Q2) Bioremediation is a method of cleaning up contaminated groundwater and soil. If a dilute solution of nutrients is pumped via a well into a closed soil layer underground at the rate of 1.5 kg/hr, and a recovery well removes 1.2 kg of depleted solution per hour, answer the following Questions: a. What is the system (draw a picture)? b. What is the value of the input per hour? c. What is the value of the output per hour? d. What is the value of the accumulation per hour? e. What assumption has to be made to answer (d)?

Q2) Bioremediation is a method of cleaning up contaminated groundwater and soil. If a dilute solution of nutrients is pumped via a well into a closed soil layer underground at the rate of 1.5 kg/hr, and a recovery well removes 1.2 kg of depleted solution per hour, answer the following Questions: a. What is the system (draw a picture)? b. What is the value of the input per hour? c. What is the value of the output per hour? d. What is the value of the accumulation per hour? e. What assumption has to be made to answer (d)?

Basic Clinical Lab Competencies for Respiratory Care: An Integrated Approach

5th Edition

ISBN:9781285244662

Author:White

Publisher:White

Chapter15: Humidity And Aerosol Therapy

Section: Chapter Questions

Problem 7SEPT

See similar textbooks

Similar questions

%OM pH EC Ca2+ Mg2+ K+ Na+ Al3+ H+ % dS/m cmolc/kg soil cmolc/kg soil cmolc/kg soil cmolc/kg soil cmolc/kg soil cmolc/kg soil 2.7% 7.6 4.5 19 13 10 3 1 4 Is this soil affected? If so, what type? - saline - sodic - not salt affected - saline-sodic
● • 24) Determine the fraction of Vmax that would be found at a substrate concentration of ½2 Km, 2 Km and 10 Km.
Suggest THREE (3) steps that could be taken to reduce phosphorus inputs in water.
(b) (c) Explain the biological requirements for microalgal growth and the main system components for a microalgal processing plant to produce biofuel. How is the system design dependent on its geographical location? A continuous microalgal production system is being developed using a raceway design to produce biofuel from CO2 sequestration. Calculate the area of the raceway (m²) to sequester 2000 tons of CO₂ per year if the growth rate is 75mg/L-day and estimate the amount of biofuel that could be produced. Clearly state any assumptions that you make.
Name two soil properties that can affect infiltration rates. How does application rate affect infiltration? Why are infiltration rates typically higher in a sandy than in a clay soil?
Q 01 (1 pt.): A variation of centrifugation where the solution in the centrifuge tube varies in density (less dense at the top, more dense at the bottom) is called? differential centrifugation B. isopycnic centrifugation C. fractional centrifugation D. А. variable precipitant centrifugation E. density centrifugation Q 02 (1 pt.): Which of these can either stabilize or disrupt the native fold/structure of a protein? solution pH B. temperature С. А. presence of proteases D. concentration/amount of detergent Е. solution ionic strength Q 03 (5 pt.): Draw: Draw a single/in-solution L- histidine (@ solution pH = 7.5), using a Fischer projection. Make sure to specify all charge states and give the overall charge. (Free gift: pKa1 3D 1.8, pКa2 %3D9.2, pКа3 3D 6.0) ||| || |||||
1.1 Microbes in the soil could be beneficial to plants and one way to evaluate this is by determining the R/S ratio. Define the R/S ratio. 1.2 Both rhizospheric and root-free soils were collected from five (5) plants before (BT) and after (AT) treatment. Using the microbial biomass that appear in Table 1, the R/S ratios before (BT) and after (AT) can be determined. Use these values to determine the respective R/S ratios. Kindly show all workings. Microbial population Before Treatment (BT) Plants R/S Microbial population After Treatment (AT) R/S ratio ratio (BT) (AT) Rhizospheric Non- soil (CFU) Rhizospheric Non- rhizospheric soil (CFU) soil (CFU) rhizospheric soil (CFU) Typha sp. 764 168 988 186 Pistia sp. 286 86 386 112 Salvinia 397 132 528 166 sp. Lemna sp. 274 121 406 152 Eichhornia 443 140 648 196 sp.
Explain this example of the following water quality serial dilution. Note the dilution factors and how you would calculate #’s from the incubated plates. ……A serial dilution yielded TNTC in the 1:1 plate and the 1:10 plate, 10 cfu’s in the 1:100 plate and 1 cfu’s in the 1:1000 plate .
RESULTS Please give the time-absorbance values tab? Draw graph-growth curve in Excel? Find the equation of slope line? Calculate the generation time? Choose the values in log phase Abs 0.005 25 0.003 50 0.023 75 0.026 100 0.029 125 0.035 150 0.1 175 0.26 200 0.32 225 0.375 250 0.42 275 0.46 300 0.475 325 0.489 350 0.506 375 0.515 400 0.521 425 0.526 450 0.532 475 0.522 500 0.515 525 0.514 550 0.506 575 0.489 600 0.465 625 0.42 650 0.38 675 0.36 700 0,345 725 0.333 BACTERIAL GRO WTH CURVE
Write a short note on "Need of Medium Optimization".
. You are working at the Loy Farm and are tasked with analyzing water supply for agriculture purposes. Answer the following questions: a) You run an experiment to estimate the water flow rate of the drip irrigation system in the Elon High Tunnel greenhouse. You randomly place 10 small 1-quart paint buckets in the soil along the irrigation system. The table below summarizes the water volume collected in the buckets. The irrigation system was running for 2 hrs. Each bucket has a diameter of 11.2 cm, and volume was measured in milliliters (ml). What is the average drip flow in the irrigation system in inches/hr? (Hint: look up the formula for the area of a circle if you don't already know it). Bucket Number Volume, ml Bucket Number Volume, ml 1 828 6 423 2 829 7 661 3 915 8 885 4 969 9 391 5 887 10 713 b) The open-air crop beds are 7952 ft2 in area. The soil is prepared to a depth of 24…
Relate the terms presented in the first column with the information in the second column; i. Temperatureii. face speediii. Relative humidityiv. Transport and storage timev. Exposure time and concentration of pollutants (__) May influence the integrity of the sample;(__) Influence the amount of sample collected(__) Defines the choice between a sampler containing hydrophilic adsorbents or one with hydrophobic adsorbents.(__) Influences the effective length of the diffusion path.(__)Variation in sampling due to its influence on the diffusion coefficient