An application demands that sinusoidal pressure variation of 250 Hz be measured with no more than 2% dynamic error. In selecting a suitable pressure transducer from vendor catalog, you note that a desirable line of transducer has a fixed natural frequency of 500 Hz but that you have a choice of transducer damping ratio of between 0.5 and 1.5 in increments of 0.05. select a suitable transducer. The value of damping ratio is between the following values Select one: O a. 0.707 and 0.807 O b. 0.631 and 0.692 O c. 0.2356 and 0.5625 O d. 0.5215 and 0.5625 Previous page Next page 1 Assignmen

An application demands that sinusoidal pressure variation of 250 Hz be measured with no more than 2% dynamic error. In selecting a suitable pressure transducer from vendor catalog, you note that a desirable line of transducer has a fixed natural frequency of 500 Hz but that you have a choice of transducer damping ratio of between 0.5 and 1.5 in increments of 0.05. select a suitable transducer. The value of damping ratio is between the following values Select one: O a. 0.707 and 0.807 O b. 0.631 and 0.692 O c. 0.2356 and 0.5625 O d. 0.5215 and 0.5625 Previous page Next page 1 Assignmen

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

In the common mode, ..... ..... ..... Select one: a. the output signal are in-phase b. an identical signal appears on both the inputs c. the outputs are connected together d. both inputs are grounded
Boost Converter Design A boost converter is required to have an output voltage of 8 V and supply a load current of 1 A. The input voltage varies from 2.7 to 4.2 V. A control circuit adjusts the duty ratio to keep the output voltage constant. Select the switching frequency. Determine a value for the inductor such that the variation in inductor current is no more than 40 percent of the average inductor current for all operating conditions. Determine a value of an ideal capacitor such that the output voltage ripple is no more than 2 percent. Determine the maximum capacitor equivalent series resistance for a 2 percent ripple.
A boost converter is required to have an output voltage of 8 V and supply a load current of 1 A. The input voltage varies from 2.7 to 4.2 V. A control circuit adjusts the duty ratio to keep the output voltage constant. Select the switching frequency. Determine a value for the inductor such that the variation in inductor current is no more than 40 percent of the average inductor current for all operating conditions. Determine a value of an ideal capacitor such that the output voltage ripple is no more than 2 percent. Determine the maximum capacitor equivalent series resistance for a 2 percent ripple.
Part 1) Consider a step down converter with a resistive load. It is supplied by a DC power source of magnitude Vs = 160 V. The switching period is 0.25 ms and the duty cycle k is first set to 0.5. The load is resistive with R=10 Ohms. The critical value of L and the critical value of C are equal to: a. 0.625mH and 0.392uF b. 0.625mH and 0.196uF c. 0.312mH and 0.196uF d. None of these Part2) Now consider the same given but the load is an inductive load with R=10 Ohms and L=10 mH. The switch is ideal. Calculate The RMS load current Io and the RMS converter current Ir are equal to: Select one: a. 5A and 3.54A b. None of these c. 8A and 5.66A d. 12.5A and 8.84A
d- The ripple frequency in the output voltage of single-phase half-controlled bridge AC/DC converter is ................ when a > 60°. 1- 3f, 2- 6f, 3- 2f, 4- f, 5- None of previous. e- The integrator in the firing circuit of 1-phase bridge AC/DC converter is necessary to have firing angle range. 1-0-90°, 2-0-120°, 3-0-180°, 4-0-360°, 5- None of previous. f The harmonic contents in an inverter can be reduced through the use of modified............ PWM. 1- Voltage, 2- Full, 3- Reduced, 4- Commutation, 5- None of previous. g- Continuous current operation in step-down chopper is gained when.............. 1- txT, 1-√ √LC, 2-2√ √LC, 3-0.5√ √LmC, j- The time available to turn-off thyristor in load-commutated chopper is 3- 2E²cf, 4-E²Cf, 5- None of previous. lo 1-2EC lo' 2-50 EC
A single-phase full-wave converter in the figure below is supplied with a 120-V, 60-Hz source. The load is highly inductive and the load current is continuous and free of ripples. The electromotive force is neglected (E = 0) and the resistance has a value of R = 10 2. The average output voltage is 85% of the maximum possible average output voltage. The delay angle would be equal to: Select one: 81.8° O b. 31.8° O c 67.8° O d. 51.8° AT₁ AT, R L +7=4₂ W
signal subject notice for 2 b(i) use integration way and prove the answer with graph
A single-phase full-wave converter in the figure below is supplied with a 120-V, 60-Hz source. The load is highly inductive and the load current is continuous and free of ripples. The electromotive force is neglected (E 0) and the resistance has a value of R = 10 Q. The delay angle is equal to 31.8°. The average output current is 9.18A and the nth harmonic component is expressed as below. The harmonic factor (known as THD) would be equal to: R 2. vZ.1. Ir = Vo n. T +Yi, = I, E Select one: O a. 58.3% Ob. 48.3% O C. 78.3% Od. 68.3%
4: Design a buck converter to produce an output voltage of 18 V across a 10-_ load resistor. The output voltage ripple must not exceed 0.5 percent. The dc supply is 48 V. Design for continuous inductor current. Specify the duty ratio, the switching frequency, the values of the inductor and capacitor, the peak voltage rating of each device, and the rms current in the inductor and capacitor. Assume ideal components.
C'uk Converter Design A C'uk converter has an input of 12 V and is to have an output of - 24 V supplying a 60 W load. Select the duty ratio, the switching frequency, the inductor sizes such that the change in inductor currents is no more than 12 percent of the average inductor current, the output ripple voltage is no more than 1.5 percent, and the ripple voltage across C1 is no more than 3 percent.
What is the average value of output voltage, if the ON time of a step up chopper is 0.2 times the total time, and the source voltage of V,? a. 0.2 Vs O b. 0.8 Vs O c. 1.25 Vs d. 2.5 Vs
Given the figure below, find the following: a. Form factor b. Peak factor