Find the strain Initial length=102.78 mm Change in length=0.004 mm
Q: B >1.0 kN 2 m D 2m 2m 8.0 kN Using joint D, what is the axial force on member BD? A) 8.0 kN…
A: GIVEN DATA- A 2D TRUSS GIVEN WE HAVE TO FIND FORCE IN MEMBER BD METHOD USED- METHOD OF JOINT
Q: A 425 mm diameter pipe having 800 m length conveys water from high level tank to a point 22 m below…
A: We know that water is transported from a high-level tank to a place 22 metres below the water level…
Q: In an ideal Rankine cycle, steam is generated at 4.1 MPa and 480°C. The condenser is at 32°C.…
A: GivenP=4.1MPaT1=480oCT2=32oC
Q: A freely falling body is said to be moving with O non-uniform motion O constant non-zero…
A: According to the details provided in the question, we need to define conditions for the free-falling…
Q: b) Production of butanol requires high energy of hot and cold utilities in the production plant. The…
A:
Q: You move a 50-kg crate by pushing it with a 120N force at an angle of 42 degrees above the…
A: Mass of the crate, m= 50 kg Force, P= 120 N Angle, θ= 42∘ Crate is moving with constant velocity.…
Q: Determine the discharge Area of channel=22 m2 Flow velcoity=2.22 m/s
A:
Q: A mass of 15 kg is at limiting equilibrium on a rough plane which is inclined at an angle of 40…
A: Mass, m=15 kgInclination angle of plane, θ=300
Q: Two pumps (Pump A and B) have performance curves which can be approximated by the following…
A: Head Discharge If two pumps are in series Head is not constant Discharge is constant If two…
Q: the net heat input per unit length of the weld.
A: Given data; A gas tungsten arc welding operation is performed usingcurrent=650 A, voltage=10 V…
Q: The average velocity in a pipe flowing full of incompressible liquid is 3 m/s. after passing through…
A: Given Initial velocity, v1 = 3 m/s Initial area = A1 Final area, A2 = A1/4…
Q: A 150 MW power plant using a regenerative cycle is utilizing steam at 5 MPa, 510°C. The open heater…
A: Answer: ◆ The % mass extracted for the 1 MPa open heater is: 9.646%◆ The % mass extracted for the 3…
Q: Q2. The force F = 120 lb acts on the frame. Resolve this force into components acting along members…
A:
Q: P9.10 A multi stage pump is required to deliver of 2.5 l/s water against a maximum discharge head of…
A:
Q: It is required to construct a hydraulic turbine (inward Francis type) for a hydraulic power plant to…
A:
Q: Determine acceleration U= 0.9mls V = 0.45mis += t- 15
A: Given data : Initial velocity=U Final velocity=V Time=t Required : Acceleration
Q: 9. Determine the moment of the 500 N force about point O, as shown.
A:
Q: A mass of 15 kg is at limiting equilibrium on a rough plane which is inclined at an angle of 40…
A:
Q: Water flows from a big tank through a big pipe that divides into two smaller pipes, like in the…
A:
Q: Q2) Several water pipes intersect at the junction box illustrated in Figure. Determine the force…
A:
Q: Find the center of gravity of the circular arc x2+y2=a2, which is in quadrant III
A:
Q: A wire of circular cross-section of diameter 1.0 mm is bent into a circular are of radius 1.0 m by…
A:
Q: A reheat cycle with two stages of reheating is executed, with steam expanding initially from 90 bar…
A:
Q: A reheat cycle with two stages of reheating is executed, with steam expanding initially from 90 bar…
A:
Q: Assuming non-viscous flow, determine the traction force on the flange's bolts shown. We have y=1.8…
A:
Q: Water flows at a rate of 0.035 m3/s in a horizontal pipe whose diameter is reduced from 15 cm to 8…
A: Given Diameter, D = 15 cm d = 8 cm Flow rate, Q = 0.035 m3/s Find Head loss, h
Q: Two forces F, and F₂ act on the screw eye. If the resultant force FR has a magnitude of 601b and the…
A:
Q: Solve the remaining velocity Vd and Ve using the same principle used to get Va,Vb and Vc. Using the…
A:
Q: 1. Draw a table of the working process of a 4-stroke 6-cylinder engine. The firing sequence is…
A:
Q: A = rolled steel channel (I 8.87 x 106 mm, I₁ = 40.3 x 10¹ mm²) is used as a simply supported beam…
A:
Q: volume occupied by 8,968 kg of air at a gage pressure of 723 kPa and a temperature of 686 C .…
A:
Q: A particle is given an initial velocity of 50 meters per second at an inclination having a slope of…
A:
Q: A gas tungsten arc welding operation is performed using a current 350 A and arc voltage of 25 V at a…
A:
Q: The pin-connected structure shown in the figure consists of a rigid beam ABCD and two supporting…
A:
Q: The axle of the freight train is subjected to loadings as shown below. The diameter of the axle is…
A:
Q: ive 5 practical applications in aviation of the concept of thermal expansion. Briefly explain each.
A: The propensity of matter to change volume in response to temperature changes is known as thermal…
Q: 2. A 20-kg crate hanging at D is supported by a horizontal spring AB and a cable AC, as shown.…
A:
Q: The steel shaft shown in Fig. P-314 rotates at 4 Hz with 45 kW taken off at A, 30 kW removed at B,…
A:
Q: Electrical discharge machining process, breakdown voltage across inter electrode gap (IEG) IS 300 V…
A:
Q: a box with a mass 20kg its been pull with a force constant P=W of the box was in constant repose…
A:
Q: A nozzle receives 36 kg/s of air at a speed of 142 m/s and with an enthalpy of 1060.00 kJ/kg. Air…
A:
Q: The force F = 230 lb acts on the frame. Resolve this force into components acting along members AB…
A:
Q: F L h Figure Q1 b) State if the cantilever beam is in plain stress or plain strain and explain…
A: given; lets take width of beam=b lets take reaction force=R
Q: What is the full-load current of a 500-volt, DC, 20-horsepower motor?
A:
Q: Q2. The force F = 230 lb acts on the frame. Resolve this force into components acting along members…
A: Given data F = 230lb Determine the component of force along AB and AC.
Q: Part 2: blem Statement as turbine power plant operates on simple and ideal cycle with air as the…
A: Solution is attached below
Q: or the given beam: (a) Which of the following is the vertical reaction at c. [ Select] (b) Which of…
A: According to the details provided in the question, we need to calculate vertical reaction at A…
Q: Compute the moment of area of the M diagram between the reactions about both the left and the right…
A:
Q: A triangular dam is shown in the figure, base is 6-m and height is 8-m. Compute for the factor of…
A:
Q: Using the relations among load, shear and moment, draw shear and moment diagrams, specifiying the…
A: The section is as shown below,
Step by step
Solved in 2 steps with 2 images
- Tensile test specimens are extracted from the "X" and "y" directions of a rolled sheet of metal. "x" is the rolling direction, "y" is transverse to the rolling direction, and "z" is in the thickness direction. Both specimens were pulled to a longitudinal strain = 0.15 strain. For the sample in the x-direction, the width strain was measured to be ew= -0.0923 at that instant. For the sample in the y-direction, the width strain was measured to be gw=-0.1000 at that instant. The yield strength of the x-direction specimen was 50 kpsi and the yield strength of the y-direction specimen was 52 kpsi. Determine the strain ratio for the x direction tensile test specimen. Determine the strain ratio for the y-direction tensile test specimen. Determine the expected yield strength in the z-direction. Give your answer in units of kpsi (just the number). If the sheet is plastically deformed in equal biaxial tension (a, = 0, to the point where & = 0.15, calculate the strain, 6, that would be expected.Find the value of strain Initial length=120 mm Change in length=0.02 mmDuring a test of an airplane wing, the strain gage readings from a 45° rosette (see figure) are as follows: gage A, 520 × l0-6; gage B. 360 × l0-6; and gage C,-80 × 10-6. Determine the principal strains and maximum shear strains, and show them on sketches of properly oriented elements.
- A strain rosette (see figure) mounted on the surface of an automobile frame gives the following readings: gage A,310 × 10-6:gage B,180 × l0-6; and gage C. -160 × 10-6. Determine the principal strains and maximum shear strains, and show them on sketches of properly oriented elements.An 6 mm diameter aluminum rod has lines scribed on it that are exactly 10 cm apart. After a 2.08 kN force has been applied, the separation between the lines has increased to l' = 10.009 cm. 30 cm 10 cm -F l' a. Calculate the stress and strain in the rod. (Express your answer for stress using two significant figures.) |MPa (Express your answer for strain using four decimal spaces.) E = b. To what total length has the rod stretched? (Express your answer using three decimal places.) L final cmFind the strain Initial length=100 mm Change in length=0.567 mm
- A material is subjected to the following strain system,ex=200x10-6, ey=-56x10-6,yxy=230x10-6. Using graphical method, determine A. The principal strains B. The directions of principal strain axes C. The linear strain on an axis inclined at 50o counter clockwise to the direction of ex Given that young's modulus for the material is 207GN/m2 and the poisson's ratio is 0.27, determine the principal stressesComputing the initial length of rod Strain-0.0078 Change in length=0.05 mmThe figure below shows a hollow circular beam with an outside diameter of 100 mm and a wall thickness of 40 mm loaded in bending with force F = 200 kN. F Ra Rb 1m 1 m Young's modulus of the beam is 80 GPa. Calculate the second moment of area, I, in m* in the form a x 10 0 where the number a is correct to two decimal places. I: x10 m4 Calculate the maximum bending moment, M, in kilonewtonmetres (kNm): M: kNm Calculate the maximum bending stress, o, in megapascals (MPa) correct to two decimal places. MPa
- Q4 A three strain gages have been attached directly to a piston used to raise a medical chair, the strain gages give strains as Ea = 80 µ , Eb = 60 µ and Ec = 20 u . Determine the principal strains and the principal strain directions for the given set of strains. And Compute the strain in a direction -30° (clockwise) with the x axis. 45 PumpTake longitudinal strain 0.02I need help solving the Mohr's circle for strain finding Point A, the center (C) and the radius (R).