Heating Ventilating and Air Conditioning: Analysis and Design
6th Edition
ISBN: 9780471470151
Author: Faye C. McQuiston, Jeffrey D. Spitler, Jerald D. Parker
Publisher: Wiley, John & Sons, Incorporated
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 1, Problem 1.10P
A room with dimensions of
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A garden hose attached with a nozzle is used to fill a 40-L bucket. The inner diameter of the hose is 2 cm and
reduces to 0.8 cm at the nozzle exit. If it takes 50 s to fill the bucket with water, Determine the following : -
a) the volume flow rate of water through the hose
b) the mass flow rate of water through the hose
Saturated ammonia at a temperature of 50oF and a flow rate of 3 lbm/s enters a steady-state well-insulated device with an isentropic efficiency of 85%. The device needs to increase the pressure of the ammonia to 200 psia. Calculate the power required (in hp) and the exit temperature (in oF) if
a) The device is a compressor and the ammonia is saturated vapor.
b) The device is a pump and the ammonia is saturated liquid.
Water vapor enters a continuous flow turbine with 6 MPa pressure, 450oC temperature and 80 m/s velocity with a flow rate of 900 m3/h, saturated at 20 kPa pressure.It comes out as steam at a speed of 140 m/s. There is a heat transfer of 5 kW from the turbine to the environment and the turbine inlet section is 150 cm above the outlet section.as it is;a) Find the power produced in the turbine. b) Calculate the adiabatic efficiency of the turbine.
Chapter 1 Solutions
Heating Ventilating and Air Conditioning: Analysis and Design
Ch. 1 - Convert the following quantities from English to...Ch. 1 - Convert the following quantities from SI to...Ch. 1 - A pump develops a total head of 50 ft of water...Ch. 1 - A fan is observed to operate with a pressure...Ch. 1 - The electric utility rate for a facility during...Ch. 1 - For the business whose monthly electrical energy...Ch. 1 - Detmine the interest rate at which the project in...Ch. 1 - How much could a company afford to spend on an...Ch. 1 - Make the following volume and mass flow rate...Ch. 1 - A room with dimensions of 31020m is estimated to...
Ch. 1 - Compute the heat transferred from water as it...Ch. 1 - Air enters a heat exchanger at a rate of 5000...Ch. 1 - Water flowing at a rate of 1.5 kg/s through a heat...Ch. 1 - Air at a mean temperature of 50 F flows over a...Ch. 1 - Repeat Problem 1-10 for air at 10 C, a tube with...Ch. 1 - Air at 1 atm and 76 F is flowing at the rate of...Ch. 1 - Air flowing at the rate of 1000 cfm and with a...Ch. 1 - A chiller is providing 5 tons of cooling to an air...Ch. 1 - Air is delivered to a room at 58 F and the same...Ch. 1 - A chiller is to pro;ide 12 tons of cooling to a...Ch. 1 - Air is being rnished to a 30-ft by 40-ft by 12-ft...Ch. 1 - If cold outside air at 20 F is leaking into a...Ch. 1 - A Btu-meter is a device that measures water flow...Ch. 1 - A heat pump uses a 100,000-gallon swimming pool as...Ch. 1 - A heat pump uses a 100,000-gallon swimming pooi as...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
Find the change in length of side AB.
Mechanics of Materials, 7th Edition
How is the hydrodynamic entry length defined for flow in a pipe? Is the entry length longer in laminar or turbu...
Fluid Mechanics Fundamentals And Applications
A nozzle at A discharges water with an initial velocity of 36 ft/s at an angle with the horizontal. Determine ...
Vector Mechanics for Engineers: Dynamics
Assume the following vectors are already defined: V1=[302]V2=[214]V3=[5131]V4=[0.50.10.20.2] For each of the fo...
Thinking Like an Engineer: An Active Learning Approach (4th Edition)
What is the weight in newtons of an object that has a mass of (a) 8 kg, (b) 0.04 kg, (c) 760 Mg?
Statics and Mechanics of Materials (5th Edition)
List several uses of the arbor press.
Machine Tool Practices (10th Edition)
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Water given in a tank with a pressure of 300 kPa and a flow rate of 3,048 kg/s at 20 °C.here it is mixed with 300 kPa pressure and superheated water vapor in T2 material. Mixture,It exits the mixing chamber with a pressure of 300 kPa and a temperature of 70 °C with a flow rate of 3.264 kg/s. The flow is continuous. There is a heat transfer of 420 kJ/minute to the environment at 25 °C.A) Find the temperature of the heated water vapor entering the mixing chamber.B) Calculate the produced entropy.arrow_forwardDetermine the rate of sensible heat loss from a building due to infiltration if the outdoor air at – 5oC and 90 kPa enters the building at a rate of 35 liters per second when the indoor is maintained at 20oC a. 0.35 kW c. 0.53 kW b. 0.37 kW d. 0.73 kWarrow_forwardQuestion No. 1a) A rigid tank containing 0.4m3 of air at 400 kPa and 30oC is connected by a valve to a piston cylinder device with zero clearance. The mass of the piston is such that a pressure of 200 kPa is required to raise the piston. The valve is opened slightly and air is allowed to flow into the cylinder until the pressure of the tank drops to 200 kPa. During this process, heat is exchanged with the surrounding such that the entire air remains at 30oC at all times. Determine the heat transfer for this process.arrow_forward
- Cold water at a rate of 30 L/min is mixed with hot water at 44 L/min in a continuous manner in a mixing chamber. The rate of water output from the mixing chamber (in kg/s) isarrow_forwardA nozzle is a device for measuring the velocity of flow. At inlet to a nozzle the enthalpy is 3026 kJ/k, the velocity is 60 m/s. At exit from the nozzle the enthalpy is 2790 kJ/kg. The nozzle is horizontal and there is a negligible heat loss from the nozzle. Find he velocity at nozzle exit The inlet area is 0.1 m2 and the specific volume at the inlet is 0.19 m²/s, find the mass flow rate • f the specific volume at the nozzle exit is 0.5 m²/kg, find the exit area of the nozzle (688m/s) (0.36kg/s) (0.0299m2) Air and fuel enter a furnace used for home heating. The air has an enthalpy of 320 kJ/kg and the fuel has an enthalpy of 43027 kJ/kg. The gases leaving the furnace has an enthalpy of 616 kJ/kg. There are 17 kgair / kgfuel, water circulated through the wall furnace receiving heat. The hose required 17.02 kW of heat, what is the fuel consumption per day. (41 kg/day)arrow_forwardAir whose density is 0.078 lb/ft^3 enters the duct of an air-conditioning system at a volume flow rate of 450 CFM. If the diameter of the duct is 10 in, determine the mass flow rate of air in lb/min.arrow_forward
- 2. 1 kg water at velocity 12.5 m/s and 30oC enters a 2.54 cm diameter horizontal pipe where there is no heat or work exchange with the surroundings. The water suddenly flows through a larger pipe with a diameter of 3.85cm. Calculate the following: a. Velocity of the water leaving the pipe in m/s b. The change in temperature of the water. Cpwater=4.18 KI Kg.Karrow_forward2. 1 kg water at velocity 12.5 m/s and 30oC enters a 2.54 cm diameter horizontal pipe where there is no heat or work exchange with the surroundings. The water suddenly flows through a larger pipe with a diameter of 3.85cm. Calculate the following: a. Velocity of the water leaving the pipe in m/s b. The change in temperature of the water. Cpwater=4.18 ?? ??.K Please answer question number 2.arrow_forwardA garden hose attached with a nozzle is used to fill a 40-L bucket. The inner diameter of the hose is 2 cm and it reduces to 0.8 cm at the nozzle exit. If it takes 50 s to fill the bucket with water, Determine the following : - a) the volume flow rate of water through the hose b) the mass flow rate of water through the hose c) the average velocity of water at the nozzle exit оооarrow_forward
- (a) The water in a large lake is to be used to generate electricity by the installation of ahydraulic turbine-generator at a location where the depth of the water is 50 m. Water isto be supplied at a rate of 5000 kg/s. If the electric power generated is measured to be1862 kW and the generator efficiency is 95 %. Determine i) the overall efficiency of the turbine-generator ƞturbine-generator, ii) the mechanical efficiency of the turbine ƞturbine,arrow_forwardA piston-cylinder device contains 0.91 kg of refrigerant-134a at –10°C. The piston that is free to move has a mass of 12 kg and a diameter of 25 cm. The local atmospheric pressure is 88 kPa. Now, heat is transferred to refrigerant-134a until the temperature is 15°C. Use data from the tables. R-134a -10°C Problem 03.030.b - Change of volume of cylinder with refrigerant Determine the change in the volume of the cylinder of the refrigerant-134a if the specific volume and enthalpy of R-134a at the initial state of 90.4 kPa and -10°C and at the final state of 90.4 kPa and 15°C are as follows: 1= 0.2418 m3/kg, m = 247.77 kJ/kg v2 = 0.2670 m3/kg, and h2 = 268.18 kJ/kg The change in the volume of the cylinder is ]m³.arrow_forwardRefrigerant flows through a water-cooled condenser at a rate of 25 kg/ min. The specific enthalpy of refrigerant entering the condenser is 400 kJ/kg, and leaving, is 220 kJ / kg. Determine the mass flow of cooling water through the condenser for a temperature increase of the water of I 0° C, assuming no external heat exchanges.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
The Refrigeration Cycle Explained - The Four Major Components; Author: HVAC Know It All;https://www.youtube.com/watch?v=zfciSvOZDUY;License: Standard YouTube License, CC-BY