The 580-kg uniform beam is subjected to thethree external loads shown. Compute thereactions at the support point O. The x-y planeis vertical. Positive values are to the right, up,and counterclockwise.10m +7.2 KN1.9 m40 kN-mB1.9 m3.6 KN Answers:Ox =Oy =Mo =KNkNkN•m

Answered: Image /qna-images/answer/a747c557-9bb7-42b4-ab04-2c387dddad39.jpg

The 580-kg uniform beam is sub three external loads shown. Con reactions at the support point O is vertical. Positive values are to and counterclockwise. 0 1.0 m- 7.2 KN 1.9 m 40 kN-m B 1.9 m C 3.6 KN

The 580-kg uniform beam is sub three external loads shown. Con reactions at the support point O is vertical. Positive values are to and counterclockwise. 0 1.0 m- 7.2 KN 1.9 m 40 kN-m B 1.9 m C 3.6 KN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The concrete floor of a hand regulator is level with the channel bed and is 13 m long. The depth of…

Q: Analysis of Doubly Reinforced Beams Problem 1. Compute the flexural strength of the beam shown. For…

A: The following are the given details. For concrete, fc'=20.70 MPa For steel, fy=276 MPa Section - (a)…

Q: Need 1 m3 of 35 N/mm2concrete (specified compressivestrength). From testing a representative sample…

A: Given: Quantity of fine aggregate needed = 477 kg in dry condition Total moisture of fine aggregate…

Q: 4- In the gate design, the plate considered as a slab simply supported on tow beams. 5- The depth of…

A: This question is related to the Water resources and Open channel flow from Civil Engineering. This…

Q: In a proposed reservoir, the areas containing within the contours are:- Using the method of end…

Q: A rectangular concrete beam 120 x 300 mm is prestressed by straight cable, effective force 180 kN at…

A: Given:- Rectangular concrete Beam 120×300 mm Effective force (P) = 180KN Eccentricity (e) = 50mm…

Q: The concrete floor of a hand regulator is level with the channel bed and is 13 m long. The depth of…

A: Given Data Length of floor (b) = 13m Depth of U/s pile = 2.5 m Depth of D/s pile = 2m F.S.L =…

Q: Determine the product of inertia about the x-y axes of the circular area with the three equal square…

A: Given: Circular area with three square holes

Q: Q5: The following data of a cross regulator. calculate the length of impervious floor of regulator…

A: To find - Length of floor with safe exit gradient of 0.2

Q: (a) A rectangular channel 2.0 m wide has a discharge of 250 lit/sec which is measured by a right…

Q: Can you explain how did that happen the one that is written in blue ballpen? Thank you

A: Explanation is required in some steps.

Q: Find Pace for data shown in table below which below represents speed spot study (SSS) data that…

Q: Torsion A square beam of size 400 mm x 400 mm is subjected to a factored bending moment and twisting…

Q: What force is required to punch 20-33 diameter hole in a plate that is 25mm thick? The shear…

Q: A Trapezoidal canal is designed in alluvial soil using Lacey's theory to fulfill the irrigation…

Q: The beam in Fig 5-1. is used to support a dead load "self weight of 0.8 kN/m, a live load 4 kN/m,…

Q: in a BOD test, 1.0 ml of raw sewage was diluted to 100 ml and the dissolved oxygen concentration of…

Q: A 10 kN/m 8m B 2 m 20 kN

Q: Calculate the design moment for the given beam

A: Answer Design Moment for given beam is Maximum Moment on beam due to given loading. For uniformly…

Q: A 2 m drawdown was observed in a confined aquifer. What would be the drawdown if the…

A: Answer We know that discharge from confined aquifer is given by Q = 2πTSlogeRr Q = discharge…

Q: Three reservoir are connected as shown in figure 1. What is the discharge in each line? All pipes…

A: The given figure is shown below:

Q: FLUID FLOW IN PIPES I. Proving. SHOW THAT 7.05 = √5 + √5 8

A: Given and to prove,

Q: Assuming all dimensional lumber framing, list all elements that will see shrinkage in the vertical…

A: 1. Assuming all dimensional lumber framing, the following elements will see shrinkage in the…

Q: 9. A pump, which has characteristics such in Table 1 is used to deliver water from 2 reservoirs…

Q: a. If the tension in the cables is 150 kN, determine the reaction at the fixed end at E. b. For what…

Q: A steel rod is rigidly attached to two walls as shown in the figure. If origin al temperature (T1)…

Q: 4. A cantilever beam is carrying a 15 kN/m uniformly distributed load over its length of 5 meters.…

Q: M 2 12 ft w = 30 lb/ft 12 ft

Q: A solid circular shaft of diameter d and length L is fixed at one end and free at the other end. A…

A: Given a solid circular shaft with, Diameter d. Length L is fixed at one end and free at another end.…

Q: I. Proving. SHOW THAT 2 1 5. v = ² R³²S² → hf = 10.29n² LQ2 D16/3 6. v=0.849CD2.63 0.54 → hf =…

Q: The infiltration capacity in a basin is represented by Horton's equation as fp-3+eWhere fp is in…

Q: Directions: Find and locate the equivalent concentrated load(s) for the uniformly distributed…

Q: Problem 7 The cantilever truss is part of vertical support system subjected to dead loads (D) and…

A: As per Bartleby's guidelines we are supposed to answer only first three questions. Kindly repost…

Q: A distributary channel having bed width 5.00 m and full supply depth of 1.20 m carries 3.0 m³/s of…

Q: A company that manufactures pulse Doppler insertion flow meters uses the Straight Line method for…

A: An asset's book value is its value as expressed by the balance in its balance sheet account. Asset…

Q: reinforced concrete beam, b by h with tensile reinforcement of 6-25mm diameter bars is simply…

A: 1. To compute the moment capacity of concrete in kN-m, we need to first determine the concrete…

Q: Determine the surface area of a settling tank for 0.5 m³/s design flow using the design overflow…

Q: If wheat requires 7.5 cm of water after every 28 days and the base period of wheat is 140 days, what…

A: Given: Wheat requires 7.5 cm of water after every 28 days. D=7.5 cmt=28 days Base period of wheat, B…

Q: Isosceles traingle gate AB is hinged at A and weights (155 kg) What horizontal force P is required…

Q: Explain why when the temperature decreases the detention time in slow- mix tank increases

A: When the temperature drops, the water will become more viscous because of the drop in temperature.…

Q: A cantilever beam is carrying a 15 kN/m uniformly distributed load over its length of 5 meters.…

Q: A WF16x67 is made from A572 grade 50 steel. A ¾ in. cover plate, 9in. wide, is welded to the top…

A: To find the plastic moment strength of the beam in ft-kips, we need to first determine the plastic…

Q: Calculate the forces in members BC, BE, and EF. Solve for each force from an equilibrium equation…

Q: Calculate the average skid resistance of the pavement surface when a vehicle travelling at a speed…

A: Given that :- Length of skid marks = L = 6 m Speed of the vehicle = u = 35 kmph Calculate the…

Q: The solid shaft is subjected to the distributed and concentrated torsional loadings shown. Determine…

Q: By what means does activated charcoal decolorize dye in wastewater? How does activated charcoal…

A: Activated Charcoal decolorize dye is the most effective method of removing certain organic…

Q: Determine the overall column length that, if exceeded, would cause the column to buckle elastically…

A: Answer To calculate the overall column length which causes the column to buckle elastically before…

Q: The reactions at A and B for the "weightless" beam shown in the figure. The internal forces/moments…

Q: A pre tensioned concrete beam 100 mm wide and 300 mm deep, initial force of 150 kN at an…

A: Given 100 mm wide 300 mm deep Initial force P =150 kN at eccentricity e = 50 mm Moment of inertia…

Q: A WF16x67 is made from A572 grade 50 steel. A ¾ in. cover plate, 9in. wide, is welded to the top…

A: (a) No plate on top A WF16x67 beam without a cover plate may have its plastic moment strength…

Question

The 580-kg uniform beam is subjected to the
three external loads shown. Compute the
reactions at the support point O. The x-y plane
is vertical. Positive values are to the right, up,
and counterclockwise.
10m +
7.2 KN
1.9 m
40 kN-m
B
1.9 m
3.6 KN

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the flexural stresses in the beam section using transformed-area method. M. 100 kN m 10 25 mm 40 250 mm 450 mm 150 mm 250 mm 600 mm
A rectangular beam has the following properties: b = 300 mm, d = 350 mm, tension bars As = 4-28mmØ,compression bars As’ = 2-28 mmØ, d’ = 60 mm. Fc’ = 30 MPa and fy = 345 MPa Determine the design strength of the beam.a. 233.155 kN.m. c. 636.511 kN.m.b. 332.511 kN.m. d. 755.321 kN.m. Calculate the ultimate axial load capacity of a round spiral column having a diameter of 400 mm reinforced with 6-20 mm Ø bars having fc’ = 24 MPa and fy = 276 MPa a. 1941.401 kN c. 1841.321 kNb. 9141.401 kN d. 8141.321 kN Please answer asap.
A reinforced concrete beam has a width of 300mm and a overall depth of 500mm. The beam is simply supported over a span of 5m. Steel strength is 420 Mpa and concrete strength is 28 Mpa concrete cover is 60mm from the steel area, As = 2000mm^2 %3D Determine the maximum factored moment of the beam What is the factored load that the beam can carry Select the correct response: Mu 288.17 KN-m Wu = 92.21Kn/m Mu = 288.17 KN-m Wu = 73.19Kn/m Mu = 320.18 KN-m, Wu = 102.46Kn/m Mu = 288.17 KN-m Wu = 65.86Kn/m
Question 1 A horizontal beam AB with cross-sectional dimensions (b= 0.75 in.) x (h= 8.0 in.) is supported by an inclined strut CD and carries a load P= 2,700 lb at joint B. The strut, which consists of two bars each of thickness 5b/8, is connected to the beam by a bolt passing through the three bars meeting at joint C. (a) If the allowable shear stress in the bolt is 13,000 psi, what is the minimum required diameter of the bolt at C? (b) If the allowable bearing stress in the bolt is 19,000 psi, what is the minimum required diameter of the bolt at C? b- 5 ft Beam AB (b x h) OB h Bolt (dmin) 3 ft P h 2 5b D Strut CD
The simply supported beam consists of a W530 x 66 structural steel wide-flange shape [E = 200 GPa; 1= 351 x 10 mm4]. Determine (a) the beam deflection at point. A. (b) the beam deflection at point C. Assume P = 46 kN, w = 94 kN/m, LẠB=4.0 m, Lec=4.0m, Lco=4.0 m, LDE = 2.0 m. A Answer: VA= Vc= LAB B LBC mm mm LCD W O LDE E x
SITUATION B: The beam is to carry an Ultimate Moment of 580 kN-m, geometrical property of the beam are the following: width of the beam = 350 mm, total height of %3D the beam = 670 mm , steel cover = 50mm. Use concrete strength f'c=21 MPa, steel %3D yield strength fy = 415 MPa and Ø = 0.877 %3D %3D 6. What is the distance of the neutral axis from the extreme compression concrete in mm?
The simply supported beam consists of a W530 × 66 structural steel wide-flange shape [E = 200 GPa; 1 = 351 x 10 mm4]. Determine (a) the beam deflection at point. A. (b) the beam deflection at point C. Assume P = 46 kN, w = 94 kN/m, LAB= 4.0 m, Lec=4.0 m, Lco=4.0 m, LDE = 2.0 m. A Answer: VA = Vc = LAB B LBC mm mm LCD W LDE E x
3. A wide flange section has the following properties: bf = 178.55 mm tf = 12.88 mm L = 10 m tw = 9 mm d = 385.41 Support: Simply supported a. Determine the safe uniform load that the section could carry. b. Determine the shear flow of the portion of the flange 17.50 mm from the edge. c. Determine the maximum deflection of the section.
The cantilever beam consists of a rectangular structural steel tube shape [E = 204 GPa; I = 80 × 106 mm4]. For the loading shown, determine the beam deflection at point B.Assume wAB = 70 kN/m, wBC = 35 kN/m, P = 20 kN, Q = 55 kN, LAB = 1.7 m, LBC = 2.8 m.
4. A restrained beam is subjected to a loading distribution shown below. Determine: a. the location of the maximum deflection, b. the maximum deflection, c. the reactions at fixed supports, and d. the maximum wo that can be applied if the maximum allowable deflection is L/360. w=w,cos(Tx/2L) Figure 4.4
A rectangular beam has the following properties: b = 300 mm, d = 350 mm, tension bars As = 4-28mmØ, compression bars As’ = 2-28 mmØ, d’ = 60 mm. Determine the design strength of the beam.a. 233.155 kN.m. c. 636.511 kN.m.b. 332.511 kN.m. d. 755.321 kN.m. Calculate the ultimate axial load capacity of a round spiral column having a diameter of 400 mm reinforced with 6-20 mm Ø bars having fc’ = 24 MPa and fy = 276 MPa. a. 1941.401 kN c. 1841.321 kNb. 9141.401 kN d. 8141.321 kN
The beam is 7m long with EI = 200MNm^2 Let P = 10 kN Find: 1. Slope at 2m from A. 2. Deflection at 2m from A.