The split ring shown has an inner radius ₁0.6 in. and a circular cross section of diameter d= 0.8 in. Knowing that each of the 105-lb forces P is applied at the centroid of the cross section, determine the stress at point A and at point B. B The stress at point A is 6.143 ksi. The stress at point Bis -3.380 ✪ksi.

The split ring shown has an inner radius ₁0.6 in. and a circular cross section of diameter d= 0.8 in. Knowing that each of the 105-lb forces P is applied at the centroid of the cross section, determine the stress at point A and at point B. B The stress at point A is 6.143 ksi. The stress at point Bis -3.380 ✪ksi.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

6kN and 1.0KNM loads are applied to the top of the 62-mm-diameter cast-iron as shown. Determine the principal stresses (max and min normal stresses), principal planes (orientation of plane for max-min normal stresses) and max shear stress by using Mohr's circle. Hint: Use given coordinate system. So, H is on x-z plane and K is on y- z plane 1.0 kN.m 6 kN X 220 mm
Draw Mohr's circle that describes each of the following states of stress. (C.) M 6 ksi 12 ksi
Given the plane element shown which is an element acted upon by combined stresses. a. Use Mohr's Circle to determine the maximum shear stress on the element b. Also, using Mohr's Circle determine the maximum normal stress on the element.
Determine the state of stress at point A of the rectangular post shown loaded with concentrated forces directed along the y axis equal to 75kN and along the x axis equal to 15kN. 75 KN a) Determine the equivalent internal forces and moments at the section containing points A 50 mm F₂= Fy= F₂= M₂= M,= M,= b) Determine the total normal stress along the x and y axes at point A (include if tensile or compressive in your final solutions) σμ² ƠAy² c) Determine the total shear stress at point A TA= d) Draw the state of stress of point A 15 KN 200 mm A 150 mm 50 mm 800 mm
1. The box beam is subjected to the loading shown. Determine the principal stresses in the beam at point A. 6 in. 800 lb AH 6 in. 8 in. '8 in. A -3 ft--2.5 1200 lb +-2.5 ft---2.5 ft-|- -5 ft-
For the structure shown, determine the following: a. The normal and shear stresses in section (ksi) b. The maximum normal stress in member BC (ksi) c. The maximum bearing stress on member AB (ksi) Pins A & C have a diameter of 34 in while pin B has a diameter of ½ in. Both members have a thickness of 0.4 in. There are two support plates at A. 1.5 in. B C 60° 8 ft 2 kip/ft A
Two loads P act as shown, one parallel to x and another parallel to z axes; each load P equals 1850 N. The crankshaft dimensions are b1 = 85 mm, b2 = 130 mm, and b3 = 60 mm. The diameter of the upper shaft is d = 28 mm. Determine the normal stress at point B, which is located on the surface of the upper shaft at the y axis. Lütfen birini seçin: a. 121.465 MPa b. 287,937 MPa O c. None O d. 149.606 MPa e. 324.676 MPa
3. FOR THE STATE OF STRESS SHOWN, DETERMINE THE ON THE INCLINED PLANE A--A. STRESS COMPONENTS ACTING 40 MPa 60 MPa 30
The normal stress on the rectangular cross sec- varies linearly with respect to the tion ABCD y coordinate. That is, o, has the form o, = a + by, varying lin- early from oxb at the bottom edge of the cross section to ơxt at the top edge of the cross section. (a) Show that M, = 0 for this symmetrical normal-stress distribution. (b) Determine an expression for the axial force F, in terms of the stresses Oxb and ox and the dimensions of the cross section, width b and height h. (c) Determine an expression for the correspon- ding value of the bending moment M.
Assume that the magnitude of the vertical force P is 2.5 kN. Determine the stress at point A and B
1. Determine the equivalent state of stress on an element at the point which represents, the principal stresses and, the maximum in-plane shear stress and the associated average normal stress. Also, determine the corresponding orientations of the element. a. Use Equation Method b. Use Mohr's Circle 28 MPa 14 MPa 7 MPa
1200 N 2. For the bone shown to the left, assume the cross-section at C can be approximated as annular, with an outer diameter of 25mm. When the 1200 N forces are applied, the average normal stress in the bone at point C is determined to be 3.80 MPa. Determine the inner diameter of the bone cross section at C. Ans: d; = 14.93 mm 4 in. P 3 in. B 1200 N "UI 8