A boost converter is required to have an output voltage of 8 V and supply a load current of 1 A. The input voltage varies from 2.7 to 4.2 V. A control circuit adjusts the duty ratio o keep the output voltage constant. Select the switching frequency. Determine a value for he inductor such that the variation in inductor current is no more than 40 percent of he average inductor current for all operating conditions. Determine a value of an ideal capacitor such that the output voltage ripple is no more than 2 percent. Determine the maximum capacitor equivalent series resistance for a 2 percent ripple.

A boost converter is required to have an output voltage of 8 V and supply a load current of 1 A. The input voltage varies from 2.7 to 4.2 V. A control circuit adjusts the duty ratio o keep the output voltage constant. Select the switching frequency. Determine a value for he inductor such that the variation in inductor current is no more than 40 percent of he average inductor current for all operating conditions. Determine a value of an ideal capacitor such that the output voltage ripple is no more than 2 percent. Determine the maximum capacitor equivalent series resistance for a 2 percent ripple.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q1) The buck converter has an input of 50 V and an output of 25 V. The switching frequency is 100 kHz, and the output power to a load resistor is 125 W. Determine: (a) the duty ratio. (b) the value of inductance to limit the peak inductor current to 6.25 A. (c) the value of capacitance to limit the output voltage ripple to 0.5 percent.
5 Listed are some of the uses of capacitors except: A. couples AC B. bypassing a shunt load C. signal amplification D. filters pulsating DC
A step down converter is feeding an inductive load with R-10 Ohms, L15 mH and E-1sV. The supply is Vs-200v, the switching frequency is 10 kHz and the duty cycle is k-0.5. The maximum peak to peak ripple current in the load is equal to 0.34A. The erage load current la would be equal to: Select one: a. 8.5A O b. 18A Oc 11A O d. None of these
Calculate the peak-to-peak inductor current ripple (in amperes) of a Buck converter assuming it operates in continuous current conduction mode. Circuit parameters are: Input voltage Vdc = 38 V, output voltage Vo = 17 V, PWM frequency fpwm = 50 kHz, inductor value 328 µH and capacitor value C = 10 µF. is S iL L I₂ Vac VA D VL ic C R₁ Please specify your answer in units of A to 2 decimal places. V
The inductor current of a buck-boost converter is shown in the figure. The minimum inductor current is zero and the peak value is 5A. The load resistor 5 A value is equal to R=702 Assume that the output voltage ripple is 1%. All components are ideal. Determine. a) Duty ratio. b) Output voltage. c) Input voltage d) Inductor value e) Capacitor value. 12μ 20μ 32μ 40μ t,sec
An unipolar PWM full bridge circuit has a Vr.rms of 125V at a duty cycle D1 of 0.7. What is Vd? What is Vo.rms?
C'uk Converter Design A C'uk converter has an input of 12 V and is to have an output of - 24 V supplying a 60 W load. Select the duty ratio, the switching frequency, the inductor sizes such that the change in inductor currents is no more than 12 percent of the average inductor current, the output ripple voltage is no more than 1.5 percent, and the ripple voltage across C1 is no more than 3 percent.
What voltage is boosted at the output of a multiplier.Choices: average, rms, peak, or instantaneous Which assumption is not used in the analysis of multipliers?Choices: a capacitor will not discharge, start with the cycle of the source that will forward bias the nearest diode, the output will always be multiplied, or a single diode is forward biased at a time A voltage multiplierChoices: multiplies the output voltage, has very high voltage and low current ,can employ inductors, or may not have equal numbers of diodes and capacitors A voltage regulator maintains constant voltage at the load regardless of variations atChoices: the input and output, the load, source, or in the environment Between a lower percent regulation and a higher one, which is better?Choices: lower or higher
A clipper circuit based on diodes are simple way to modify waveform in mechatronics. Assume that the two diodes shown in the circuit below are ideal diodes. If the input voltage in the circuit is a 1 kHz sinusoid with peak amplitude of 8V, sketch the Vaue (t). 10 k. 8V 10 kN. D2 RL Vourlt) Vin= Vin(t) Ims D1 6V -8V 4V Page | 1
Design a Cuk converter that has an input of 25V and the output of -30V. The load is 60W. Specify the duty ratio, switching frequency, inductor values and capacitor values. The maximum change in inductor currents must be 20 percent of the average currents. The ripple voltage across capacitor C1 must be less than 5 percent, and the output ripple voltage must be less than 1 percent.
1. Which of the following answers best describes discontinuous conduction mode? A. The inductor voltage ripple goes negative B. The inductor current ripple stays positive C. The inductor current ripple falls to zero D. The output current ripple falls to zero
An R-L load is connected to a 250 V, 400 Hz step down dc converter. The average load current is 100 A. The load resistance is 0.5 Ohm. The allowed ripple limit is 15%. The minimum value of inductor to limit the maximum ripple current is: