A compound shaft consists of an outside tube (1) and an inner tube (2) that are fully connected together. Determine the maximun allowable torque that could be applied to the compound shaft if the allowable shear stress in the outer shaft is Tall, 1 = 89 MPa, and the allowable shear stress in the inner shaft is Tall,2 = 62 MPa.[G₁ : 39 GPa, G₂ = 16 GPa, d₁ = 102 mm, d₂ = 87 mm, d3 = 55 mm] Tube (1) Tube (2) O dz

A compound shaft consists of an outside tube (1) and an inner tube (2) that are fully connected together. Determine the maximun allowable torque that could be applied to the compound shaft if the allowable shear stress in the outer shaft is Tall, 1 = 89 MPa, and the allowable shear stress in the inner shaft is Tall,2 = 62 MPa.[G₁ : 39 GPa, G₂ = 16 GPa, d₁ = 102 mm, d₂ = 87 mm, d3 = 55 mm] Tube (1) Tube (2) O dz

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.7.12P

See similar textbooks

Similar questions

A stepped shaft ABC consisting of two solid, circular segments is subjected to torques T}and T2acting in opposite directions, as shown in the figure. The larger segment of the shaft has a diameter of dv- 2.25 in. and a length Lt= 30 in.; the smaller segment has a diameter d2— 1.75 in. and a length L, = 20 in. The torques are T, = 21,000 lb-in. and fz=10.000 lb-in. (a) Find reaction torque TAat support A. (b) Find the internal torque T(x) at two locations: x = L1/2 and x = L1+ L2/2. Show these internal torques on properly drawn free-body diagrams (FBDs).
A compound shaft consists of an outside tube (1) and an inner tube (2) that are fully connected together. Determine the maximum allowable torque that could be applied to the compound shaft if the allowable shear stress in the outer shaft is Tall, 1 = 83 MPa, and the allowable shear stress in the inner shaft is Tall,2= 62 MPa.[G₁ = 32 GPa, G₂ = 22 GPa, d₁ = 101 mm, d₂ = 83 mm, d3= 56 mm] Answer: dz d₂ d₁ Tube (1) Tube (2) kN.m
A compound shaft consists of two pipe segments. Segment (1) has an outside diameter of 216 mm and a wall thickness of 10 mm. Segment (2) has an outside diameter of 124 mm and a wall thickness of 14 mm. The shaft is subjected to torques Tg = 34 kN-m and Tc = 15 kN-m, which act in the directions shown. Determine the maximum shear stress magnitude in segment (2). (1) O 62.5 MPa O 80.7 MPa O 85.3 MPa O 73.5 MPa O 66.2 MPa
A compound shaft consists of two pipe segments. Segment (1) has an outside diameter of 212 mm and a wall thickness of 9 mm. Segment (2) has an outside diameter of 139 mm and a wall thickness of 11 mm. The shaft is subjected to torques TB = 47 kN-m and Tc = 24 kN-m, which act in the directions shown. Determine the maximum shear stress magnitudes 7₁, 72 in each shaft segment. Answers: T1 = i T2 = i (1) (2) MPa. MPa.
A turbine rotor is mounted on a stepped shaft that is fixed at both ends as shown in The torsional stiffnesses of the two segments of the shaft are given by k = 3,000 N-m/rad and k2 = 4,000 N-m/rad. The turbine generates a harmonic torque given by M(1) = Mo cos wt about the shaft axis with M, = 200 N-m and w = 500 rad/s. The mass moment of inertia of the rotor about the shaft axis is J, = 0.05 kg-m?. Assuming the equivalent torsional damping constant of the system as e, = 2.5 N-m-s/rad, determine the steady-state response of the rotor, 0(1). O(1) M(1) = Mg cos etr %3! Turbine rotor, Jo
The shaft ABC shown in the figure is drivenby a motor that delivers 300 kW at a rotational speedof 32 Hz. The gears at B and C take out 120 kW and180 kW, respectively. The lengths of the two parts ofthe shaft are L1 = 1.5 m and L2 = 0.9 m.Determine the required diameter d of the shaft ifthe allowable shear stress is 50 MPa, the allowableangle of twist between points A and C is 4.0°, andG = 75 GPa.
The shaft, is driven by pulley B from an electric motor. Another belt drivefrom pulley A is running a compressor. The belt tensions for pulley A are 1500 N and 600 N. The ratioof belt tensions for pulley B is 3.5. The diameter of pulley A is 150 mm and the diameter of pulley B is 480 mm. The allowable tensilestress for the shaft material is 170 MPa and the allowable shear stress is 85 MPa. Taking torsion andbending factors as 1.25 and 1.75 respectively, find the shaft diameter.Also find out the dimensions for a hollow shaft with outside diameter limited to 30 mm. Compare theweights of the two shafts. [Ans. 30 mm ; 24 mm ; 1.82 Given Length CD=350mm Length AB=150mm Length BD=100mm The total length is CD =350
A turbine rotor is mounted on a stepped shaft that is fixed at both ends as shown in The torsional stiffnesses of the two segments of the shaft are given by k = 3.000 N-m/rad and k2 = 4,000 N-m/rad. The turbine generates a hamonic torque given by M(1) = Mo cos ot about the shaft axis with Mg = 200 N-m and as = 500 rad/s. The mass moment of inertia of the rotor about the shaft axis is h = 0.05 kg-m. Assuming the equivalent tosional damping constant of the system as e, = 2.5 N-m-s/rad, determine the steady-state response of the rotor, 6(1). ka M() = Ma cos e Turbine rotor, Jo A 50-kg turbine is mounted on four parallel springs, each of stiffness of 3 x 10° N/m When the machine operates at 40 Hz. its steady-state amplitude is observed as 1.8 mm What is the magnitude of the excitation? Given m = 50 kg. k = 3x 10 Nm. e = 40 Hz. X= 1.8 mm Find: Fe
The steel shaft of a socket wrench has adiameter of 8.0 mm and a length of 200 mm (seefigure).If the allowable stress in shear is 60 MPa, whatis the maximum permissible torque Tmax that may beexerted with the wrench?Through what angle f (in degrees) will the shafttwist under the action of the maximum torque?(Assume G = 78 GPa and disregard any bending ofthe shaft.)
Q3: The shaft consists of three concentric tubes, each made from the same material and having inner and outer radii as given below. Length of shaft is 2m. One end is fixed to the wall and to the other end a disc is attached. If a torque ofT =800 N.m is applied at the disc end, determine the maximum shear stress in the shaft. 1. Inner tube: r¡ = 20mm, r, = 25 mm 2. Center tube: r; = 26 mm, r, = 30 mm 3. Outer tube: r; = 32mm, r, = 38mm
A compound shaft consists of two pipe segments. Segment (1) has an outside diameter of 200 mm and a wall thickness of 10 mm. Segment (2) has an outside diameter of 150 mm and a wall thickness of 10 mm. The shaft is subjected to torques TB = 42 kN-m and TC = 18 kN-m, which act in the directions shown in Figure. Determine the maximum shear stress magnitude in Segment (2). J1= 54019686 mm4J23D 21551281 mm4 TB Tc (2) O 88.8 MPa 62.3 MPa O 44.4 MPa 124 6 MPa
A fixed-end shaft is subjected to torques T1 (Nm) and T2 (Nm) as shown in the figure. If the shear modulus of elasticity is Gahat= 20 GPa, and shaft diameters are D, (mm) and D2 (mm) determine the angle of twist at point C, ØCIA- D1=100mm D2=30mm T1=800NM T2=200NM D1=100mm T(Nm) B D2=30mm |T;(Nm) A L=300mm Section for point A =900mm Section for points B and C Results Table ОСА (rad.)-