Part A- Angular Acceleration of the Rod Learning Goal: The slender rod AB shown has a mass of m = 61.0 kg and is being supported by a rope and pulley system stationed at C. Starting from rest (in the position shown), the rope and pulley system tug on the rod causing it to rotate about A. The torque applied to the pulley is T = 2.15 kN-m and has an effective moment arm of r= 0.160 m. The dimensions shown in the figure are l = 2.10 m and h = 1.40 m. Assume the pulley is frictionless Determine the angular acceleration of the rod the instant the rope and pulley system have pulled the rod through an angle of 0 = 3.10°. Express your answer to three significant figures and include the appropriate units. • View Available Hint(s) HA and maceloce Figure < 1 of 1> Value Units Submit Part B - Normal Component of the Reaction at A Determine the normal component of the reaction the rod exerts on the pin at A. Use the coordinate system set up by the free-body diagram below.

Part A- Angular Acceleration of the Rod Learning Goal: The slender rod AB shown has a mass of m = 61.0 kg and is being supported by a rope and pulley system stationed at C. Starting from rest (in the position shown), the rope and pulley system tug on the rod causing it to rotate about A. The torque applied to the pulley is T = 2.15 kN-m and has an effective moment arm of r= 0.160 m. The dimensions shown in the figure are l = 2.10 m and h = 1.40 m. Assume the pulley is frictionless Determine the angular acceleration of the rod the instant the rope and pulley system have pulled the rod through an angle of 0 = 3.10°. Express your answer to three significant figures and include the appropriate units. • View Available Hint(s) HA and maceloce Figure < 1 of 1> Value Units Submit Part B - Normal Component of the Reaction at A Determine the normal component of the reaction the rod exerts on the pin at A. Use the coordinate system set up by the free-body diagram below.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A momentum wheel for dynamics class demonstration is show. It is basically a bicycle wheel modified with rim band-weighting, handles, and a pulley for cord startup. The heavy rim band causes the radius of gyration of the 3.1 kg wheel tobe 275 mm. If a steady 32 N pull F is applied to the cord, determien the angular acceleration of the wheel. Neglect bearing friciton.
The parallelogram linkage shown moves in the vertical plane with the uniform 9.3-kg bar EF attached to the plate at E by a pin which is welded both to the plate and to the bar. A torque (not shown) is applied to link AB through its lower pin to drive the links in a clockwise direction. When e reaches 51°, the links have an angular acceleration and an angular velocity of 7.0 rad/s² and 2.3 rad/s, respectively. For this instant calculate the magnitudes of the force F and torque M supported by the pin at E. Welded 1435 mm pin F 995 995 mm mm B D Horizontal Answers: F = i N M = i N•m
Wheels A and B are uniform 16.1-lb cylinders with frictionless axles as shown. A 32.2-lb box C with a center of mass at G is supported on the axles. Calculate the acceleration of the box if the wheels roll without slipping.
Name Problem #4 The wheel, with its attached hub weighs 80.5 lb and has a radius of gyration about its mass center of kg = 9 inches. A force P = 25 lb is applied to the cord wrapped around the hub as shown. The applied force causes the wheel to roll without slipping up the incline. Draw a free body diagram of the wheel, showing all forces acting on it. Determine the angular acceleration of the wheel. Determine the normal force at the point of contact with the ground. Determine the friction force at the point of contact with the ground. 6" 12" 20°
The spool has mass, m, and a radius of gyration kG. An inextensible cord is attached to the wall at A. The cord is wound around the radius R and the outer radius 2R. The coefficient of friction between the spool and the ground is mu. What it the critical force, Fcrit (force required to cause motion) applied at point B? If force= 2Fcrit what is the linear acceleration of the center of mass? If force= 2Fcrit what is the tension in cord AC?
The uniform 30-kg bar AB hangs from a pin attached to the 50-kg homogeneous disk C. The system is at rest when the horizontal force P =200N is applied. Find the angular accelerations of the disk and the bar immediately after P is applied.
The spool has a mass m, and a radius of gyration kG. An inextensible cord is attached to the wall at A. The cord is wound around the inner radius, R, and the outer radius is 2R. The coefficient of friction between the spool and the ground is mu. If instead of applying the force, F, at point B, the spool has an initial angular velocity given as omega naught. Use the work-energy principle to determine how far the center G will move before stopping.
The 17-kg wheel is rolling under the constant moment of M = 85 N-m. The wheel has radius r= 0.50 m, has mass center at point G, and the radius of gyration is kg = 0.20 m. The coefficients of friction between the wheel and the ground is ls = 0.27 and Hk; = 0.22. If the wheel rolls while slipping, determine the angular acceleration of the wheel (in rad/s?). Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point. Take g = 9.81 m/s?. M G
In a four bar mechanism the link AB rotates with angular velocity of 20rad/s and angular acceleration of 100 rad/s both in clockwise direction when it make an angle of 45° with link AD which is fixed .The length of various linkages are AB=CD=400 mm,BC=500mm and AD=750mm .Neglect the gravitational effect and friction.The mass of link is 5kg/m. Find the torque on output link E (2) (4) A (1) (1)
4 The uniform 16.1-lb slender bar is hinged about a horizontal axis through O and released from rest in the horizontal position. Determine the distance b from the mass center to O which will result in an ini- tial angular acceleration of 16.1 rad/sec?, and find the force R on the bar at O just after release. G 12" 12"
Question 2 The speed of the pickup truck’s engine is controlled by the Porter governor with 4 arms of equal length, and pivot on the axis of rotation. Each ball has a mass of 4 kg and the mass of the central load on the sleeve is 20 kg. The radius of rotation of the ball is 150 mm when the governor begins to lift, and 200 mm when the governor is at maximum speed. The initial angular speed of the engine’s crank is 14 rad/s, and it has reached a maximum speed at an acceleration of 0.4 rad/s2 after 5 seconds.2(a). If the speed of the crank of an engine is equal to the speed of its governor, calculate the angle between the upper arm and axis of rotation (?) when the governor starts to lift and when it is at maximum speed. 2(b). Prove that the length of the governor’s arms is equal.
The disk shown in the figure has a mass of 15 kg and is supported on point C of its periphery. The disc is released from the rest when theta = 30 ° and impacts with the wall when theta = 0 °. Calculate the reactions at support C, the angular acceleration of the disc immediately after it has been dropped from rest.