NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. End A of the 12.5-kg uniform rod AB of length L = 1200 mm is attached to a collar that can slide without friction on a vertical rod. End B of the rod is attached to a vertical cable BC. The rod is released from rest in the position shown.

NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. End A of the 12.5-kg uniform rod AB of length L = 1200 mm is attached to a collar that can slide without friction on a vertical rod. End B of the rod is attached to a vertical cable BC. The rod is released from rest in the position shown.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

8. 1) Rods AB and BC are linked at Band have weights of 20 lb and 37 Ib, respectively. The 9-lb collar C, which is connected to BC and the spring, slides freely along the smooth vertical guide. The lengths of the rods are 4 = 1.3 ft and 2 = 3.2 ft. If the system is released from rest when 0 = 0°, determine the ratio r= WABI WBC of the angular velocities or rod AB and rod BC when e = 90°. Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point. 11 A В k C Your Answer: Answer
A solid homogeneous cylinder of radius r = 0.5m and mass of m = 100kg is rolled up a 0 20° incline by a force of P = 350N starting from rest. Compute the velocity vG of the center of mass of the cylinder into 6 seconds of motion. Note: Mass moment of inertia about G is given as IG = (1/2)mr². W,a v,a G m Your answer: 32.2 m/s 80.6 m/s 364.5 m/s 9.5 m/s 444.5 m/s 73.0 m/s
Required information The uniform thin rod AB is pin-connected to the slider S, which moves along the frictionless guide, and to the disk D, which rolls without slip over the horizontal surface. The pins at A and B are frictionless, and the system is released from rest. Neglect the vertical dimension of S. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. B D R Letting L = 1.75 m and R= 0.65 m, assuming that S and D are of negligible mass, that the mass of rod AB is MAB= 7 kg, and that the system is released from the angle 0o = 65°, determine the speed of the slider S when it strikes the ground. (Round the final answer to four decimal places.) The speed of the slider S when it strikes the ground is m/s.
A 15-kg uniform disk is placed in contact with the ground and a constant couple moment M = 32 N.m is applied to it as shown. The weight of link AB is negligible. If the coefficient of kinetic friction at D is 0.3, find the angular acceleration of the disk. write the answer in rad/s? but do not write the units. R = 0.25 m A Taylor Answer:
The slender bar has length / and mass m, and it is released from rest in the vertical position with the small roller at end A resting on the smooth incline. If m = 0.5 kg, 1 = 1.2 m, and = 30°, calculate the magnitude of the bar's initial angular acceleration. Present your answer in rad/sec² using 3 significant figures. An efficient coordinate system is necessary to simplify the math.
item 2 Part A - Angular Acceleration of the Rod Learning Goal: The slender rod AB shown has a mass of m = 61.0 kg and is being supported by a rope and pulley system stationed at C. Starting from rest (in the position shown), the rope and pulley system tug on the rod causing it to rotate about A. The torque applied to the pulley is T = 2.15 kN-m and has an effective moment arm of r = 0.160 m. The dimensions shown in the figure are l = 2.10 m and h = 1.40 m. Assume the pulley is frictionless Determine the angular acceleration of the rod the instant the rope and pulley system have pulled the rod through an angle of 0 = 3.10°. Express your answer to three significant figures and include the appropriate units. View Available Hint(s) HÀ ? and maccloce Figure 1 of 1 Value Units Q = Submit C Part B - Normal Component of the Reaction at A h Determine the normal component of the reaction the rod exerts on the pin at A. Use the coordinate system set up by the free-body diagram below.
The cylinder is uniform and has a mass of 5.00 kg. It is released from rest.a) Calculate the least coefficient of friction between the cylinder and the plane for which the cylinder will roll without slipping.b) Calculate the acceleration of the center of mass G of the cylinder if it rolls without slipping.
The 35 lb slender rod AB is 277 in. long and at rest in a horizontal position supported by a spring located at h = 226 in. from the suspension cable at B. If the cable at B fails, answer the following 1) Part A: Determine the magnitude of the acceleration of end A. 2) Part B: Determine the magnitude of the acceleration of end B. 3) Part C: Determine the angular acceleration of the rod.
1. (bold type indicates a vector) An object of mass m = 10 kg may rotate in a vertical plane about the fixed point P under the action of gravity. The distance d from the point P to the center of mass C is d = 0.5 m. The moment of inertia Ie about the center of mass C is unknown. The object starts at rest in the position shown and is then released. At the instant of release the acceleration of the center of mass is measured to be a, = (-5 m/sec²)j (i.e., downward). Use the given information to determine the moment of inertià I, about the center of mass. Use g = 10 m/sec?. gravity w go P (f ixed)
QUESTION 12 The hammer throw athlete in Figure Q12 is initially at rest and starts revolving about his/her body axis with an angular acceleration 1.5 rad-s-2 until he/she eventually releases the ball of mass m = 7.47 kg at the end of 5 revolutions. Determine the centripetal force (pull) that the athelete applies at the instant of release if the wire has length R = 0.81 m. Ignore gravitational forces. Provide only the numerical value (in Newtons) to zero decimal places and do not include the units in the answer box. Figure Q12: Hammer throw R m
8. The 20 kg uniform disk of radius r= 0.4 m is at rest on the incline (0 = 20°) when a constant force T= 200 N is applied as shown pulling the cord that is securely wrapped around the rim of the disk. If the coefficients of friction on the incline are u, = 0.3 and u, = 0.2, determine the friction force between the disk and the incline, the angular acceleration of the disk, and the acceleration at the mass center G. F (magnitude and direction) - T a (magnitude and direction) =. ac (magnitude and direction) = G
3. In the diagram below, a force P of 750 N is applied to the 350 kg block. Find the acceleration of the block and the reaction forces at contact points A and B if the coefficient of kinetic friction between the block and surface is 0.15. 700 mm 700 mm 300 mm 300 mm 400 mm 500 mm'500 mm