What is the threshold torsion (kN-m) of a rectangular beam with a width of 402 mm and an over-all depth of 571 mm? The distance of the tension reinforcements from the bottom fiber of the beam is 72 mm. The specified compressive strength of concrete is 25.62 MPa. The yield strength of tension reinforcements and stirrups are 387 MPa and 300 MPa respectively.

What is the threshold torsion (kN-m) of a rectangular beam with a width of 402 mm and an over-all depth of 571 mm? The distance of the tension reinforcements from the bottom fiber of the beam is 72 mm. The specified compressive strength of concrete is 25.62 MPa. The yield strength of tension reinforcements and stirrups are 387 MPa and 300 MPa respectively.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A. Calculate the stress in the concrete at the top and bottom extreme fibers under a positive bending moment of 78 kip, in psi (neglect steel reinforcement) B. If fc= 3200 psi and normal weight of concrete is used, does cracking occurs? What is the maximum uniformly distributed load the beam can carry if it is used as a simple beam with a 26 ft span without exceeding the modulus of rupture of the concrete, in lb/ft? 250 mm 80 mm 130 mm 80 mm 80 mm
If the compressive strength of the concrete is 4 ksi and the yield strength of steel is 60 ksi, the value of that should be used in computing the design moment strength oMn for the beam section should be 23.5 in 1.5424 0.65 0.48 0.9 3#9 14 in 26 in
The following data of a pre-stress concrete are given: Beam dimension ; bxh = 300 mm x 600 mm Loads Super imposed dead load 7 KN/m Live load = 20 KN/m Unit Weight of concrete 23 KN/cubic meter The beam is simply supported on a span of 15 meters and are pre tensioned with total initialpre tensioned with total initial force of 1750 KN from low-relaxation strand with centroid 220 mm below neutral axis throughout the beam length .There is a 15% loss of stress at service loads. The concrete covering of the pre-stressed concrete is _____mm., the total dead load is _____ KN/m.
2. Tensile strength of concrete is about: (20-35)% of compressive strength (45-70)% of compressive strength None of the above. Tension controlled section Balanced section Compression-controlled section 4- The reduction factor (0) is equal to 0.9 if the: Es 2 Ety + 0.003 Es S Ety + 0.003 Es Ety 5- The design method which use the factored loads is - Working stress method - Ultimate design Method - None of above 6- If p< Po therefore the section is - Under reinforced - Over reinforced - None of above
A beam having a width of 500 mm and a total depth of 800mm is reinforced with 6-32mm dia bars. Compressive strength of concrete is 28 MPa and yield strength of reinforcing bars is 420MPA. 640 mm 800 mm 6 #32 C 80 mm 80 mm Determine the following: 1. depth of the compression block 2. strain in the tension reinforcement 3. moment reduction factor 4. nominal moment capacity 5. ultimate moment capacity 6. actual steel ratio 7. minimum steel ratio 8. maximum steel ratio 9. Tension force 10. Compression force
The grade of the concrete is M25. Find the values of design strength in- 1. Direct Compression. 2. Bending Compression & 3. Flexural Tension.
21. The column of reinforced concrete is loaded with P = 8000 lbs. The modulus of elasticity (E) is 4.2E6 psi and the Poisson ratio is 0.15. 16in 16in What is the normal stress along section b-b? a. -15.625 psi b. -7.81 psi c. -2.60 psi d. -11.04 psi
Item 5 Column AB is made from high strength pre-cast concrete and reinforced with four in diameter A-36 steel rods. The allowable normal stress for the high strength concrete and the steel are (allow) con = 2.6 ksi and (allow) st = 24 ksi, respectively. The modulus of elasticity for high strength concrete is 4.2 x 10³ ksi and for A-36 steel is 29 x 10³ ksi. (Figure 1) Figure 1 ▾of 1 10 ft a P B9 in. 9 in. Section a-a Part A Determine the magnitude of the maximum allowable floor loading P. Express your answer to three significant figures and include the appropriate units. μA Pmax= 158.91 kips Submit My Answers Give Up Incorrect; Try Again; 2 attempts remaining ? Provide Feedback Continue
A beam having a width of 500 mm and a total depth of 800mm is reinforced with 6-32mm dia bars, Compressive strength of concrete is 28 MPa and yield strength of reinforcing bars is 420MP.. 640 mm 800 mm 6 #32 80 mm 80 mm Determine the following: 1. depth of the compression block 2. strain in the tension reinforcement 3. moment reduction factor 4. nominal moment capacity 5. ultimate moment capacity 6. actual steel ratio 7. minimum steel ratio 8. maximum steel ratio 9. Tension force 10. Compression force
The concrete in the core of a spiral column is sub- jected to a uniform confining stress o, of 680 psi. What will the compressive strength o be? The un- confined uniaxial compressive strength is 5000 psi.
9. If the value of the fc' of concrete is 30 MPa, and the actual stress of the concrete subjected to a force is 12 MPa, at what stage is the concrete at?
A pre stressed concrete beam has a width of 200 mm and an overall depth of 400 mm. The permissible stresses in tension and compression due to pre- stressing alone are 4 N/mm and 25 N/mm respectively. Find the required pre- stressing force in the tendon and the eccentricity of the tendon, if a straight tendon with a constant eccentricity is to be provided in the beam. No external load or self weight effect is to be considered.