Electric Motor Control
10th Edition
ISBN: 9781133702818
Author: Herman
Publisher: CENGAGE L
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 4, Problem 12SQ
Referring to the circuit in Figure 4–12, what circuit component controls the actions of the two CR contacts?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
Explain in detail what happened to the current and voltage measurements as S1 and S2 (2nd pic (revrse polarized 9v set up)) were switched places.
When the triac is in the OFF state:
Output module
terminal strip
Triac
switch
LED output
L1
status indicator
Fuse
Optical
isolator,
Field wiring
Digital
logic
circuit
Load
L2
Internal module circuit
Simplified diagram for a single output of a discrete AC output module.
O the rated nominal current flows through the lamp
O the rated surge current flows through the lamp
O zero current always flows through the load
small leakage current may flow through the load
a
What happened if the DC voltage in the clamping circuit is replaced by an a.c source?
Chapter 4 Solutions
Electric Motor Control
Ch. 4 - Identify the following symbols.Ch. 4 - Electrical symbols usually conform to which...Ch. 4 - What do the following abbreviations stand for? a....Ch. 4 - Single-pole and double-pole switch symbols are...Ch. 4 - The symbol shown is a a. polarized capacitor. b....Ch. 4 - The symbol shown is a a. normally closed float...Ch. 4 - The symbol shown is a(n) a. iron core transformer....Ch. 4 - The symbol shown is a a. normally open pressure...Ch. 4 - The symbol shown is a a. double-acting push...Ch. 4 - If you were installing the circuit in Figure 412,...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.Similar questions
- How diodes and transistors are being used as switches?arrow_forwardDetermine the voltage at resistor R2. (assume Zener voltage is 4 volts and LED forward voltage is 2.0 Volts)arrow_forwardZENER DIODES: Answer letter D only. Answers are already GIVEN. I just need you to explain them in plain English. Draw additional circuits if necessary to state your point. Was that voltage divider rule?arrow_forward
- a) Figure 3 illustrates a thyristor phase control circuit and associated waveforms. Describe the function of the control element in the circuit towards the output at the load. Identify the best-suited application to describe the control circuit. Lamp Load VAC SCR r 9 8₁ Conduction MM h 18₂ h Gate Trigger Pulsearrow_forwardIf we wanted the display to light up the left seven segment LEDs instead of the right ones, what would we change? What is the significance of the "Anodes" (AN0, AN1, AN2, and AN3) ?arrow_forwardWhat is the most dangerous test that is perform with an electrical safety analyzer on a piece of medical equipment with patient leads? Why is it dangerous?arrow_forward
- 4aa) This question is about half wave rectifier Half wave rectifier with a reservoir capacitor -> connected -> AC mains supply (220Vrms, 50Hz) by 20:1 transformer. What is the value of capacitor for the ripple voltage of 12% of the peak input voltage? The load's maximum current is 170mA. Show the full working!arrow_forward12. These are semiconductor devices that are primarily used in electronics as electronically controlled switches a. Diodes b. Transistors c. Vacuum Tubes d. Thyristors 13. If an SCR is suspected of not functioning properly, it should be tested a. with power off b. with multimeter set to the diode or high resistance function c. With the SCR leads isolated d. All of the above 14. A thyristor that looks like two back-to-back 4 layer diodes is the a. SCR b. Triac c. SCS d. DIAC 15. A device that has an unstable negative resistance region is the a. UJT b. SCS c. TRIAC d. DIACarrow_forwardHow dual diode LED works?arrow_forward
- Explain and discuss how the clamper circuit workarrow_forwardhelp me in these questions pls write the questions with the and by (Computer)1- Explain how the circuit below works to perform its main function?i. Zener diode is short circuited when voltage across it rises beyond its breakdown voltage.ii. Radiation from light emitting diode is detected by a phototransistor without having any physical contact.iii. The circuit prevents the LED from having the wrong polarity or too high voltage.iv. The circuit prevents the alternating signals by rectifying it using a diode. a. All the answers. b. i, ii and iii only. c. i, iii and iv only. d. i, ii and iv only.========2- Which of the following statement is most probably INCORRECT in explaining the working principle of an engine management system? a. Microprocessor is used to process incoming signal including position, speed, timing, flow, and temperature. b. The operation of valves and spark ignition is in sequence following the stroke action. c. The timing of the sequence is fixed.…arrow_forwardIdentify the troubleshooting procedures to determine the serviceability state of the circuitsarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Introduction to Logic Gates; Author: Computer Science;https://www.youtube.com/watch?v=fw-N9P38mi4;License: Standard youtube license