4. A solid shaft was made of alloy steel, it was welded to a flat plate by aspecific size of fillet weld. If a torque is applied to the shaft, calculate the size ofthe weld joint.PowerTorqueYield stress Shear stressUltimatestress (Mpa)Compressionstress (Mpa)Ductility (%)(kw)(Nm)1000(Mpa)400(Mpa)16028030Modulus ofBending Stress Bending MomentFactor of SafetyElasticity(GPa)(Mpa)2202801204Modulus ofRigidity (pa)70Fracture stress(Mpa)250

Torque (T) = 1000 Nm Shear stress (τ) = 160 MPa = 160×106 Pa

A solid shaft was made of alloy steel, it was welded to a flat plate by a specific size of fillet weld. If a torque is applied to the shaft, calculate the size of the weld joint. Power Torque Ultimate Yield stress Shear stress (Mpa) Compression stress (Mpa) Ductility (%) (kw) (Nm) stress (Mpa) (Mpa)

A solid shaft was made of alloy steel, it was welded to a flat plate by a specific size of fillet weld. If a torque is applied to the shaft, calculate the size of the weld joint. Power Torque Ultimate Yield stress Shear stress (Mpa) Compression stress (Mpa) Ductility (%) (kw) (Nm) stress (Mpa) (Mpa)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Two plates, 25 mm thick, are welded together by means of trans verse-fillet welds. The ultimate tensile strength of a weld metal is 415 MPa. The surface finish factor of the weld surface is 0.5, and the size factor is 0.85. The reliability is 90%. Determine the length of the weld if the factor of safety is 2. The transverse force on the welds is 100 kN, which is completely reversed under fatigue loading. Take: A=10mm 25 Toe Р.
Use the provided data wherever you need. Q3. A solid shaft was made of alloy steel, it was welded to a flat plate by a specific size of fillet weld. If a torque is applied to the shaft, calculate the size of the weld joint. Torque Power (Kw) Ultimate stress (Mpa) Ductility (%) (Nm) Yield stress Shear stress Compression (Mpa) 400 stress (Mpa) (Mpa) 160 640 280 1000 30 Modulus of Modulus of Fracture stress Bending Stress (Mpa) (Mpa) Elasticity (GPa) Bending Moment (Nm) Factor of Safety Rigidity (Gpa) 220 250 70 280 120 4
10. Two tie bars are connected together by 0.5cm fillet welds around the end of 1 bar and the inside of a slot machined in the same bar. Estimate the strength of the connection in tension if the shearing stress in the welds is limited to 75MPa. 450m 10cm 8cm
sheet Hw Asteel bar of rec tangular crossl seetion with dimension as -s hownin fig- belo .This bar is Connected toawell. Using welded Juin along the sides only- find the weld size Ch) .where: Tall= 75 N /m? answer h= 4.04 %3D %3D F=213.3 N yomm 50omm l0omm
An AISI 1050 HR solid tube of 20mm diameter is acted by force F1 = IkN, and force F2 of 2kN. The tube is welded to a larger round base by 3mm fillet weldment, the base is connected to the ground base (shown in gray color) by means of four bolts M8x1.25mm (property class of 4.8)). The bolts are evenly distributed at 20mm away from the center of the tube. R=100 F1 120 120. F2 R=100 D =20 120 R=3 D =60 40 Dimensions are in mm Perform the following the following: 1- Find the state of stress for the most critical point on the assembly and build the mohr's circle. Solve question 1
asap
Find. The weld sizé W for the welted.join .shawai figure T=2 Nimっ below where aaill =3.MPag Tall=1.5 Mfa F=500 N ..in. D = l00 mm 2 6. =300M m %3D Ans: h=9.1 mm 4s0.707t A TO @ab ending
Problem 3.1: Determine the design strength of a 1 mm length of a 6.35 mm fillet weld formed by the shielded metal arc process (SMAW) and E70 electrodes with a minimum tensile strength Fexx = 483 MPa. Assume that the load is to be applied parallel to the weld length. Problem 3.2: Repeat problem 3.1 if the weld is 500 mm long. Problem 3.3: Repeat problem 3.1 if the weld is 750 mm long. Problem 3.4: Repeat problem 3.2 if the application of the load is at an angle of 35 degrees from the longitudinal axis of the weld. Problem 3.5: Repeat problem 3.3 if the application of the load is at an angle of 35 degrees from the longitudinal axis of the weld.
Figure 4 shows a rectangular hollow steel bar welded to a vertical member. The bar has to support a IkN load at its free end. Fillet welds extend all around the outer periphery of the bar. Assuming that the Distortion Energy Theory is applicable, i.e., Say = 0.58 x S, determine the required weld size using a welding rod with S, = 330 MPa and a safety factor of 3 based on yielding. Neglect the weight of the rectangular bar. 1 kN 60 2 25 15 Figure 4 with all dimensions given in millimetres
Azt Qet If Chao.7 cm) for weld , fincd (Iimax) for figure blow: l00 225mm of f=400W 150mm 45.27 mlam? answer: Tomax
find the tensile of the bolt with diameter 38mm,80kN
Mechanical Engineering Question