Figure 24. Consider the circuit in Figure 3. D1 is Gallium arsenideand D2 is Silicon, each has a forward resistance of 500.Determine the following:a. The states of D1 and D2. Explain.b. Current 11 through R1c. Current 12 through R2d. Current 13 through R3e. Voltage VoLiv HiltR11092V112V(+2)V1D11V50Hz0°1D1R21592Figure 35. Do number 4 again, but this time reverse both thepositions of D1 and D2.6. Consider the circuit in Figure 4.a. Calculate the voltage across R3 during the positivehalf cycle of the source voltage V1.b. Calculate the voltage across R3 during the negativehalf cycle of the source voltage V1.c. Sketch the waveform of the voltage across R3.R11kQV29VD2R310092R21k92D2VoR31k92

As per our company guidelines we are supposed to answer only first question kindly repost the other…

4. Consider the circuit in Figure 3. D1 is Gallium arsenide and D2 is Silicon, each has a forward resistance of 500. Determine the following: a. The states of D1 and D2. Explain. b. Current 11 through R1 c. Current 12 through R2 d. Current 13 through R3 e. Voltage Vo R1 1092 V1 12V D1 R2 1592 V2 9V R3 10092 D2 Vo

4. Consider the circuit in Figure 3. D1 is Gallium arsenide and D2 is Silicon, each has a forward resistance of 500. Determine the following: a. The states of D1 and D2. Explain. b. Current 11 through R1 c. Current 12 through R2 d. Current 13 through R3 e. Voltage Vo R1 1092 V1 12V D1 R2 1592 V2 9V R3 10092 D2 Vo

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

How is a solid-state diode tested? Explain.
What is CEMF?
What are the states for diodes in the figure below? D1 D2 4 k2 10 V 10 V O a. D1 off D2 on O b. D1 off D2 off O c. D1 on D2 off O d. D1 on D2 on
a. If you do not go completely around the loop when applying Kirchhoff’s voltage law, then the algebraic sum of the voltages cannot be determined the algebraic sum of the voltages will always be positive the algebraic sum of the voltages will always be negative the algebraic sum is the voltage between the start and finish points b. A p -type semiconductor is a semiconductor doped with impurity atoms whose electron valence is +4 pentavalent impurity atoms trivalent impurity atoms
ii) Analyse the circuit shown in below Figure. 2, assume diodes as silicon diode. Calculate: a. Vout b. IR3 c. Ip2 VCC 16V D1 D4 V3 10 V R1 2.2kQ D5 D2 Vout R3 2.8kQ IR3 Ip2 R2 4.7 kQ D3 V1 2.2 V V2 15V
5 For the following circuit: a) Draw a table to mention the names, the states (ON/OFF) and turn on voltages for all the diodes of the circuit. (V = 3.5V for D3) and draw the equivalent circuit. b) Find the voltage across R1, R2, R3 c) Find the current through D1 , Dz , D3 and D4 D1 Si R2 D2 5002 Si R1 7502 R3 D3 D4 V1 1kn Blue GaAs 10v
Q*: Calculate the current through 48 Q resistor in the circuit shown in Figure(i).Assume the diodes to be of silicon and forward resistance of each diode is 1 Q. D D2 48 2 ww 10 V= D4 D3 (i)
Which of the following circuit elements is a typical example of semiconductor material? Lütfen birini seçin: O A. Capacitor O B. Inductor O C. Resistor O D. npn BJT O E. Voltage source
for the circuit shown in the figure, plot the output voltage waveform and present the resolution in sections considering that the diodes are silicon. D4 23 100k D6 100k 24 DIODE SV Vs4 [v] 20 Vo -20
For the circuit below, assume the diodes operate with a constant voltage drop of .7V, find Vx, Vy, VD4 and ID2. 15V 15V Allt V1 V2 R1 1k IDC 1mA Vx R2 2k ww D1N4002 Vy D1N4002 7D1 D1N4002 D2 D3 R3 1k D4 D1N4002
In the circuit shown in the figure, draw vx and v0 with a scale according to the input voltages. note = R1 = 10Kohm R2 = 1kohm R3 = 1Kohm, threshold voltages of diodes shall be VE = 0.7V.
Draw vx and v0 according to the input voltages in the circuit shown in the figure. note = R1 = 10Kohm R2 = 1kohm R3 = 1Kohm, the threshold voltages of diodes will be VE = 0.7V.