1- A 12.4-kV single-phase generator supplies power to a load through a transmission line.The load's impedance is Zload -500236.87° 2, and the transmission line's impedance isZline = 60260° as in the figure below. Calculate:The line current;(i)(ii) The load voltage:(iii) The ratio of the load voltage to the generated voltage:(iv) The transmission losses of the systemVG = 12.4~VG12.420 kV60260°02Zine500L 36.87°2 Zload

1- A 12.4-kV single-phase generator supplies power to a load through a transmission line. The load's impedance is Zload -500236.87° 2, and the transmission line's impedance is Zline = 60260° 2 as in the figure below. Calculate: (i) The line current; (ii) The load voltage; (iii) The ratio of the load voltage to the generated voltage; (iv) The transmission losses of the system 60260° Ω VG= 12.420 kV 500Z 36.87°2 Zload

1- A 12.4-kV single-phase generator supplies power to a load through a transmission line. The load's impedance is Zload -500236.87° 2, and the transmission line's impedance is Zline = 60260° 2 as in the figure below. Calculate: (i) The line current; (ii) The load voltage; (iii) The ratio of the load voltage to the generated voltage; (iv) The transmission losses of the system 60260° Ω VG= 12.420 kV 500Z 36.87°2 Zload

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.41P

See similar textbooks

Similar questions

The p.u. impedance value of an alternator corresponding to base values of 13.2 kV and 30 MVA is 0.2 p.u. Then the p.u. impedance value of an alternator for the new base values of 13.8 kV and 50 MVA is......
What is the main direct cause of reactive power in AC system?A. Resistance of transmission linesB. Inductance and capacitance in the loadsC. Ideal transformer connected in the systemD. Power produced by generator
The reactance of a generator is given as 0.25 per-unit based on the generator’s of 18 kV, 500 MVA. Find its per-unit reactance on a base of 20 kV, 100 MVA. a. 0.0505 b. 0.0605 c. 0.0405 d. 0.0606
Q2) A 13.2-kV single-phase generator supplies power to a load through a transmission line. The load's impedance is Ztoad 500 236.87° ohm , and the transmission line's impedance is Zine = 60 253.1° ohm. To reduce transmission line losses to 0.0103 of its losses without using the transformers design and use two transformers T1 between the generator and the transmission line and T2 between the transmission line and the load.
As seen in the figure, three generators of 800 kW, 900 kW and 1000 kW are connected in parallel. It generators feed 380 kW load. Frequency-active power graphs of generators are shown as given. According to this; a. Calculate the operating frequency for the situation given in the question.b. Calculate the power transferred by the generators to the load.c. A three-phase asynchronous load of 800 kW and 600 kVA with a reverse power coefficient of 0.78 is installed in the system. engine is connected. The new operating frequency of the system and the active power of the alternators. calculate.d. Do you think the generators in this system are suitable for parallel connection as in the figure?
The 13.2 kV 50-Hz generator feeds a load over a line with (Zload) impedance Zline. Load is 800n + j500n and impedance of the line is 20 + j300 a) If the generator is directly connected to the load as given in (a), what will be the line losses? b) If the generator is connected to the load using step-up and step-down transformers as given in (b), what will be the line losses? c) How much is the increase in efficiency compared to (a) from (b)? Zline 2. (a) 1:10 10:1 Zline Tr Tr2 (b) Zload Zload
4. An Open-Wye/Open-Delta transformer, as shown in Figure, is formed by two identical single-phase transformers. The primary line-to-line voltage is 12.47 kV, and the secondary line-to-line voltage is 208 V. Take
Q2) A 13.2-kV single-phase generator supplies power to a load through a transmission line. The load's impedance is Zload = 500 236.87° ohm, and the transmission line's impedance is Zline = 60 253.1° ohm. To reduce transmission line losses to 0.0103 of its losses without using the transformers design and use two transformers T1 between the generator and the transmission line and T2 between the transmission line and the load.
1. A single-phase power system as shown in Figure 1 consists of a 240 V, 60 Hz generator supplying a load, Zod = 8 + j6 Q through a transmission line of impedance, Zne = 0.08 + j0.14 Q. Answer the following questions: (1) transformer, T; and T2. Determine the voltage at the load and transmission line losses without the (ii) Determine the voltage at the load and transmission line losses with the transformer, T, and T2. T1 T2 1:10 10:1 IG Zaine Zioad source Figure 1
In a Three-phase alternator, a given field current produces an armature current of 250 A on short-circuit and a generated e.m.f. of 1500 V on open-circuit. Calculate the terminal p.d. when a load of 250 A at 6.6 kV and 0.8 p.f. lagging is switched off. Calculate also the regulation of the alternator at the given load. Subject: Electrical engineering
A synchronous generator has been synchronized to an infinite grid of 13.8 kV and 60 Hz. The generator prime mover C/C is such that the no-load frequency is 62.5 Hz and the power slope is 1 MW/Hz. The AVR C/C (The reactive power against the terminal voltage C/C) is such that the zero reactive power voltage is 14.6 kV, while the slope is 0.4 MVAR/kV. Calculate: (a) the kVA loading of the generator and its power factor. (b) the settings of the prime mover and AVR such that the generator delivers 3 MW at 0.85 lagging power factor.
The reactance of a generator is given as 0.1 pu based on the generator of 17 KV, 300 MVA. Determine the pu reactance on a base of 17 KV, 250 MVA. New pu reactance is.......