An 6 mm diameter aluminum rod has lines scribed on it that are exactly 10 cm apart. After a 2.08 kN force has been applied, the separation between the lines has increased to l = 10.009 cm. 30 cm 10 cm F 4 F l' a. Calculate the stress and strain in the rod. (Express your answer for stress using two significant figures.) o =[ ]MPa (Express your answer for strain using four decimal spaces.) b. To what total length has the rod stretched? (Express your answer using three decimal places.) L final ст

An 6 mm diameter aluminum rod has lines scribed on it that are exactly 10 cm apart. After a 2.08 kN force has been applied, the separation between the lines has increased to l = 10.009 cm. 30 cm 10 cm F 4 F l' a. Calculate the stress and strain in the rod. (Express your answer for stress using two significant figures.) o =[ ]MPa (Express your answer for strain using four decimal spaces.) b. To what total length has the rod stretched? (Express your answer using three decimal places.) L final ст

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A uniaxial force was applied on the shown coupon during an experiment. The thickness, width and length of the coupon are 1mm, 20mm and 100 mm, respectively. the force applied had a magnitude of 1000N. A strain rosette was applied to the sample as shown. Strain gages a and c are perpendicular to each other. On the other hand, the angle between strain gages b and a is 30°. The strain gages reported the following strains Ea = -0.2x10-3 Ep = 0.667x10-3 Determine the elastic properties of the isotropic coupon. 30 a
The Mohr's circle representing a given state of stress is shown. The diagonal line AB represents the original orientation where point A corresponds to the x face and point B corresponds to the y face. a) Show the stresses represented by line AB on the provided stress element. 60 X -30-1 {MPa} y T(MPa) b) Determine the principal stresses and show them on a properly oriented stress A element. y X 40 B 20p 30 40 40
The state of stress at a point on an element of material is shown. Let sigmaX= 49.0 ksi, sigmaY= 17.0 ksi, and Txy= 11.0 ksi. Use this information to represent the principle state of stress and maximum in plane shear stress. Plot the mohr circle and state sigmaX' and sigmaY' and Tx'y' with unit. Also draw the state of stress on the rotated element.
Question 5: (8 marks) The 45° strain rosette shown in Figure 5 is mounted on a machine element. The following readings are obtained from each gauge: Ea = 650 x 106, : b = -300 x 106, and : &c = 480 x 10°. Determine (a) the in-plane principal strains, and (b) the maximum in-plane shear strain and the associated average normal strain. a Figure 5 45° 45°
The Mohr's circle representing a given state of stress is shown. The diagonal line AB represents the original orientation where point A corresponds to the x face and point B corresponds to the y face. a) Show the stresses represented by line AB on the provided stress element. 60 X A 140 (MPa) 40 y B 50 √20p 30 30-1 +(MPa) 40
Find the ox value for the plate as shown below, where b1=d2%=D16 mm, d1=70 mm,b2%=90mm. (ENTER ONLY THE VALUES IN THE BOXES BY REFERING THE UNITS GIVEN IN THE BRACKET) b1 b2 d2 d1
Question 1 The 60° strain rosette is mounted on a beam structure at point A as shown in Figure 1. The following readings are obtained from each gauge: Ea = 250 x 10- Eb =- 400 x 10-6 €c = 280 x 10-6 Determine; (a) the in-plane principal strains and their orientation, (b) the maximum in-plane shear strain and average normal strain. In each case show the deformed element due these strains. 60° 60° 60° Figure 1
The strain rosette shown in figure was used to obtain strain data at a point on the surface of a machine part. If the readings from gages a, b, c were 650, -450, -585 (all in microns) respectively; which of the following is the shear strain on the surface? 45° a Lutfen birini seçin a1370 micron b. 1570 micron c1400 micron d7600 micron
A bar of metal 25 mm in diameter is tested on a length of 250 mm in tension. The following results were recorded: LOAD (KN) 10.4 0.039 DEFORMATION (mm) 31.2 0.089 Determine the strain due to the 31.2 kN load. Express your answers in 6 decimal places.
millimeter. What are two plates joined by three nails with a diameter of 15 T N the shear stress in the material if the shear forces are 1200 7.1 N/mm 20 20 N/mm 20 12 N/mm 20
Question-1: The strain rosette shown in the figure was used to obtain normal strain data at a point on the free surface of a machine part. (a) Determine the strain components &, S, and %, at the point. (b) Determine the principal strains and the maximum in-plane shear strain at the point. (c) Draw a sketch showing the angle 6, the principal strain deformations, and the maximum in-plane shear strain distortions. (d) Determine the magnitude of the absolute maximum shear strain. 45 45 &- 50 με, 8--730 με , ε375 με, ν-0.30
Two rods support the rigid bar ABC as shown in the figure. A downwards load P of 50 kN is applied at A. Rod BD has the following properties: L = 600mm, E = 73 GPa, and A = 1,250 mm². Rod CE has the following properties: L = 400mm, E = 200 GPa and A = 750 mm2. Indicate negative if under compression or if the member contracteri D 200 mm Εἴ 400 mm B 600 mm 300 mm-