The following data of a pre-stress concrete are given: Beam dimension ; bxh = 300 mm x 600 mm Loads Super imposed dead load 7 KN/m Live load = 20 KN/m Unit Weight of concrete 23 KN/cubic meter The beam is simply supported on a span of 15 meters and are pre tensioned with total initialpre tensioned with total initial force of 1750 KN from low-relaxation strand with centroid 220 mm below neutral axis throughout the beam length .There is a 15% loss of stress at service loads. The concrete covering of the pre-stressed concrete is _____mm., the total dead load is _____ KN/m.

The following data of a pre-stress concrete are given: Beam dimension ; bxh = 300 mm x 600 mm Loads Super imposed dead load 7 KN/m Live load = 20 KN/m Unit Weight of concrete 23 KN/cubic meter The beam is simply supported on a span of 15 meters and are pre tensioned with total initialpre tensioned with total initial force of 1750 KN from low-relaxation strand with centroid 220 mm below neutral axis throughout the beam length .There is a 15% loss of stress at service loads. The concrete covering of the pre-stressed concrete is _mm., the total dead load is _ KN/m.

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter12: Composite Materials

Section: Chapter Questions

Problem 12.7P: Estimate the transverse tensile strength of the concrete in Problem 12.6.

See similar textbooks

Similar questions

A pre-tensioned concrete member of section 200 mm x 250 mm contains tendons of area 500 mm2 at centre of gravity of the section. The pre-stress in the tendons is 1000 N/mm2.- Assuming modular ratio as 10, the stress (N/mm2) in concrete is
A rectangular reinforced concrete beam has a width of 350 mm and an effective depth of 650 mm. The beam is reinforced with 8-28 mm diameter tension bars. Concrete strength is f'c = 20.70 MPa and steel yield strength is fy = 275 MPa. 1. Which of the following most nearly gives the steel ratio? A. 3.73% B. 2.79% C. 2.17% D. 1.62% the rectangular
c) Find the stresses in the concrete and the reinforcement for the following applied moments: (i) – M1= 35kN.m and (ii) – 120kN.m Cross-section: width height Modulus of elasticity: concrete reinforcement Reinforcement: depth area b:= 300-mm h := 520-mm Ec:= 30-GPa Es:= 200-GPa d:= 460-mm As 1470-mm 2 h d b
The cross section of a beam is shown in the figure is reinforced with 5-28 mm diameter bars placed at 100 mm from the bottom fiber. The beam is expected to carry a service moment of 280 kN-m. Use f'c=28 MPA and fy=280 MPa. All dimensions are in millimeters. Using WSD method, calculate the following: 1. Cracking moment of the section. 2 Compressive stress on the concrete., 3. Tensile stress on the steel. 4. Compressive force on the concrete. 300 I00 300 300 300 100 mm 100 -1700 mm
A pre stressed concrete beam has a width of 200 mm and an overall depth of 400 mm. The permissible stresses in tension and compression due to pre- stressing alone are 4 N/mm and 25 N/mm respectively. Find the required pre- stressing force in the tendon and the eccentricity of the tendon, if a straight tendon with a constant eccentricity is to be provided in the beam. No external load or self weight effect is to be considered.
SIT. B: Determine the tensile steel ratio of a given conditions if concrete strength f'. = 28 MPa and steel yield strength fy 4. if the tensile strain is Es = fy/Es upon crushing of concrete at a strain of 0.003. C. 0.02833 A. 0.01567 B. 0.02161 D. 0.02125 if the tensile strain is limited to 0.004 upon crushing of concrete at a strain of 0.003. A. 0.01567 B. 0.01548 5. 6. Minimum as required by NSCP 2015. C. 0.00313 D. 0.00405 A. 0.00333 B. 0.00276 = 420 MPa. C. 0.02778 D. 0.02064 uniformly
Determine the prestressing steel area required for the precast concrete T-beam. Use the following data: Total moment = 250 kN-m Effective stress fse= 862 MPa Allowable concrete stress = f.=11 MPa Consider zero stress at the bottom of the beam I=3673x106 mm4 A=103125 mm² Eccentricity = 271.6 mm Centroid of steel is located at 100 mm from the bottom of the beam. Select one: a. 591.97 mm b. 789.29 mm 2. C. 443.98 mm 2. d. 986.61 mm
A singly reinforced rectangular section has a width of 250mm and an effective depth of 460mm. The concrete has a compressive strength of 21MPa. The steel has a yield strength of 275 MPa and E = 200,000 MPa. Calculate the ideal flexural strength for the following areas of steel: a. 2580 mm² b. 5160 mm² c. The value at balanced failure
CASE:A rectangular beam has the dimensions (see Fig.1) b = 15 in.,h = 30 in., and d = 27.37 in. and is reinforced with three No.9 bars. The concrete compressive strength fc' is 4000 psi, and the tensile strength in bending (modulus of rupture) is 475 psi. The yield point of the steel fy is 60,000 psi, the stress-strain curves of the materials being those of Fig.2. Determine the stresses caused by a bending moment M = 45 ft-kips.Question1:Check this case, would the concrete of the beam crack? Please calculate the strengths of those two materials in this beam.Question2:Suppose the beam under this case is subject to a bending moment M = 110 ft-kips (rather than45ft-kips as previously). Calculate the relevant properties and stresses.Question3:Determine the nominal moment Mn at which the beam of this case will fail. Question4:Have a comparison of the calculation results with those of three questions.
Assuming concrete is uncracked. Compute the bending stress in the extreme fiber of the beam of figure for bending moment 1x10°kg cm . Determine the cracking moment of the section. A = 10cm² %3D E, = 2*10°kg / cm² E = 2*10°kg / cm² %3D %3D f'. =1836kg / cm² %3D 90 cm 100 cm 40 cm
A rectangular reinforced concrete beam has a width of 300mm and an effective depth of 400mm. Concrete strength is f'c = 28 mpa and steel yield strength is fy = 280 mpa. The modulus of elasticity of steel is 200,000 MPa Compute for the total compressive forceon concrete.
Determine the tensile steel ratio of a singly reinforced concrete beam for the following conditions using concrete strength f’c = 28 MPa and steel yield strength fy = 420 MPa. if the tensile strain is εs = fy/Es upon crushing of concrete at a strain of 0.003. = ___ (5 decimal places)