1. A lead pipe has 2 cm inside diameter, 3 cm outer diameter, length of 130 cm. Liquid water at4°C flows through the pipe with a bulk velocity of 2.50 km/hr. Air is blown around theoutside of the pipe at 20 deg C. The inside wall of the said pipe has a temperature of 8 degCelsius.Find:a. Overall heat coefficient (U) based on outside surface areab. Prandtl (Pr) and Reynolds (Re) numbers based on classification of flow

Answered: Image /qna-images/answer/661d0c64-c57b-42ef-92a1-1e90b28ed1ef.jpg

Answered: 1. A lead pipe has 2 cm inside…

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter10: Heat Exchangers

Section: Chapter Questions

Problem 10.28P

See similar textbooks

Similar questions

Example: A 1.0 kw heater is Constructed ofaglass plte with an electrically condcting film which produčes' a Constant hent flux . The plate is 60x 60 cm and placed in an air sebeetote stream at 27c ,d atm with Uo=5 m/s. Calculate the average temp. difference along the plate, and the difference at the trailing edge.
K spherical shaped vessel of 1.2 m diameter is 100 mm thick. Find the rate of heat leakage, if the temperature difference between the inner and outer surfaces is 200° C. Thermal conductivity of material is 0.3 kJ /mh°C.
consider a flow of water in a cylinder maintained at constant temperature of hundred degree Celsius the diameter of the cylinder is 15 and the length of the tube is 6 metre the inlet and outlet temperature of the water is TI equal to 15 degree Celsius and equal 57 degrees celsius find the average heat transfer Coefficient associated with the flow of water mass flow rate is 2.25 kilogram per second and cp=4.178KJ/aKg.K
What is the formula to solve h1 and h2 (heat transfer coefficient)here? h1 (water) h2 (air).
Water at a temperature of 20 oC with a mass flow rate of 0.015 kg/s enters the pipe 2.5 cm in diameter with a uniform surface temperature of 90 oC. a) Determine the length of the thermal inlet region, Lt.b) If it is assumed that the flow is hydrodynamically and thermally formed, calculate the convection heat transfer coefficient and the length of the pipe required to heat the water to 70 oC.c) What is the rate of heat transfer to the water?d) Calculate the friction factor and pressure drop.
(B) Air is flowing through a thick walled copper pipe that can be considered to be isothermal at 450 degrees C Inner diameter of the pipe is 3cm and 0 9m inng Air enters at 30 degrees C and exit buik temperature is 95 degrees C. if the length is now doubled assuming air mass flow rate and heat transfer coefficient remain the same in both iengths what is the new bulk temperature at the exit?
You are designing a pin-style heatsink for forced cooling of an IC. A small fan blows RT air into the heatsink at about 2.3 ? ? . The aluminum pins are 2mm in diameter and have a constant surface temperature of 120°?. The heatsink is 100mm x 100mm and the pins have an inline arrangement with a transverse pitch of 4mm and a longitudinal pitch of 6mm. What is the total heat dissipation of this heatsink? The pins are 30mm high. Note RT=25 celsius
Problem 3: RT Air is flowing over an aluminum pipe (20mm OD, 5mm ID) at 6-. The pipe has 10mm thick fiberglass insulation on it. The pipe is carrying a hot air supply Thair 80°C for use in a chemical m3 process at a rate of Qhair 0.04 What is the heat rate from the hot air to the ambient air?
Using a 130 cm- long lead pipe with 2 cm inside diameter, a liquid water is transferred at 4 degrees Celsius. Its outside diameter measures 3 cm and the temperature of air outside is 20-deg C. The inside wall of the said pipe has a temperature of 8 degrees Celsius. Solve for: Outside area as basis, find (U) overall heat transfer coefficient
Water going into a pipe with a tempeture of T1 and going out T2 . ambient tempeture is T0. flow rate q. Develop an expression for T2 ( based on heat transfer) Length of the pipe Lh0 - convective heat transfer coefficient of the airhW -convective heat transfer coefficient of the waterk- pipe thermal conductivity (W/m·K)d – pipe diameter Use any other varilable that you need and can be found online easily .
A steam condenser is made of brass tubes,in., 14 gage. There are 150 tubes per pass. The cooling water flows at the rate of 1.52 m/s, entering at 25°C and leaving at 50°C. The condensing heat transfer coefficient is known to be 10,200 W/m²-°C and the inside tube surface coefficient is 6800 W/m²-°C. Steam is being condensed at 77°C. The tubes are not to exceed 3 m in length. Find the number of tube passes and the length of the tubes.
A thick-walled cylinder tubing of hard rubber having an inside radius of 20mm is being used as temporary cooling coil in a bath. Ice water is flowing rapidly through inside tube and the inside wall temperature is 274.9K. The outside surface temperature is 297.1K. A total of 14.65W must be removed from the bath by cooling coil. How many m of tubing are required?

SEE MORE QUESTIONS

Recommended textbooks for you

Principles of Heat Transfer (Activate Learning wi…

Mechanical Engineering

ISBN:

9781305387102

Author:

Kreith, Frank; Manglik, Raj M.

Publisher:

Cengage Learning