Two links are connected by a single pin and a tensile force F is applied. The links and the pin are made from Aluminum(sigma_y = 35ksi and T_y = 20ksi). The dimension of the link is 5 inch high by 0.5 inch thick. Find the optimal diameter for the pin and the maximum force,F that can be applied to the linkage before incuring permanent deformation.

Two links are connected by a single pin and a tensile force F is applied. The links and the pin are made from Aluminum(sigma_y = 35ksi and T_y = 20ksi). The dimension of the link is 5 inch high by 0.5 inch thick. Find the optimal diameter for the pin and the maximum force,F that can be applied to the linkage before incuring permanent deformation.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.8.11P: A joint between two glass plates A and B is filled with a flexible epoxy that bonds securely to the...

See similar textbooks

Similar questions

A joint between two glass plates A and B is filled with a flexible epoxy that bonds securely to the glass. The height of the joint is/p = 0.5 in, its length is L = 30 in, and its thickness is/ = 0.5 in. Shear force of I' = 25 kips is applied to the joint. Calculate the displacement of the joint if the shear modulus of elasticity G of the epoxy is 100 ksi. Calculate the average shear strain in the epoxy.
You are in charge of designing a new fixture for a “universal testing machine” that will attach a tensile specimen to the machine using a clevis—a U-shaped piece with holes drilled through the two arms—and a cylindrical pin that passes through the clevis and the specimen. If the maximum load exerted by the machine is 30 kN and the pin is to be made of some sort of steel, what is the minimum pin diameter needed to ensure that the shear stress in the pin does not exceed 600 MPa? Assume that the steel has similar elastic properties to pure Fe.
Let's considera rod having a solid circular cross-section with diameter of 4 mm and it is made of a material having a Young's modulus E= 200 Gpa and a Poisson's ratio of 0.3. If a tensile force Fis subjected to that rod cross-section, the diameter becomes 3.995 mm. determine the applied force F Select one: OF 5236 N O F=15708 N Clear mopshoe Finish attempt
When a bar of 22 mm diameter is subjected to an axial pull of 60 kN the extension on the 49 mm gauge length is 0.1 mm and there is a decrease in diameter of 0.013 mm. Calculate the Young's Modulus. Provide your answer in GN/m2 to the nearest whole number.
A cylindrical specimen of 1018 steel having a diameter of 6.35 mm and a gauge length of 38.1 mm is pulled in tension. Use the load-elongation characteristics tabulated below. The modulus of resilience (Ur) is the area under the engineering stress-strain curve. Compute the Ur.
The shaft is pulled by force F. Shaft The yield strength of the material is 500 MPa and the factor of safety is 2 Spindle length 1 m Size the shaft as the outer diameter / inner diameter ratio is 1.5 Note:show the calculations in detail
A cylindrical specimen of a steel alloy having a diameter of 12.8 mm and a gauge length of 50.8 mm is pulled in tension and generates the stress-strain relationship shown in the figure below. Based on this information, a screw is to be designed with a safety factor of 2.5 and to handle an applied force of 8,230N. What would be diameter of the stem/shank of this screw (in mm) when it is designed? Enter your answer to 1 decimal place e.g. 1.2 Hint: Use the yield strength matched from the curve on this homework where you had to find the yield strength at an offset. 600 500 400 500 300 400 300 200 200 100 100 0.000 0.002 0.004 0.006 Strain 0.00 0.04 0.08 0.12 0.16 0.20 Strain Figure 7.33 OJohn Wiley & Sons, Inc. All rights reserved. Stress (MPa) Stress (MPa)
You are given a square rod of 6061-T6 aluminum (cross-section = 4mm X 4mm, length = 2.3m). The material has a Young’s modulus of 72 GPa. If a tensile load of 3 kN is applied parallel to the 2.3m dimension, what is the change in length of the rod?
If an isotropic material has a Young's modulus of 120 Gpa and a Poisson's ratio of 0.3, calculate its shear modulus. Select one: O G= 25 Gpa O G= 46 Gpa O G = 77 Gpa O G= 39 Gpa O G= 29 Gpa
One piece is made of a metal alloy with a yield limit of 180 MPa. At a certain point in the part that is under a flat state of tension, it is known that one of the main stresses is compressive and is half the magnitude of another main stress, which is tensile. Specify the maximum magnitude that the traction component can have, considering that the project requires the adoption of a safety factor 2.0 against flow, according to the criteria of Von Mises and Tresca.
Please solve the problem with a neat paper sheet. The length AB for the lug wrench shown below is 12 inches. What is the maximum force (F) that one can apply on the handles without yielding the material (Steel: Sy = 45 ksi). The diameter of the wrench is 0.625 inch.
A tensile force of 100 kN is applied on a 0.02-m diameter and 2-m long rod. After applying the load, the diameter of the rod decreases to 0.01998 m and the length increases to2.01 m. The true axialstrain is?