Automotive Technology: A Systems Approach (MindTap Course List)
6th Edition
ISBN: 9781133612315
Author: Jack Erjavec, Rob Thompson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 45, Problem 4ASRQ
Technician A says that replacement wheel rims should be the same as the original equipment wheels in load capacity, offset, width, diameter, and mounting configuration. Technician B says that if wheels are installed that have a different stock width or diameter, make sure to use a tire that has the same overall width as the original tires. Otherwise the vehicle’s wheel-speed sensors, speedometer, antiock brake system, and many other systems will be affected. Who is correct?
a. Technician A only
b. Technician B only
c. Both A and B
Neither A nor B
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
Technician a says radial ply tires are more rigid in the sidewall area than bias ply tires. Technician b says the belts in a radial tire restrict tread motion during contact with the road thus improving tread life in traction. who is correct
Technician A says that on most vehicles, the wheel/tire assembly is considered sprung weight . Technician B says that low unsprung weight makes the vehicle handle better on irreg ular surfaces. Who is correct?
A vehicle with a direct TPMS just had all 4 tires replaced, yet the TPMS warning light is on. Technician A says this may be due to the tire tech damaging one of the sensors during tire replacement. Technician B says it may be caused by the tire tech damaging the wheel speed sensor during tire install. Who is correct?
Technician A
Technician B
Both Technician A and B
Neither Technician A or B
Chapter 45 Solutions
Automotive Technology: A Systems Approach (MindTap Course List)
Ch. 45 - List five things that could cause premature...Ch. 45 - Define lateral and radial runout.Ch. 45 - Prob. 3RQCh. 45 - Define dynamic and static wheel balance.Ch. 45 - Describe the proper procedure to seal a puncture...Ch. 45 - The rim offset is the vertical distance between...Ch. 45 - Prob. 7RQCh. 45 - True or False? All TPMS have a pressure sensor...Ch. 45 - A tire that wobbles from side-to-side is said to...Ch. 45 - A front tire has excessive wear on both edges of...
Ch. 45 - All of the following statements are correct...Ch. 45 - All of the following statements are correct...Ch. 45 - Which of the following statements about sidewall...Ch. 45 - All of these statements about improper wheel...Ch. 45 - Prob. 15RQCh. 45 - Technician A says that the front wheel bearings on...Ch. 45 - Technician A says that dynamic wheel imbalance...Ch. 45 - Technician A says that front bearing assembly...Ch. 45 - Technician A says that replacement wheel rims...Ch. 45 - Prob. 5ASRQCh. 45 - While choosing the correct tire for a vehicle:...Ch. 45 - Technician A says that on most vehicles, the...Ch. 45 - Prob. 8ASRQCh. 45 - Prob. 9ASRQCh. 45 - Prob. 10ASRQ
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- While discussing pull during braking: Technician A says that this can be caused by one tire being underinflated. Technician B says that a frozen wheel cylinder on one side of the car can cause this. Who is correct? Technician A only Technician B only Both A and B Neither A nor Barrow_forwardWhich of the following statements about sidewall markings is correct? a. The load index is given as a letter. b. The traction and temperature ratings are based on the speed rating of the tire. c. The tires recommended inflation pressure and load are indicated. d. The DOT code indicates when and where the tire was made.arrow_forwardHow does a technician determine the proper inflation for a vehicle's tires?arrow_forward
- Which of the following would NOT be cause for rejection when checking the tire condition? Any tire has a fabric break or cut exposing ply or cord or any tire is in contact with the body or frame. Any tire tread or recap is separated or any tire is flat. All of the statements shown are cause for rejection. Any tire has any bumps, bulges, or knots or is repaired with a boot or blowout patch.arrow_forwardA brake pad is found to be wearing more on one side than the other. Technician A says this is common in real world situations. Technician B says this is always a clear sign that there’s a problem. Who is correct? Technician A Technician B Both Technician A and B Neither Technician A or Barrow_forwardWhile performing a prealignment inspection: Technician A says that improper front-wheel bearing adjustment may affect wheel alignment angles. Technician B says that worn ball joints affect only the camber angle. Who is correct? Technician A only Technician B only Both A and B Neither A nor Barrow_forward
- While diagnosing the cause of noise from a transfer case: Technician A says that a probable cause is incorrect tire size. Technician B says that the most probable cause is a faulty bearing or gear. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardTechnician A says that the master cylinder should be bled before any individual wheel assembly. Technician B says that the bleeder screw should be closed before the brake pedal is released during manual bleeding of the system. Who is correct? Technician A only Technician B only Both A and B Neither A nor Barrow_forwardAll of the following statements are correct except?a. Tire inflation pressure directly affects traction.b. The recommended tire pressure for front andrear tires may be different.c. The recommended tire pressures are oftenlower than maximum pressures.d. The recommended tire pressure is moldedinto the sidewall of the tirearrow_forward
- Technician A says the front wheel bearings on a typical FWD car are sealed and non-adjustable. Technician B says the front wheel bearings on a typical FWD car are greaseable and adjustable. Who is correct?arrow_forwardIn what direction must the bottom of a tire andwheel assembly be moved to add more positivecamber?arrow_forwardRoad test Report is Overhaul all four-wheel brakes and the Universal joints After the maintenance operation is completed, the road test inspector or the machine creates the road test report In case of diesel engines overhaul injectors, besides the above items of wash, all the items mentioned in the monthly maintenance schedule should be carried out during quarterly maintenance also. During service, remove and clean shackle pin if necessary Skiparrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Automotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Mechanical Design (Machine Design) Clutches, Brakes and Flywheels Intro (S20 ME470 Class 15); Author: Professor Ted Diehl;https://www.youtube.com/watch?v=eMvbePrsT34;License: Standard Youtube License