find…
Chapter 1 Solutions
Fundamentals Of Engineering Thermodynamics
Ch. 1 - Prob. 1.2ECh. 1 - Prob. 1.3ECh. 1 - Prob. 1.4ECh. 1 - Prob. 1.5ECh. 1 - Prob. 1.6ECh. 1 - Prob. 1.7ECh. 1 - Prob. 1.8ECh. 1 - Prob. 1.9ECh. 1 - Prob. 1.10ECh. 1 - Prob. 1.11E
Ch. 1 - Prob. 1.12ECh. 1 - Prob. 1.13ECh. 1 - Prob. 1.14ECh. 1 - Prob. 1.1CUCh. 1 - Prob. 1.2CUCh. 1 - Prob. 1.3CUCh. 1 - Prob. 1.4CUCh. 1 - Prob. 1.5CUCh. 1 - Prob. 1.6CUCh. 1 - Prob. 1.7CUCh. 1 - Prob. 1.8CUCh. 1 - Prob. 1.9CUCh. 1 - Prob. 1.10CUCh. 1 - Prob. 1.11CUCh. 1 - Prob. 1.12CUCh. 1 - Prob. 1.13CUCh. 1 - Prob. 1.14CUCh. 1 - Prob. 1.15CUCh. 1 - Prob. 1.16CUCh. 1 - Prob. 1.17CUCh. 1 - Prob. 1.18CUCh. 1 - Prob. 1.19CUCh. 1 - Prob. 1.20CUCh. 1 - Prob. 1.21CUCh. 1 - Prob. 1.22CUCh. 1 - Prob. 1.23CUCh. 1 - Prob. 1.24CUCh. 1 - Prob. 1.25CUCh. 1 - Prob. 1.26CUCh. 1 - Prob. 1.27CUCh. 1 - Prob. 1.28CUCh. 1 - Prob. 1.29CUCh. 1 - Prob. 1.30CUCh. 1 - Prob. 1.31CUCh. 1 - Prob. 1.32CUCh. 1 - Prob. 1.33CUCh. 1 - Prob. 1.34CUCh. 1 - Prob. 1.35CUCh. 1 - Prob. 1.36CUCh. 1 - Prob. 1.37CUCh. 1 - Prob. 1.38CUCh. 1 - Prob. 1.39CUCh. 1 - Prob. 1.40CUCh. 1 - Prob. 1.41CUCh. 1 - Prob. 1.42CUCh. 1 - Prob. 1.43CUCh. 1 - Prob. 1.44CUCh. 1 - Prob. 1.45CUCh. 1 - Prob. 1.46CUCh. 1 - Prob. 1.47CUCh. 1 - Prob. 1.48CUCh. 1 - Prob. 1.49CUCh. 1 - Prob. 1.50CUCh. 1 - Prob. 1.51CUCh. 1 - Prob. 1.52CUCh. 1 - Prob. 1.53CUCh. 1 - Prob. 1.54CUCh. 1 - Prob. 1.55CUCh. 1 - Prob. 1.56CUCh. 1 - Prob. 1.57CUCh. 1 - Prob. 1.58CUCh. 1 - Prob. 1.4PCh. 1 - Prob. 1.5PCh. 1 - Prob. 1.6PCh. 1 - Prob. 1.7PCh. 1 - Prob. 1.8PCh. 1 - Prob. 1.9PCh. 1 - Prob. 1.10PCh. 1 - Prob. 1.11PCh. 1 - Prob. 1.12PCh. 1 - Prob. 1.13PCh. 1 - Prob. 1.14PCh. 1 - Prob. 1.16PCh. 1 - Prob. 1.17PCh. 1 - Prob. 1.18PCh. 1 - Prob. 1.19PCh. 1 - Prob. 1.20PCh. 1 - Prob. 1.21PCh. 1 - Prob. 1.22PCh. 1 - Prob. 1.23PCh. 1 - Prob. 1.24PCh. 1 - Prob. 1.25PCh. 1 - Prob. 1.26PCh. 1 - Prob. 1.27PCh. 1 - Prob. 1.28PCh. 1 - Prob. 1.29PCh. 1 - Prob. 1.30PCh. 1 - Prob. 1.31PCh. 1 - Prob. 1.32PCh. 1 - Prob. 1.33PCh. 1 - Prob. 1.34PCh. 1 - Prob. 1.35PCh. 1 - Prob. 1.36PCh. 1 - Prob. 1.37PCh. 1 - Prob. 1.38PCh. 1 - Prob. 1.39PCh. 1 - Prob. 1.40PCh. 1 - Prob. 1.41PCh. 1 - Prob. 1.42PCh. 1 - Prob. 1.43PCh. 1 - Prob. 1.44PCh. 1 - Prob. 1.45PCh. 1 - Prob. 1.46PCh. 1 - Prob. 1.47PCh. 1 - Prob. 1.48PCh. 1 - Prob. 1.49P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Three-tenths kilogram of a gas is contained within a piston-cylinder assembly. The gas undergoes a process for which the pressure-volume relationship is PVA1.6 = constant. The initial pressure is 73 psi, the initial volume is 10 ft3, and the final volume is 15 ft3. The change in specific internal energy of the gas in the process is 35 kJ/kg. There are no significant changes in kinetic or potential energy. Determine the net heat transfer for the process, in kJ. Select one: а. 11.66 b. -4.4 С. 40.8 d. 61.8arrow_forwardAn air bubble rises from the bottom of a well where the temperature is 25oC, to the surface where the temperature is 27o If the depth of the well is 5m and the atmospheric pressure is 101.325kPa, determine the following: Initial pressure inside the air bubble (P1). Volume of air bubble at state 1. Volume of air bubble at state 2. Percent increase in volume of the bubble.arrow_forward1Kg of water contained in a piston-cylinder assembly undergoes five processes in series as follows: Process 1-2: constant pressure heating at 10 bar from saturated vapor Process 2-3: constant volume cooling to P; = 5 bar and T; = 180°C Process 3-4: constant pressure compression to x=0.45 Process 4-5: constant volume heating to Ps = P1 Process 5-1: constant pressure heating to saturated vapor a. Sketch the above processes on both T-v and P-v diagrams b. Find quality at point 5, and the work done in each processarrow_forward
- P1.1 Identify the thermodynamic systems that may be useful in the analysis of the following physical situations. Draw the appropriate boundaries and describe the type of system, the nature of the boundary, and the type of interactions that occur between the system and its surroundings. (i) A hot block of metal cooling at the bottom of a tank of water. (ii) Current flowing through a section of an insulated electrical cable. (iii) Water filling a storage tank from its bottom.arrow_forward* Your answer is incorrect. A piston-cylinder assembly contains 0.7 lb of propane. The propane expands from an initial state where p₁ = 60 lbf/in.² and T₁ = 70°F to a final state where p₂ = 10 lbf/in.² During the process, the pressure and specific volume are related by pv² = constant. Determine the energy transfer by work, in Btu. W = i 3.123 Btuarrow_forward* Your answer is incorrect. A gas undergoes a process in a piston-cylinder assembly during which the pressure-specific volume relation is pv¹.2 = constant. The mass of the gas is 0.4 lb and the following data are known: p₁ = 160 lbf/in.², V₁ = 1 ft³, and p2 = 300 lbf/in.² During the process, heat transfer from the gas is 2.1 Btu. Kinetic and potential energy effects are negligible. Determine the change in specific internal energy of the gas, in Btu/lb. Δu = i | 76.53 Btu/lbarrow_forward
- A flywheel whose moment of inertia / = 200 lb-ft² is spinning at 220 RPM. For a flywheel, KE = Iw²/2, where w is the angular velocity, rad/s. Let g = 32.2 ft/s². Step 1 How high above the surface of the earth, in ft, would a 70 lb mass have to be raised to have its potential energy equal to the kinetic energy of the flywheel? h = 23.547 Hint Your answer is correct. Step 2 h = i How high above the surface of the earth, in ft, would a 110 lb mass have to be raised to have its potential energy equal to the kinetic energy of the flywheel? eTextbook and Media ft Save for Later Attempts: 2 of 4 used ft Attempts: 0 of 4 used Submit Answerarrow_forwardWhen you add heat to a system, by how much does its temperature change?arrow_forwardA flywheel whose moment of inertia / = 200 lb-ft² is spinning at 210 RPM. For a flywheel, KE = Iw²/2, where w is the angular velocity, rad/s. Let g = 32.2 ft/s². Step 1 How high above the surface of the earth, in ft, would a 80 lb mass have to be raised to have its potential energy equal to the kinetic energy of the flywheel? h = i ftarrow_forward
- A closed system consisting of 10 lb of air undergoes a polytropic process from p₁-70 lbf/in², v₁-4 ft³/lb to a final state where p2 - 20 Ibf/in², v₂-12 ft³/lb. Determine the polytropic exponent, n, and the amount of energy transfer by work, in Btu, for the process. Step 1 Your answer is correct. Determine the polytropic exponent, n, for the process. n-11402 Hint Step 2 Determine the amount of energy transfer by work, in Btu, for the process. W- i Btu Attempts: 1 of 4 usedarrow_forward1. A certain ideal gas Y has molecular weight of 25 g/mol and specific heat ratio of 3. Initially, Y has pressure of 200kPa and volume of 2m3. The volume was doubled during heat transfer. Find the heat transfer if it underwent a process described by ( a. n=1 b. n=Cp/Cv C. n=2arrow_forwardNeed help with this engineering problem. Which unit could be used in the Ideal Gas law equation to get specific volume in ft3/lbm? absolute pressure in lbf/ft2, Temperature in °R and the gas constant in ft·lbf/lbm·°R absolute pressure in lbf/ft2, Temperature in °F and the gas constant in ft·lbf/lbm·°R absolute pressure in lbf/ft2, Temperature in °R and the gas constant in ft·lbm/lbf·°R barometric pressure in lbf/ft2, Temperature in °R and the gas constant in ft·lbf/lbm·°R gauge pressure in lbf/ft2, Temperature in °F and the gas constant in ft·lbf/lbm·°Rarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
What is entropy? - Jeff Phillips; Author: TED-Ed;https://www.youtube.com/watch?v=YM-uykVfq_E;License: Standard youtube license