Structural Analysis
6th Edition
ISBN: 9781337630931
Author: KASSIMALI, Aslam.
Publisher: Cengage,
expand_more
expand_more
format_list_bulleted
Question
Chapter 2, Problem 5P
To determine
Find the dead loads acting on the girder AE and beam CD.
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
The floor system of a gymnasium consists of a 130- mm-thick concrete slab resting on four steel beams (A = 9,100 mm2) that, in turn, are supported by two steel girders (A = 25,600 mm2), as shown in Fig. P2.7. Determine the dead loads acting on beam BF and girder AD.
The floor of an apartment building, shown in Fig. P2.3, is subjected to a uniformly distributed load of 45 psf over its surface area. Determine the loads acting on the floor beams AF, BG, and CH and the girders AC and FH of the framing system.
PROBLEMS
1002. A timber beam is reinforced with steel plates rigidly
attached at the top and bottom as shown in Fig. P-1002. By what
amount is the moment increased by the reinforcement if n = 15 and the
allowable stresses in the wood and steel are 8 MPa and 120 MPa,
respectively?
Ans. 52.2 kN-m
150
ma
w
10 mm
150
mm
250 mm
300 mm
10 mm
Knowledge Booster
Similar questions
- The roof of a single-story storage building, shown in Fig. P2.1, is subjected to a uniformly distributed load of 0.96 kPa over its surface area. Determine the loads acting on the floor beam BE and the girder AC of the framing system.arrow_forwardA doubly symmetrical I-section beam is reinforced by a flat plate attached to the upper flange as shown in Fig. P.10.3. If the resulting compound beam is subjected to a vertical shear load of 200 kN, determine the distribution of shear stress in the portion of the cross section that extends from the top of the plate to the ncutral axis. Calculate also the shcar force per unit length of bcam resisted by the shear connection between the plate and the flange of the I-section beam.arrow_forwardA box beam, built up as shown in Fig.. , is secured by screws spaced 5 in. apart. The beam supports a concentrated load P at the third point of a simply supported span 12 ft long. Determine the maximum value of P that will not exceed fy = 120 psi in the beam or a shearing force of 300 lb in the screws. What is the maximum flexural stress in the beam? 8 in 6 in 8 in 10 inarrow_forward
- A cast iron beam is of T-section as shown in Fig. 7.21. The beam is şimply supported on a span of 8 m. The beam carries a uniformly distributed load of 1.5 kN/m length on the entire span. Determine the maximum tensile and maximum compressive stresses. 100 mm 20 mm 32.23 Fmm 80 mm 100 mm 67.77 mm 20 mm- Fig. 7.21arrow_forwardThe wall of a building is composed of braced W360 x 57 steel columns connected rigidly to a concrete foundation as shown above. Each column has a height of 4 m. The steel has a Young’s modulus of ? = 200 GPa and yield strength ?? = 500 MPa.a) For buckling about its strong axis (x-x), what are the support conditions at each end and what is the effective length?b) For buckling about its weak axis (y-y), what are the support conditions at each end what is the effective length?c) What is the critical load P able to be sustained by the column shown above?arrow_forwardGiven. A two-story OCBF shown in Fig. 3.40c that forms part of the building frame system in SDC E. The axial loads on the ground floor brace B1 are as follows: Dead load D= 30 kips Live load L= 15 kips Seismic force QE = ±80 kips Snow load S= 0 kips Hydrostatic load H = 0 The redundancy coefficient p = 1.1. Mapped two-second såpectral acceleration, Sps = 0.826 g. Required. Determine a pipe section for brace B1, ASTM A53 Grade B steel; F, = 35 ksi, F = 60 ksi 16 ft 16 ft Figure -15 ft B2 B1 -- -15 ft B2 B1 Ordinary concentric brace frame (OCBF) example.arrow_forward
- A floor opening in a building is to be closed by pouring a concrete slab. The proposed framing is composed ofwood joist assumed to be simply supported and given with a total load of 4 kPa. What is the maximum flexural stress in 40 mm x 190 mm wood joist if its span is 3 m and spaced atevery 0.30 m on centers?a. 5.61 MPa c. 6.78 MPab. 7.23 MPa d. 4.65 MPa What is the maximum shearing stress in the said joists?a. 0.40 MPa c. 0.36 MPab. 0.69 MPa d. 0.54 MPaarrow_forwardA channel-shaped beam with an overhanging end is loaded as shown in Fig. 7-46. The material is gray cast iron having an allowable working stress of 30 MPa in tension and 120 MPa in compression. Determine the maximum allowable value of P. Also compute the shearing stress developed in the beam loaded with P computed. P 2 cт 20 ст 2P cm 2 cm 12 cm 2 m 2 m- 1 m Fig. 7-46arrow_forward2. A beam with an inverted U section is loaded as shown. What is the max flexural stress developed and the max beam shear developed in the beam? 30mm 30mm 2m 6m 2m 200m 250mm 40mmarrow_forward
- EXAMPLE 6-16 The beam shown in Fig. 6-29a has a cross-sectional area in the shape of a channel, Fig. 6-29b. Determine the maximum bending stress that occurs in the beam at section a-a. 2.6 kN 13/12 2 m (a) 1 m. y=59.09 mm N 15 mm- -250 mm- C 20 mm AT 200 mm -15 mmarrow_forwardiss 40 mm 200 m 40 mm FIG. P5.100 5.100 The bending moment acting on the cross section of the beam is M = 1.8 kN m. Find the maximum tensile and compressive bending stresses acting on the cross section.arrow_forwardProblem 5.7. Box beam with strain gauges A cantilevered beam of length L is subjected to axial and transverse loads. Figure 5.34 depicts the cross-section of the beam: an aluminum rectangular box of height h = 0.30 m, width b = 0.15 m, flange thickness ta %3D = 12 mm, and web thickness t, = 5 mm. The beam is reinforced by two layers of unidirectional composite material of thickness te = 4 mm. The Young's moduli for the aluminum and unidirectional composite are Ea = 73 GPa and Ec = 140 GPa, respectively. At a station along the span of the beam, an experimentalist has measured the axial strains on the top and bottom flanges of the beam as Etop = -20a e %3D -2560u and 3675µ, respectively. Find the bending moment and axial force acting at that siation. %3D Ebot =arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you