A thick-walled cylinder tubing of hard rubber having an inside radius of 20mm is being used as temporary cooling coil in a bath. Ice water is flowing rapidly through inside tube and the inside wall temperature is 274.9K. The outside surface temperature is 297.1K. A total of 14.65W must be removed from the bath by cooling coil. How many m of tubing are required?

A thick-walled cylinder tubing of hard rubber having an inside radius of 20mm is being used as temporary cooling coil in a bath. Ice water is flowing rapidly through inside tube and the inside wall temperature is 274.9K. The outside surface temperature is 297.1K. A total of 14.65W must be removed from the bath by cooling coil. How many m of tubing are required?

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter40: Typical Operating Conditions

Section: Chapter Questions

Problem 9RQ: The evaporator design temperature may in some cases operate at a slightly ____(higher or lower)...

See similar textbooks

Similar questions

* It required to design a ducting system to condition the building shown in figure (1). The uantity of outdoor is (20%) of supply air. Using information in table, find 1- The sensible and latent load for cooling coil. 2- The quantity and condition of supply air to each place. 3- By using equal pressure drop method, design the rectangular ducting system with maximum height side (600mm). 4- Illustrate the all process on psychometric chart. Outdoor 45 °C db & 30% RH Out let type Celling conditioning indoor conditioning 24 °C db & 50% RH diffuser Number of diffuser 2 for each place 15 kpa 10 kpa 15 kpa By pass factor Apparatus dew point 9°C Ap losses diffuser Ap losses filter Ap losses coil 0.15 R/w 1.5 6m 6m 6m Room (1) Room (2) Room (3) 4m RSH=8KW RSH=6KW RSH=8KW RLH=2KW RLH=1KW RLH=2KW 2m AHU Mechanical Room (4) RSH=20KW 4m Room RLH=3KW 4m 14m
* It required to design a ducting system to condition the building shown in figure (1). The uantity of outdoor is (20%) of supply air. Using information in table, find 1- The sensible and latent load for cooling coil. 2- The quantity and condition of supply air to each place. 3- By using equal pressure drop method, design the rectangular ducting system with maximum height side (600mm). 4- Illustrate the all process on psychometric chart. Outdoor 45 °C db & 30% RH Out let type Celling conditioning indoor conditioning 24 °C db & 50% RH diffuser Number of diffuser 2 for each place 15 kpa 10 kpa 15 kpa By pass factor Apparatus dew point 9°C Ap losses diffuser Ap losses filter Ap losses coil 0.15 R/w 1.5 бm бm бm Room (1) Room (2) RSH=6KW Room (3) 4m RSH=8KW RSH=8KW RLH=2KW RLH=1KW RLH=2KW 2m AHU Mechanical Room (4) RSH=20KW 4m Room RLH=3KW 4m 14m
How many tons of refrigeration are required to produce 10 metric tons of ice per day at -10 °C from raw water at 22 °C if miscellaneous losses are 15% of the chilling and freezing load? 3.
A Horizontal Return Fire-Tube Boiler in 60 inches in diameter, 16 ft long, has 70 tubes that are 3 inches O.D with 0.109-inch tube thickness. If was found that the boiler’s steam rate is 0.50 kg/s and the factor of evaporation is 1.25. What is the Percent (%) Rating of the Boiler?
A saturated steam at 410K is being transported in a pipeline (brass drawing tubing) at a rate of 1 grams/second. Pipe has inside diameter of 0.025 m . The tube is 100m long. The pressure at the entrance is 80kPa. (use Perry's Handbook for the properties and constants) R = 8314J/kgmol.K; MW=18.02g/mol What is the a.) value of G in kg/s.m2? b.)value of friction factor? 3 significant figures c.)the % of pressure drop? d.)the outlet pressure? e.) compressible or not?
A four-effect evaporator is being considered for concentratinga fruit juice that has no appreciable boiling-point elevation.Steam is available at 143.27 kPa, and the boiling point of the product in the fourth effect is 45°C. The overall heat-transfer coeffi cients are 3000 W/(m 2 °C) in the fi rst effect, 2500W/(m2 °C) in the second effect, 2100W/(m2°C) in thethird effect, and 1800W/(m2°C) in the fourth effect. Calculatethe boiling-point temperatures of the product in the fi rst,second, and third effects. Assume the heating areas in all theeffects are equal to 50m2 each. The mass fl ow rate of steam tothe fi rst effect is 2400kg/h, the feed rate to the fi rst effect of 5%total solids fl uid is 15,000kg/h, the concentrated product fromthe fi rst effect leaves at 6.25% total solids, and the concentrationof product leaving the second effect is 8.82% total solids. Make it in the form of an example solution spreadsheet .....
48. Water is flowing in a smooth pipe of diameter D. A section of this pipe hav- ing a length of L is heated. Water at the inlet to the heated section has a tempera- ture of Tŋ. Water temperature at the exit of the heated section is Tp. The heated section of the pipe wall is maintained at a constant heat flux so that a constant temperature difference of AT, = T, – T, exists between the wall and the bulk wa- ter temperature. Show that for turbulent flow in the pipe and a specified heated length and pipe diameter, water temperature at the exit of the heated section is given by: 402 0.6 Pr T52 =Tf +0.0876 L AT DO.8 0.2 m
A PCB is cooled by a 40mmL x 40mmW x 20mmL aluminum block heatsink. If the top and bottom surface of the aluminum heatsink run 45degC and 85degC respectively, what is the heat rate through the aluminum block?
3. Solar radiation heats the surface after sunrise, and the resulting heat flux F to the atmosphere is approximated by 2T(t – tnoon) F = F cos 6 a.m. < t< 6 p.m. max At
Bourdon tube is also referred to as an
6- The following reading were taken during a test on a surface condenser: Mean condenser temperature = 35°C Hot well temperature = 30°C Condenser vacuum = 69 cm Hg Barometer reading = 76cmHg Condensation rate = 16 kg/min Cooling water temperature inter = 20 °C Cooling water temperature outlet = 32.5 °C Flow rate being = 37500 kg/h Calculate: a- mass of air present per cubic meter of condenser b- quality of steam at condenser inlet c- vacuum efficiency d- condenser efficiency (condenser heat transfer effeteness)
AS& Heat Transfer in Steam Heater Water at an average of 70°F is fiowing in a 2-in. steel pipe, schedule 40. Steam at 220°F is condensing on the outside of the pipe. The con vective coefficient for the water inside the pipe is A = 500 btu/h ft2.°F and the con- densing steam cocfficient on the outside is h = 1500 (a) Calculate the heat loss per unit length of1 ft of pipe using resistances. (b) Repcat, using the overall based on the inside area Ap (c) Repeat, using U 13.2- Ans. (a)q= 26 710 btu/h (7.828 kW). (b) Uj = 329.1 btu/h-ft2."F (1869 W/m2. K), (c) U.= 286.4 btu/h ft2.°F (1626 W/m2. K)