Concept explainers
Interpretation:
Given table has to be completed using the number of significant figures, estimated digit and magnitude of uncertainty for the given number in the first column.
Concept Introduction:
Whenever a measurement is made, the significant figures in the measured quantity give the actual measurement. For this the significant figures should be recognized first. The significant figures may be non-zero digit and zero digit. But Zero may be or may not be a significant figure. It depends on where the zero appears. Leading zeros in the front of any number are never significant. Zeros between the numbers are significant. When an object is measured with a scale having graduations in centimeter, and if the length of the object falls between 5 and 6, the estimated length would be 5.2 cm. But this value is approximate. This is called the uncertainty error. If the same scale is graduated in tenths of a centimeter, the measurement made would be with less degree of uncertainty. Hence if the markings become smaller, lesser is the degree of uncertainty. Also when any measurement is made, the last number that indicates the actual measurement is termed as estimated digit due to its less uncertainty. The magnitude of measurement and uncertainty of measurement are the two most important information to be conveyed in order to show case the values more exact. The significant figures any measurements are said to convey the uncertainty, while the digit values convey the magnitude.
Want to see the full answer?
Check out a sample textbook solutionChapter 2 Solutions
General, Organic, and Biological Chemistry
- Write the ordinary form of the following numbers: a 2.32 x 10-2, b 9.27 x 104 c 8.96 x 10-4arrow_forwardComplete the following table by filling in the blanks in each row with numerical values that are consistent with the number given in the first column. The first row is completed as an example.arrow_forwardIn the accompanying photo, you see a crystal of the mineral calcite surrounded by piles of calcium and carbon, two of the elements that combine to make the mineral. (The other element combined in calcite is oxygen.) Based on the photo, describe some of the physical properties of the elements and the mineral. Are any properties the same? Are any properties different? Calcite (the transparent, cube-like crystal) and two of its constituent elements, calcium (chips) and carbon (black grains). The calcium chips are covered with a thin film of calcium oxide.arrow_forward
- What is the difference between an exact number and an inexact number? Give an example of each type of number.arrow_forwardWrite the following metals using Roman numeral notation. Then, explain why the Roman numeral differs for these metals. . . Co²+ Fe₂O3 Answer in complete sentences. H Normal Enter your answer here √x C 2 Ix BIUS X 300 worarrow_forward10. Classify the substance shown in the sketch below. Be sure you check all the boxes under the classification column that are correct for this substance. Substance 0 gas liquid solid Classification element compound mixture pure substance homogeneous mixture heterogeneous mixturearrow_forward
- You've just solved a problem and the answer is the mass of an electron, me=9.11×10−31kilogramsme=9.11×10−31kilograms. How would you enter this number into the answer box? Enter your answer in kilograms using three significant figures. Note that the units are provided for you to the right of the answer box. View Available Hint(s)arrow_forwardV Complete each row of the table below by filling in the missing prefix or missing exponent. 1 kN 1 N 1 N 1 m N = 10 = 10 10 = 10 0 -9 -6 0 N N N N 3 X Garrow_forwardIf a sample of gold alloy has a mass of 87.7 g and is 78.3% gold by mass, what percentage of the alloy is made up of other metals? Write your answer to the nearest tenth of a percent. (I had to alter the wording of this question since it wasn't calculating significant figures properly, so if you got it wrong because of significant figures you can assume you probably actually got it correct.)arrow_forward
- Super fine 40-gauge copper wire has a diameter of only 0.080 mm and weighs only 44.5 g/km, Suppose a spool of 40-gauge wire weighs 259. g less after some wire is pulled off to wind a magnet. How could you calculate how much wire was used? Set the math up. But don't do any of it. Just leave your answer as a math expression. Also, be sure your answer includes all the correct unit symbols. length of wire = 0 ロ・ロ X 믐 4arrow_forwardChemistry Describe the difference between accuracy and precision. How do we determine accuracy and precision? What type of graph would be best for representing the following types of data? The magnitude of two or more discrete, or separate, categories of a variable. A measurable characteristic of a sample which depends on the concentration of the sample. How would you indicate variability or dispersion in a data set on a grapharrow_forwardA brick has a mass of 4.0 kg and the Earth has a mass of 6.0 × 10- g. Use this information to answer the questions below. Be sure your answers have the correct number of significant digits. What is the mass of 1 mole of bricks? How many moles of bricks have a mass equal to the mass of the Earth?arrow_forward
- General, Organic, and Biological ChemistryChemistryISBN:9781285853918Author:H. Stephen StokerPublisher:Cengage LearningIntroductory Chemistry: An Active Learning Approa...ChemistryISBN:9781305079250Author:Mark S. Cracolice, Ed PetersPublisher:Cengage LearningChemistry: The Molecular ScienceChemistryISBN:9781285199047Author:John W. Moore, Conrad L. StanitskiPublisher:Cengage Learning
- Introductory Chemistry: A FoundationChemistryISBN:9781337399425Author:Steven S. Zumdahl, Donald J. DeCostePublisher:Cengage Learning