Use the graphical method to construct the shear-force diagram and identify the magnitude of the largest shear force (consider both positive and negative). The ground reactions are provided. P = 50 kN w = 14 kN/m L = 2m Ay = 38.00 KN Dy=40.00 KN L O 33.7 kN O 29.5 KN O 55.0 KN 43.2 kN O 40.0 KN L W L

Use the graphical method to construct the shear-force diagram and identify the magnitude of the largest shear force (consider both positive and negative). The ground reactions are provided. P = 50 kN w = 14 kN/m L = 2m Ay = 38.00 KN Dy=40.00 KN L O 33.7 kN O 29.5 KN O 55.0 KN 43.2 kN O 40.0 KN L W L

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

For a 2.0 m wide and 0.40 m thick beam on elastic founda- tion, determine the coefficient of subgrade reaction k using Eqs. (10.45) and (10.46), assuming the following param- eters: E, = 30 MN/m², Ep = 30,000 MN/m², µ, = 0.25. %3D
40KN/m 4.5m 7.5m 21 B 1 E=20000MPa 1-1.61x10^6 sqmm Analyze the structure using Consistent Deformation Method. Draw Shear and Moment Diagram (SHOW COMPLETE SOLUTION)
Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Consider the figure shown. Given: P= 24 kN. 24 KN 12 kN/m D E A B 1.8 m 0.6 m'0.6 m 0.6 m Determine the maximum.obsolute values of the shear and bending moment. IML = KN RN m
Determine the flexural stresses using transformed-area method. 2 #25 70 mm 560 mm M = 300 kN• m n = 9 700 mm 4 #32 70 mm 400 mm
1. For the beam loaded as shown, determine the displacement at C midway between the supports by double-integration method. 4.0 KN/ m 4.0 KN/ m 1.0 m B. 1.0 m 2.0 m 2.0 m
SHEAR STRESS 2 If the T-beam is subjected to a vertical shear of V = 60 kN, determine the maximum shear stress in the beam. Also, compute the shear-stress jump at the flange-web junction AB. Sketch the variation of the shear-stress intensity over the entire cross section. VQ TBI = It (60 kN)Q 100 mm 100 mm 75 mm 100 mm I(300) B' VQ TR = It VQ B 150 mm I(100) V = 60 kN
The T section is shown in Figure below is the cross-section of a beam. The beam is subjected to a uniform distributed load = 4 kN/m. The N.A is located at 34.7 mm from the bottom and that IxA =10.64x106 mm. Determine (a) the maximum shearing suess (b) the shearing stress at 15 mm from the bottom face. Q2 %3D 20mm 4 kN/m 120mm A 34.7 mm 20mm lm 3m 1m 220mm TT
Construct the shear -force diagram and identify the largest negative shear force. Assume a = 3.1 ft, b = 6.2 ft, c= 12.4 ft, W= 1200 1b/ft. and Pa 1200 1b,
Construct the shear-force diagram and identify the largest negative shear force. Assume a = 5.8 ft, b = 11.6 ft, c = 23.2 ft, w = 1060 Ib/ft, and P = 2800 Ib. A C D a b
SHEAR STRESS 2 If the T-beam is subjected to a vertical shear of V = 60 kN, determine the maximum shear stress in the beam. Also, compute the shear-stress jump at the flange-web junction AB. Sketch the variation of the shear-stress intensity over the entire cross section. VQ TRỊ = It 100 mm (60 kN)Q 100 mm 75 mm 100 mm I(300) B' VQ TB = VQ 150 mm It I(100) A V = 60 kN
PROBLEM 1 Find the support reactions and joint force of the construction. shown on the figure, if P 12 kN, 4 q=9 kN/m. M 12 kN and L=2 m %3D %3D 21 L.
NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Consider the figure shown. Given: P = 25 kN. A P 24 kN C D E 0.6 m 0.6 m 0.6 m kN-m 12 kN/m B -1.8 m n― Determine the maximum absolute values of the shear and bending moment. VImax KN |Mimax