What does a binary digital signal consist of?
Q: . Determine the truth table of the digital circuit shown in the figure below explain its operation.…
A:
Q: What is the minimum logic swing V required foran ECL gate to have a noise margin of 0.1V at…
A: The noise margin can be expressed as
Q: Use three MSI circuits,construct a binary parallel adder to add 12 bit binary numbers.
A: Addition of two one-bit numbers and an input carry can be carried out by single full adder The…
Q: What is the gate delay for 8 bit ripple carry adder?
A:
Q: What are the five differences between microcontrollers and microprocessors?
A: Microprocessor is a basic element of the computer system. Microcontroller is a basic element of the…
Q: B) Design an Octal-to-Binary (8-to-3) Encoder, and then draw a block diagram for Octal-to- Binary…
A:
Q: Is it possible to convert 16-bit binary data to 8-bit binary data such as: 1111111011111110 -> this…
A: The Solution for the given is, 16 bit number is, 111111101111111016
Q: Implement Four-to-one-line multiplexer with Logic diagram and Function table.
A:
Q: How does Arduino microcontroller differentiate an input logic signal 0 to logic signal 1 given a 5V…
A: Microcontroller is a pin device which contains Input/output ports and CPU for processing.
Q: A DDS synthesizer has a 150-MHz clock and a constant value of 15. The ROM address register has 14…
A: It is given frequency of clock that is reference frequency is, Constant is given M = 15 Length in…
Q: Discuss transistor logic in your own words
A:
Q: 1. What is the difference between synchronous binary counter and asynchronous binary counter?
A: Note:Dear student here you have posted multiple question in sigle request.We will solve first…
Q: Sketch the RS-232 waveform that results from transmitting the binary value 10100011 over a…
A: Logic Waveform RS-232 the shown waveform pertains to the RS-232 port's Broadcast and Receipt lines.…
Q: What is the difference between synchror binary counter and asynchronous binary counter?
A: Counters can be classified into two typed based on how clock signal is applied.
Q: Perform the functions given below with the decoder given below and a suitable logic gate. ?1(?,?,…
A: Here the all the output nodes are active low hence we must convert the given minterms into the…
Q: If an 8-bit binary number is used to represent an analog value in the range from 010 to 10010, What…
A: Given 010101102 is the given binary number.
Q: . If a 6-bit binary number is used to represent an analog value in the range from -63 to 126, what…
A: According to given question, analog value range 63 to 126 6 bit binary number is used to represent…
Q: What is the advantage of CMOS logic compared to TTL logic
A: We can explain the advantages of CMOS logic in terms of power, temperature ,stability etc shown…
Q: How do you differentiate digital modulation from analog modulation?
A: A message signal is transferred from the sender to the receiver end. The signal is transmitted…
Q: In a PCM system, 8 bit uniform quantiser is used. How many quantizing levels will be present if the…
A: Given: In PCM system uniform quantizer is used having number of bits, n=8
Q: 41. F
A: Given Logic Circuit, f(A, B, C) = ?
Q: 2-bit by 2-bit binary multiplier using ROM VHDL code
A: A multiplier is an electrical circuit that multiplies two binary integers in digital electronics,…
Q: Construct digital circuit for Boolean expression Q=A’B+C using only NAND gates.
A:
Q: Draw the implementation of decoding of binary state 5, and binary state 3 for a 3- bit synchronous…
A:
Q: what is the advantages of memory segment.
A: We are authorized to answer one question at a time since you have not mentioned which question you…
Q: 1a. If an 8-bit binary number is used to represent an analog value in the range from 010 to 10010,…
A:
Q: 8085 microprocessor, the ISR for handling trap interrupt is at which location?
A: In this question we will write about the ISR for handling trap interrupt is at which location in…
Q: 3 Describe the difference betueen assemblens, interpreters, aud Compilers
A: The explanation for the differences are as follows.
Q: The initial state of the four-bit synchronous binary addition counter Q3Q2Q1Q0 is 1100. After 8 CP…
A: Solution . After 8 CP clock pulses, its state Q3Q2Q1Q0 changes to 0101
Q: VHDL Difference between function and task. What is logic data type.
A: Bit is 2 state data type. It can take 0 and 1 only. Reg is driven by always block it can't be…
Q: 1- Explain the meaning and operation of CMC instruction ?
A: Since, You ask Multiple questions but we are only allowed to answer one question at a time . so…
Q: true or false ?? an even two bit parity checker will output a parity error if data A=LOW data ,…
A: Given, An even two bit parity checker will output a parity error if data A=LOW, data B=HIGH, parity…
Q: (b) Given the function Z (A+B(C+D+ E)+FG.Using static combinational CMOS logic circuit technique,…
A:
Q: below is the accuracy table showing the output values for two separate binary number entries (W and…
A: The truth table of a digital system is given as Here, W and Y are 2 bit numbers and A, B and C are…
Q: (b) Given the function Z = ((A+B (C + D+E)+FG.Using static combinational CMOS logic circuit…
A: The function is given below, Z=A¯+B¯C+D+E+FG¯
Q: a computers, integers are sometimes represented by 16 bits. What is the lar; ve base 10 integer that…
A:
Q: From the binary number 2's Complement (10011001), write it as a decimal number. andj specify the +…
A: The solution can be achieved as follows.
Q: Construct a bus system using tri state buffer for 2 registers having 4 bits each.
A: We have given the following problem Construct a bus system using tri state buffer for 2 registers…
Q: Design a BCD to 7-segment converter by using logic gates?
A: We need to design a BCD to 7 segment converter by using logic gates.
Q: what do you mean by term parity of a digital world ?
A: In digital world, parity is a technique that checks whether the data is lost or written over when it…
Q: Write an assembly language program for 8085 microprocessor to add 2 digit BCD numbers stored in…
A: to perform the given problem Registers A, C, H, L are used for general purpose several 8085…
Q: or the multiplexer circuit shown in Figure below. is performed by these multiplexers?
A:
Q: (b) Draw a block diagram of 3 bit synchronous binary counter.
A: 3-bit binary synchronous counter design :
- What does a binary digital signal consist of?
Step by step
Solved in 2 steps with 2 images
- Which statement describe a digital signal? a. is a smoothly and continuously varying voltage or current. b. will take on finite set of voltage levels. c. take on all possible values of amplitude. d. can have an infinite number of values in a range6. Which of the following is not a type of signal is... a. analog signalb. Chain signalc. Binary signald. Dict signale. digital signalplease show work included 4. If a 6-bit binary number is used to represent an analog value in the range from -63 to 126, what is the accuracy of the system? In other words, if the binary number is incremented by one, how much change does it represent in the analog value?
- An analog voltage (0 to 5) volt is to be converted to 8 bit digital form. d. What is the error made in quantization of 2.2 volt as a percentage of the input.Which statement is not true for a source encoder? a.reduces the size of the data b.Converts analog information to discrete signal c.Removes redundancy d.Converts digital input to pulsating signalAn analog voltage (0 to 5) volt is to be converted to 8 bit digital form. a. What is the resolution in volt. b. What is the digital representation of 2.2 volt. c. What is the largest quantization error as a percentage to full scale. d. What is the error made in quantization of 2.2 volt as a percentage of the input.
- Conversion of digital signal to analog signal is a. Modulation b. Demodulation c. Encapsulation d. Bypassb) Briefly describe the function of an encoder. You may use a 4 to 2 decoder to explain the functionality. What are some situations in which an encoder is used in a digital circuit?Make a signal flow diagram out of the data. Label everything properly.
- How is the analog signal converted to a digital signal? Explain this in a correct sequence, indicating the role of each stage.Q2/ The information in an analog signal voltage waveform is to be transmitted over a PCM system with an accuracy of ±0.1% (full scale). The analog voltage waveform has a bandwidth of 100 Hz and an amplitude range of -10 to +10 volts. Find the minimum sampling rate required. i) ii) Find minimum bit rate required in the PCM signal. Find the number of bits in each PCM word. iii) iv) Find the minimum absolute channel bandwidth required for the transmission of the PCM signal.5- Discuss the effect of changing the number of bits on the recovered analog waveform. 6- Discuss the effect of changing the frequency of input analog signal on the reconstructed analog output signal.