The switch in Fig. 7.43 has been in position A for a long time. Att = 0,the switch moves to B. Determine (r) for r>0 and calculate its valueat t = 1 s and 4 s.24 V3 k310A 805 F30 V

We need to find out the voltage across capacitor for given circuit.

Answered: The switch in Fig. 7.43 has been in…

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

7:44 ( Teams PBL-1 Your Friend Saad was selected to attend the Electronics workshop on “Electronic Circuits" organized by the university. In the workshop, he was exposed to many topics such as voltage divider circuits, dependent voltage source, dependent current source, independent voltage source, independent current source, application of Thevenin and Norton theorem, maximum power transfer. There were some customers’ requirements same were discussed in the workshop. Apply the concepts of the above-mentioned topics, each participant must fulfill the customer requirements. I) The input available DC voltage is 220 V and customer wants to supply the output of 30V and 50V. The available ready stock is source voltage as mentioned above and resistors values can be chosen from 1-300 KQ. Apply the concept of voltage divider with values of resistance is in k2, one value of the resistor is the last digit of your NUTECH ID and other may vary (depend on your calculations). II) Now you have two…
P7-12 7-13 The circuit in Figure P7-13 contains two energy storage SS devices connected to a battery via a single-pole, double-throw switch (SPDT). The switch has been in position A for a long time. At t=0, the switch moves to position B. After 5 ms, it moves back to position A. If R₁ = 1 k2, C = 1 μF, Vs = 10 V, R₂= R3 = 100 S2, and L=100 mH, plot voi(t) and voz(1) from t=0 to 1= 10 ms. A BR₂ • W t=0 iL (1) + 1=5 ms + Vor (1) R₁ CVs R3L02 (1) с FIGURE P7-13
7.7μF capacitor is charged by a 125V battery and then is disconnected from the battery. When this capacitor (C1) is then connected to a second (initially uncharged) capacitor, C2, the final voltage on each capacitor is 15V. What is the value of C2? [Hint: Charge is conserved.]
7. Problem 7.9: The switch opens at t = 0. Find vo fort>0 -t 0 2 k2 15 V + C4 k2 Vo 3 mF
In the circuit of Fig. 7_1, what is Leq? -Lea] m 5777. 4H a b 8H 4H 10H Fig. 7_1 2H O Leg-7 H OL-17 H OL-SH O Log-15 H OL-20 H OL-32 H 4H m m 2H
Complete the values of the following circuits. Show complete solution thanks
7.5 From the circuit in the figure, if the switch is touched at position a for a long time and then moved to touch position b at the time t = 0 Find i(t) when t > 0.
1. 7.21 The switch in the circuit has been in the left positionfor a long time. At t=0 it moves to the right position and stays there 3. c) Find the time constant of this circuit for t>0.
We wish to carry out a subtraction using the circuit shown below. We will subtract A - B where A = 4 and B = 7. Assuming the everything is operating correctly with the circuit, determine the following values: The input to the 7483 chip at B3 is 1 (High) or 0 (Low) The output Σ4 Σ3 Σ2 Σ1 is 1 (High) or 0 (Low)
Problem 7-4. For the circuit shown in figure P7.4, determine v₁(t), vc(t) and ix(t) for t≥ 0+. Assume that the switch has been in its starting position for a long time before moving at t = 0. 100Ω www 0.3A (1 t = 0 0.5mH 0.2μF + VL(t) Vc(t) 'T' (609)ix
1. 7.7 The switch in the circuit has been closed for a long time. At t=0 theswitch opens and stays open. Find the expression for vo(t) for t≥0.
T or F The 'Constant Source Block produces a constant signal with a default value of zero. Manual control system is also known as open loop control system. If the damping factor is zero, the unit-step response is a Purely sinusoidal.

SEE MORE QUESTIONS

Recommended textbooks for you

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Fundamentals of Electric Circuits

Electrical Engineering

ISBN:

9780078028229

Author:

Charles K Alexander, Matthew Sadiku

Publisher:

McGraw-Hill Education

Electric Circuits. (11th Edition)

Electrical Engineering

ISBN:

9780134746968

Author:

James W. Nilsson, Susan Riedel

Publisher:

PEARSON

Engineering Electromagnetics

Electrical Engineering

ISBN:

9780078028151

Author:

Hayt, William H. (william Hart), Jr, BUCK, John A.

Publisher:

Mcgraw-hill Education,

SEE MORE TEXTBOOKS

The switch in Fig. 7.43 has been in position A for a long time. At t=0, the switch moves to B. Determine (r) for r>0 and calculate its value at t = 1 s and 4 s. 24 V 3 k 360 1-0 B 0.5 mF 30 V