With the negative probe connected to ground, measure and record the following voltages, in reference to ground: • High potential side of D1 - This will give you the voltage across the entire series. Expected value is about 5V. · Between D1 and R1 (you can use the low side of D1 or the high side of R1, since the readings will be the same). Expected value is about 3.3V because the forward voltage of D1 is about 1.7V, leaving 3.3V for the rest of the components in the series. • Between R1 and D2. This will give you the forward voltage of D2 in this series. Expected value is about 2.8V. ince you know the voltage in reference to ground at each point in the series, you can also easily determine the voltage across any individual component. The ground eferenced voltage on the high side of the component, minus the voltage on the low side of that component, will tell you the voltage across the component. You can onfirm the answer by measuring the voltage directly across the component, which should be very close to the same value. The meter rounds values up or down a ttle, so the numbers may not always match exactly, but they should be very close. You will need the voltage across R1 (with D1 and D2 both lit) for the assignment. WARNING: If, at any point in this assignment, the voltage across R1 is zero while the circuit is turned on, this means the resistor has been shorted and you risk burning out D1 or damaging D2. Make sure R1 is not shorted.

Introductory Circuit Analysis (13th Edition)
13th Edition
ISBN:9780133923605
Author:Robert L. Boylestad
Publisher:Robert L. Boylestad
Chapter1: Introduction
Section: Chapter Questions
Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...
icon
Related questions
icon
Concept explainers
Question
In step 2 you measured the voltage across each of the LEDs. This is their “forward voltage” that is referred to in the LED component page, which is the voltage required to light the LEDs. Notice that the combined forward voltage of D1 and D2 is greater than 3.3V, the LEDs will not light up at all. You should also have noticed that the forward voltage for one of the LEDS is lower than the forward voltage for the other LED. Some LEDS require less energy to light than others. Since D1 and D2 are in series, the same current will flow through each, but the different voltages across each LED reflect the different energy requirements. Finish each statement below, bears on this information and in the measurements you took in step 2 The measured forward voltage across D1 in this step is ________ The measured forward voltage across D2 in this step is ________
STEP 2
With the negative probe connected to ground, measure and record the following voltages, in reference to ground:
• High potential side of D1 - This will give you the voltage across the entire series. Expected value is about 5V.
• Between D1 and R1 (you can use the low side of D1 or the high side of R1, since the readings will be the same). Expected value is about 3.3V because the forward
voltage of D1 is about 1.7V, leaving 3.3V for the rest of the components in the series.
• Between R1 and D2. This will give you the forward voltage of D2 in this series. Expected value is about 2.8V.
Since you know the voltage in reference to ground at each point in the series, you can also easily determine the voltage across any individual component. The ground
referenced voltage on the high side of the component, minus the voltage on the low side of that component, will tell you the voltage across the component. You can
confirm the answer by measuring the voltage directly across the component, which should be very close to the same value. The meter rounds values up or down a
little, so the numbers may not always match exactly, but they should be very close.
• You will need the voltage across R1 (with D1 and D2 both lit) for the assignment.
WARNING: If, at any point in this assignment, the voltage across R1 is zero while the circuit is turned on, this means the resistor has been
shorted and you risk burning out D1 or damaging D2. Make sure R1 is not shorted.
Transcribed Image Text:STEP 2 With the negative probe connected to ground, measure and record the following voltages, in reference to ground: • High potential side of D1 - This will give you the voltage across the entire series. Expected value is about 5V. • Between D1 and R1 (you can use the low side of D1 or the high side of R1, since the readings will be the same). Expected value is about 3.3V because the forward voltage of D1 is about 1.7V, leaving 3.3V for the rest of the components in the series. • Between R1 and D2. This will give you the forward voltage of D2 in this series. Expected value is about 2.8V. Since you know the voltage in reference to ground at each point in the series, you can also easily determine the voltage across any individual component. The ground referenced voltage on the high side of the component, minus the voltage on the low side of that component, will tell you the voltage across the component. You can confirm the answer by measuring the voltage directly across the component, which should be very close to the same value. The meter rounds values up or down a little, so the numbers may not always match exactly, but they should be very close. • You will need the voltage across R1 (with D1 and D2 both lit) for the assignment. WARNING: If, at any point in this assignment, the voltage across R1 is zero while the circuit is turned on, this means the resistor has been shorted and you risk burning out D1 or damaging D2. Make sure R1 is not shorted.
D1
R1
D2
Red
330 Q
Blue
PSB
5 V
本
本
Transcribed Image Text:D1 R1 D2 Red 330 Q Blue PSB 5 V 本 本
Expert Solution
trending now

Trending now

This is a popular solution!

steps

Step by step

Solved in 2 steps with 4 images

Blurred answer
Follow-up Questions
Read through expert solutions to related follow-up questions below.
Follow-up Question

How much current is flowing through the circuit?

Solution
Bartleby Expert
SEE SOLUTION
Follow-up Question

What is the voltage across R1 in this step?

Solution
Bartleby Expert
SEE SOLUTION
Knowledge Booster
Protection System in Power Plant
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.
Similar questions
  • SEE MORE QUESTIONS
Recommended textbooks for you
Introductory Circuit Analysis (13th Edition)
Introductory Circuit Analysis (13th Edition)
Electrical Engineering
ISBN:
9780133923605
Author:
Robert L. Boylestad
Publisher:
PEARSON
Delmar's Standard Textbook Of Electricity
Delmar's Standard Textbook Of Electricity
Electrical Engineering
ISBN:
9781337900348
Author:
Stephen L. Herman
Publisher:
Cengage Learning
Programmable Logic Controllers
Programmable Logic Controllers
Electrical Engineering
ISBN:
9780073373843
Author:
Frank D. Petruzella
Publisher:
McGraw-Hill Education
Fundamentals of Electric Circuits
Fundamentals of Electric Circuits
Electrical Engineering
ISBN:
9780078028229
Author:
Charles K Alexander, Matthew Sadiku
Publisher:
McGraw-Hill Education
Electric Circuits. (11th Edition)
Electric Circuits. (11th Edition)
Electrical Engineering
ISBN:
9780134746968
Author:
James W. Nilsson, Susan Riedel
Publisher:
PEARSON
Engineering Electromagnetics
Engineering Electromagnetics
Electrical Engineering
ISBN:
9780078028151
Author:
Hayt, William H. (william Hart), Jr, BUCK, John A.
Publisher:
Mcgraw-hill Education,