A 50-mm diameter solid shaft, with a length of 1 meter, is supported at one end and free in the other end. Determine the maximum allowable torque for each material if the angle of twist is not to exceed 6º. Remember to consider both the maximum shear stress and the angle of twist. MATERIAL MODULUS OF RIGIDITY MAXIMUM SHEAR STRESS TORQUE Aluminum 26 GPa 207 MPa Steel 79 GPa 75 MPa Titanium 44 GPa 760 MPa

A 50-mm diameter solid shaft, with a length of 1 meter, is supported at one end and free in the other end. Determine the maximum allowable torque for each material if the angle of twist is not to exceed 6º. Remember to consider both the maximum shear stress and the angle of twist. MATERIAL MODULUS OF RIGIDITY MAXIMUM SHEAR STRESS TORQUE Aluminum 26 GPa 207 MPa Steel 79 GPa 75 MPa Titanium 44 GPa 760 MPa

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.3.12P: A propeller shaft for a small yacht is made of a solid steel bar 104 mm in diameter. The allowable...

See similar textbooks

Similar questions

A stepped shaft ABC consisting of two solid, circular segments is subjected to torques T}and T2acting in opposite directions, as shown in the figure. The larger segment of the shaft has a diameter of dv- 2.25 in. and a length Lt= 30 in.; the smaller segment has a diameter d2— 1.75 in. and a length L, = 20 in. The torques are T, = 21,000 lb-in. and fz=10.000 lb-in. (a) Find reaction torque TAat support A. (b) Find the internal torque T(x) at two locations: x = L1/2 and x = L1+ L2/2. Show these internal torques on properly drawn free-body diagrams (FBDs).
A propeller shaft for a small yacht is made of a solid steel bar 104 mm in diameter. The allowable stress in shear is 48 MPa, and the allowable rate of twist is 2.0° in 3.5 meters. (a) Assuming that the shear modulus of elasticity is G = 80 GPa, determine the maximum torque that can be applied to the shaft. (b) Repeat part (a) if the shaft is now hollow with an inner diameter of 5d18. Compare values to corresponding values from part (a).
A hollow steel shaft is stressed to 55 MPa by a torque of 135600Nm. Determine the outside diameter in mm if the inside diameter is 2/3 of the outside diameter and G = 83 GPa.
2: If the permissible shear stress of a solid shaft is of 70MPa, the torque angle between two cross sections separated 2.5m does not exceed 3°, the applied torque is of 1400N.m and G=11Gpa a. Determine the required diameter in function of the shear stress b. Determine the required diameter in function of the angle of twist
A steel shaft with a length of 3.00 m. One meter of the steel is contained in a brass tube and firmly attached. The diameter d1 = 70 mm and the diameter d2 = 90 mm. Brass G = 39GPa and steel G = 77.20 GPa. Determine: The torque that can be applied if the deformation at one end is 10 degrees. Answer: T = 8.64 kN – m The torque that can be applied if the maximum shear stress in brass is 70MPa and in steel is 110MPa. Answer: T = 6.352 kN – m Recommendation: analyze by segments. The first segment is only brass, then the composite part between brass and steel, and the last part only steel. In the composite segment, use only one material. In this same segment, equalize the deformations.
Bearing stress 4. Please provide proper discussion and illustration also complete solution and clear solution please thank you Determine the length of a square key to be used for a 3.73 kW, 1800 rpm electric motor if the motor shaft diameter is 35 mm and the width of the key is approximately one-fourth of the shaft diameter. The allowable shearing stress on the key is 2.45 MPa
A compound steel (G= 70 GPa) shaft consists of a solid 59-mm-diameter segment (1) and a solid 39-mm- diameter segment (2). The allowable shear stress of the steel is 76 MPa, and the maximum rotation angle at the free end of the compound shaft must be limited to Pcs 4.6°. Assume ₁-0.6 m and £₂-1.0 m. Determine the magnitude of the largest torque Te that may be applied at C. Express your answer in N-m rounded to three significant digits. L₁ (1) B (2) L2 Tc C X
A solid brass shaft is loaded as shown below by two torques TB- segments are LAB = 700 mm and LBC 600 mm. A dBc = dAB mm LAB mm B Com dBC For brass, G = 41 GPa. Neglect the effect of any stress concentrations. LBC Determine the smallest diameters dAB and dBC for which an allowable shear stress of 50 MPa is not exceeded. Express each diameter as an integer in units of mm. dAB To 1100 Nm and Tc = 300 Nm. The lengths of the two Determine the magnitude of the total angle of twist in the shaft caused by the two applied torques for the diameters found previously Express your result in units of radians with five decimal places of accuracy. PAC = rad
The hollow rod shown below is 2.99 meters long and is subjected to a torque of 988 Nm at end B. The diameter of the rod is 30 mm and has a wall thickness of 5 mm. The shear modulus of the material is 80 GPa, calculate the angle of twist in radians at B. TNm B meters
A solid bar of circular cross section has a diameter of 40mm and length of 1300mm. G=80GPa and torque applied at both ends is 340 N.m. Determine the angle of rotation in radians.
A compound shaft consists of an outside tube (1) and an inner tub (2) that are fully connected together. Determine the maximun allowable torque that could be applied to the compound shaft if the allowable shear stress in the outer shaft is Tall, 1 = 89 MPa, and the allowable shear stress in the inner shaft is Tall,2 = 62 MPa.[G₁: 39 GPa, G₂ = 16 GPa, d₁ = 102 mm, d₂ = 87 mm, d3 = 55 mm] Tube (1) Tube (2) Answer: d3 d₂ d₁ Tube (1) Tube (2) kN.m
A 3-m long thin-walled tube has an equilateral triangular cross-section with a constant thickness of 10 mm. If each side of the triangle is 200 mm measured at the median line and the applied torque is 40 kN-m, what is the angle of twist in degrees? (Use G=70 GPa) (Round your answer to 3 decimal places)