Which of the following are the assumptions in designing boiler joints? I. Crushing stress varies parabolically II. There is no bending stress in rivets III. The shearing stress in all rivets is uniform IV. The tensile stress is equally distributed over the section of metal between the rivets Choose the correct option from the options given below. : A. OI and III only B. O1, II and III only C. OII, III and IV only D. O All I, II, III and IV

Which of the following are the assumptions in designing boiler joints? I. Crushing stress varies parabolically II. There is no bending stress in rivets III. The shearing stress in all rivets is uniform IV. The tensile stress is equally distributed over the section of metal between the rivets Choose the correct option from the options given below. : A. OI and III only B. O1, II and III only C. OII, III and IV only D. O All I, II, III and IV

Name: i need correct explanation my best wishes ton Q 17. Which of the follo
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: i need correct explanation my best wishes ton Q 17. Which of the following are the assumptions in designing boiler joints?I. Crushing stress varies parabolicallyII. There is no bending stress in rivetsIII. The shearing stress in all rivets is uniform

Automotive Technology: A Systems Approach (MindTap Course List)

6th Edition

ISBN:9781133612315

Author:Jack Erjavec, Rob Thompson

Publisher:Jack Erjavec, Rob Thompson

Chapter40: Drive Axles And Differentials

Section: Chapter Questions

Problem 8RQ: The double-offset joint is typically used in applica tions that require______. a. higher operating...

See similar textbooks

Similar questions

1. A collar is fitted as a tight fit on a solid shaft. In the measurement made before assembly, the outer diameter of the ring is dga=159.97 mm, the inner diameter is dgi= 100.03 mm, and the outer diameter of the shaft is dma= 100.048 mm. After assembly; a. What is the surface pressure between the shaft and the ring? b. What is the maximum shear stress? Given: Material pair steel/steel P E=2.1x10$ N/mm?, Tmax (1-Q¿)
Please answer with explanation. Question : These two shear pins have the same length and same cross-sectional area. Both are subject to the same external tension load. Which pin has the lower shear stress? O a. The solid pin on the left. O b. The hollow pin on the right. O c. Both pins have the same shear stress.
TRUE OR FALSE ? QUESTION : For a bolt pattern in shear, if the line-of-action of the load passes through the centroid of the bolt pattern, then the secondary shear force, Fi'', will be zero.
HOW TO SOLVE: Draw the FBD of one member Solve for the bearing force. Section one bold and solve internal forces. Solve for the normal and shear stress in the bolts. Solve for the bearing stress in the members due to the nuts. Solve for the bearing stress in the members due to bolts. ANSWERS: bearing stress of bolt= 7.96 MPa, T; shear stress of bolt= 13.78 MPa; bearing stress (max)= 18.04 MPa
Problem 2 For each of the structures shown in Fig.2, sketch the following: Free body diagrams showing the magnitudes of all applied loads, reaction forces/moments, and parts dimensions) Shear force and bending moment diagrams. Please indicate the critical location for failure of part. i. ii. {Hint: In some cases, you may have to draw FBD and BM diagrams in two different orthogonal planes} 196 ag 1.25-in dia. Gear A 20-in dia. 300 lbf 16 in 20⁰ A 14 in 100 Gear B 8-in dia. 9 in B 750 lb 20° b)
Sketch a V-grooved butt joint, and label all of the joint's dimensions.
The double-offset joint is typically used in applica tions that require______. a. higher operating angles and greater plunge depth b. lower operating angles and lower plunge depth c. higher operating angles and lower plunge depth d. lower operating angles and greater plunge depth
H.W: Design a knuckle joint for a tie rod of a circular section to sustain a maximum pull of 70 kN. The ultimate strength of the material of the rod against tearing is 420 MPa. The ultimate tensile and shearing strength of the pin material are 510 MPa and 396 MPa respectively. Determine the tie rod section and pin section. Take factor of safety = 6.
Q2/ Calculate the maximum axial stress for a 40-ft joint of 11.75-in, 60 lbm/ft, J-55 casing with short threads coupling. Where the casing is subjected to 280000 lb, axial tension load in a portion of a directional wellbore with dogleg severity of 2"/50 ft. In case of: (1)Uniform contant between the casing and the borehole wall. (2)Assuming contant between borehole wall and the casing only at the couplings,andF n+ (3)Calculate the joint setrength of the API round thread couplings.(oult = 75000 psi, wall thickness 0.489-in, Pc= 2660 psi. o yb-952000 lb, Fj-649 000 lbf).
4. A solid shaft was made of alloy steel, it was welded to a flat plate by a specific size of fillet weld. If a torque is applied to the shaft, calculate the size of the weld joint. Power Torque Yield stress Shear stress Ultimate stress (Mpa) Compression stress (Mpa) Ductility (%) (kw) (Nm) 1000 (Mpa) 400 (Mpa) 160 280 30 Modulus of Bending Stress Bending Moment Factor of Safety Elasticity (GPa) (Mpa) 220 280 120 4 Modulus of Rigidity (pa) 70 Fracture stress (Mpa) 250
Find the size of 14 bolts required for C.I.steam engine cylinder head. The diameter of the cylinder is 400 mm and the steam pressure is 0.12 N/mm.
A 945 lb Q3) Analysis the truss by method of joint? 9ft 12 ft 3.75 ft اضف ملف ك