What is the gain in the circuit shown? The Voltage V1, is 6.75 volts, Resistor R1 is 2.0 k-ohms, Resistor R2 is 11.4 k- Your answer should be recorded to two decimal places. ohms. U1 Rout V1 741 R2 R1 You want approximately 2.7. You only have 2.2k, 5.6k, 12k, 15k, and 33k). What resistor value will you to create an inverting OpAmp circuit with a gain of The diagram of the OpAmp is shown below. (1k, the following resistors to choose from choose for R1 and R2? U2 Rout R1 741 R2 V1

What is the gain in the circuit shown? The Voltage V1, is 6.75 volts, Resistor R1 is 2.0 k-ohms, Resistor R2 is 11.4 k- Your answer should be recorded to two decimal places. ohms. U1 Rout V1 741 R2 R1 You want approximately 2.7. You only have 2.2k, 5.6k, 12k, 15k, and 33k). What resistor value will you to create an inverting OpAmp circuit with a gain of The diagram of the OpAmp is shown below. (1k, the following resistors to choose from choose for R1 and R2? U2 Rout R1 741 R2 V1

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter7: Parallel Circuits

Section: Chapter Questions

Problem 3PP: Using the rules for parallel circuits and Ohmslaw, solve for the missing values....

See similar textbooks

Similar questions

Using the rules for parallel circuits and Ohmslaw, solve for the missing values. ETE1E2E3E4ITl1I2l33.2AI4RT3.582R116R210R3R420PTP1P2P3P4
Calculate the output for the given circuit . R2 R2 Voo R R R1 ww Let the values are R1=257.6ohm,R2=828.97 ohm .The error voltage is =8.9 Volt and the initial value of output is 2 Volt. Vout = volt.
Calculate the output for the given circuit. R2 R2 ww Voa Veo R1 Let the values are R1=381.7ohm,R2=890.36 ohm .The error voltage is =5 Volt and the initial value of output is 3.4 Volt. Vout = volt.
Question 11 Not yet answered Marked out of 1.50 P Rlag question 11. Consider a PV Module with 4 solar PV cells with the Size of each 10cm x 10cm are connected in Parallel. Choose the correct statement for the above PV Module. (Assume necessary data) a. The output voltage is 2 V, the output power is 12W b.The output voltage is 0.5 V the output poweris 1W EThe outout voltageis 12V, the output power is CW 4:Theoutbutvotages.0 he outpu Question 12 Harqueseion
Q1- According to the following figure answer the questions:- R. 22 Ce FM Demoduduted put Cs 0.05 100 001 LMHE 1- What is the function of U1& U2. 2- What is the function of D1. 3- What is the function of( R5,C4,C5). 4- What is the function of (C6). 5- What is the name of this circuit.
In the circuit given below, calculate the drain current (lo) of the 2N7002 when R1 = 286 0 and R2 = 6,2 k2. V1 D2 R3 12V 4.7K M1 U1 2N7002 LM350 R2 R1 tran 1m O a. 38,19 mA O b. 16,71 mA O .9,55 mA O d. 59,67 mA O e. 45,35 mA O f. 31,03 mA O g. 52,51 mA O h. 23,87 mA
If R1 is on, the collector current in the figure is Please select one: a. 0 mA b. 10 mA c. 5.17 mA d. 4.83 mA
Consider a PV Module with 8 PV cells with the Size of each 10cm x 5cm are connected in series. Calculate the following for the above Module. Refer to the above PV Module choose the correct statement a. The output power of each PV cell is 0.5 W b. The output power of each PV cell is 0.75W c. The output power of each PV cell is 1W d. The output power of each PV cell is 0.25W
V1= 1.5Vkn=0.25mA/V2Find Q-point
In step 2 you measured the voltage across each of the LEDs. This is their “forward voltage” that is referred to in the LED component page, which is the voltage required to light the LEDs. Notice that the combined forward voltage of D1 and D2 is greater than 3.3V, the LEDs will not light up at all. You should also have noticed that the forward voltage for one of the LEDS is lower than the forward voltage for the other LED. Some LEDS require less energy to light than others. Since D1 and D2 are in series, the same current will flow through each, but the different voltages across each LED reflect the different energy requirements. Finish each statement below, bears on this information and in the measurements you took in step 2 The measured forward voltage across D1 in this step is ________ The measured forward voltage across D2 in this step is ________
Reduction is the _______ of electrons. * gain t ransfer sharing loss
Evaluate the circuits (a and b) below and determine the voltage of VS1 for both circuits.