For the state of a plane strain with Ex, Ey and yxy components: (a) construct Mohr's circle and (b) determine the equivalent in-plane strains for an element oriented at an angle of 30° clockwise. Ex = 250 x 10-6 Ey = 310 x 10-6 Yxy = -100 × 10-6

For the state of a plane strain with Ex, Ey and yxy components: (a) construct Mohr's circle and (b) determine the equivalent in-plane strains for an element oriented at an angle of 30° clockwise. Ex = 250 x 10-6 Ey = 310 x 10-6 Yxy = -100 × 10-6

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.7.3P: An element of material in plain strain is subjected to shear strain xy = 0.0003. (a) Determine the...

See similar textbooks

Related questions

Q: 100 mm 6 in. 200 mm 140 mm 140 mm 2. Locate the centroid (x, y) for the angle's cross sectional…

A: A2 = A2 = A2 = 15707.96 A1 = A1 = 40292.04-> Centroiet of Rectangular point. X1 = 100…

Q: A Scotch yoke is a mechanism that transforms the circular motion of a crank into the reciprocating…

Q: ALT 4/8 Determine the force in each member of the loaded truss. 2m D 4m] 5 kN. B 3 m C 15°

A: To Find-The force in each member of the loaded truss.

Q: A steam power plant is operating on the ideal Rankine cycle. The boiler is maintained at 4 MPa, and…

Q: L Figure 2 B 3√2 Figure 2 A beam AB of length L-1.5 m is supported by a pin at A and a cable BC at…

Q: The cover of a cylindrical pressure vessel made of cast iron is shown in fig.1 The inner diameter of…

A: Given:The inner diameter of the cylinder is .The internal pressure is limited to .The number of…

Q: A slender rod of mass mo = 10.8 kg and length / = 895 mm is welded at its midpoint A to the rim of…

A: Mass of rod,m0=10.8 kgLength of rod,L=895 mm=0.895 mMass of disk,m=24 kgradius of disk,r=345…

Q: a=(3.7m) , b=(3.7m) ,theta =(33) , p1=(3.7)KN , p2=(2.4)KN find the forces in each members…

A: According to the given dataWe need to findforce in each member.

Q: The beam is supported by a pin at Cand by a short link AB. Each pin has a diameter of 26 mm. Assume…

Q: Problem 3 Draw the moment diagram for the beam using the method of superposition. 10 kN/m -8 m B 80…

Q: A model rocket is launched from point A with an initial velocity vo of 84 m/s. Also, the rocket's…

A: The initial velocity of rocket Distance

Q: For an ideal Rankine cycle, steam first enters the turbine at 5 MPa and 500C then it expands to a…

A: The quality of steam, the heat addition, the heat rejected, the turbine work, the pump work, the…

Q: Air at 15°C and 100 kPa occupies 0.03 m³. The air is heated at constant volume until the pressure is…

Q: 100 mm T=? 45° 300 mm 400 mm O 250 mm The mechanism shown in the figure is in static equilibrium.…

A: In the above diagram, is angle of BC with horizontal and is angle of CD with horizontal.

Q: The hydraulic crane is used to lift the 1380-lb load. Determine the force in the hydraulic cylinder…

Q: Determine the axial load in rod (1).

Q: A rectangular block measures 100 mm by 80 mm by 60 mm. Draw a section view of the block with a…

Q: W B A Y Fj FM

Q: Determine the deflection of point B

A: Given DataPortion AB made of steelThe Youngs modulus of the steel The Coefficient of thermal…

Q: The design of a camshaft-drive system of a four-cylinder automobile engine is shown. As the engine…

Q: In an insulated piston-cylinder assembly, there is initially 4 L of saturated liquid water at 200…

Q: The pump in the Rankine cycle increases the pressure from 20 kPa to 6 MPa. The boiler exit…

A: P1 = 20 kPaP2 = 6 MPa or 6000 kPaBoiler exit temperature, T = 600°CRequired:Q ( heat supplied to…

Q: Find the centroid of area of the Z section as shown in the Fig.9. Also, determine the Second Moment…

Q: The basketball player likes to release his foul shots with an initial speed vo= 24.3 ft/sec. What 2…

Q: The design of a camshaft-drive system of a four-cylinder automobile engine is shown. As the engine…

Q: PLEASE ANSWER WITH UNIT!!!!! A copper sphere having a diameter of 2 cm is initially at a uniform…

Q: Refrigerant R134a enters an expansion valve at 800 kPa as a saturated liquid and exits at 100 kPa.…

A: Given:The initial pressure is .The final pressure is .The initial condition is saturated…

Q: Two gears with fixed pins at their (geometric, mass) centers (C₁, C₂) are in mesh as shown. The gear…

Q: A steel rod 22 mm in diameter and 1000 mm long is required to have an elastic strain energy of 90…

Q: Provide a detailed breakdown of the safety and learning features included into the set.

A: It is asked to provide a detailed breakdown of the safety and learning features included in the set

Q: 7. Understand and apply the concept of rolling resistance. (CO-5)

A: Hi,As per the guidelines we can solve first question for you since the exact one is not mentioned.…

Q: A model rocket is launched from point A with an initial velocity vo of 84 m/s. Also, the rocket's…

Q: F= 250N 40 9 Black = 3,5m/52 M= friction Block m= 8kg coefficient btwn black and channel 250M force…

Q: the permissible tensile stress for the belt material is 1.75 MPa, calculate: 1. Diameters of…

Q: Up= 3.23 m S

Q: The figure shows the Russel fracture traction device and a mechanical model of the leg. The leg is…

Q: (c) An electronic PI temperature controller has an output p of 15 mA when the set point equals the…

A: In the problem, the following information was provided:The PI temperature sensor step response is…

Q: A pair of spur gears with 20° tooth form transmits 1.0-hp. The pinion is mounted on the shaft of an…

Q: A car of mass 1200 kg is climbing up a slope of 1 in 8. It is accelerated from 3.0 to 6.0 m/s while…

A: Given data :-Mass of car = 1200 kgSlope = 1 in 8 V1 = 3 m/sV2 = 6 m/sDistance cover = 80 mDiameter…

Q: Types of tirfor machine and their uses?

A: Tirfor Machine:The Tirfor machine, also known as a wire rope winch or a hand winch, is a mechanical…

Q: An accelerometer C is mounted to the side of the roller-coaster car and records a total acceleration…

Q: When filled to capacity, the unpressurized storage tank contains water to a height of h = 39 ft. The…

A: According to the given dataDensity=We need to find The maximum normal stress and The maximum shear…

Q: Please write down Darcy’s law with pressure and potential form separately, explain the meaning of…

A: This law describe the fluid through the porous medium.French engineer Henri darcy governs the law…

Q: 230-kg uniform snart is turned through angle as shown here. End A is walls suppor supported by the…

Q: What are the key factors to consider when designing a Distributed Control System (DCS) for a…

A: Distributed Control System (DCS) is a specialized system used in manufacturing or processing…

Q: i. Carbon Intensity what is this a measure of, what are its units and why is it important? ii.…

A: To explain:i. Carbon Intensity what is this a measure of, what are its units and why is it…

Q: (b) A transistor with a height of 0.4 cm and a diameter of 0.6 cm is mounted on a circuit board as…

A: Height, H = 0.4 cm or 0.004 mDiameter, D = 0.6 cm or 0.006 mAverage heat transfer coefficient, h =…

Q: 4. A household refrigerator with a COP of 1.25 removes heat from the refrigerated space at a rate of…

Q: What are the key advantages and disadvantages of using composite materials in mechanical engineering…

A: Composite materials refer to materials made from two or more constituent materials with…

Q: A force P and a force Q, applied via a nut, are acting on the arm attached to the end of a shaft…

A: The strain reading on the gauge 1 = 630*10-6 The strain reading on the gauge 2 = 630*10-6 The strain…

Question

For the state of a plane strain with Ex, Ey and yxy components: (a) construct Mohr's
circle and (b) determine the equivalent in-plane strains for an element oriented at
an angle of 30° clockwise.
Ex = 250 x 10-6
Ey = 310 x 10-6
Yxy = -100 × 10-6

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given Data

Step 2: To find out

Step 3: Explanations

Solution

Step by step

Solved in 4 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The strains for an element of material in plane strain (see figure) are as follows: x = 480 ×10-6. y = 140 × l0-6, and xy = —350 x 10”. Determine the principals strains and maximum shear strains, and show these strains on sketches of properly oriented elements.
An element of material in plain strain has the following strains: x = 0.001 and y = 0.0015. (a) Determine the strains for an element oriented at an angle = 250. (b) Find the principal strains of the element. Confirm the solution using Mohr’s circle for plane strain.
A strain rosette (see figure) mounted on the surface of an automobile frame gives the following readings: gage A,310 × 10-6:gage B,180 × l0-6; and gage C. -160 × 10-6. Determine the principal strains and maximum shear strains, and show them on sketches of properly oriented elements.
An element of material in plain strain is subjected to shear strain xy = 0.0003. (a) Determine the strains for an element oriented at an angle = 30°. (b) Determine the principal strains of the clement. Confirm the solution using Mohr’s circle for plane strain.
- 7.2-26 The strains on the surface of an experiment al device made of pure aluminum (E = 70 GPa. v = 0.33) and tested in a space shuttle were measured by means of strain gages. The gages were oriented as shown in the figure. and the measured strains were = 1100 X 106, h = 1496 X 10.6, and = 39.44 X l0_. What is the stress o in the x direction?
An element of material in plain strain is subjected to strains x = 0.0015, , y . = -0.0002, and xy = 0.0003. (a) Determine the strains for an element oriented at an angle = 20°. (b) Determine the principal strains of the element. Confirm the solution using Mohr’s circle for plane strain.
During a test of an airplane wing, the strain gage readings from a 45° rosette (see figure) are as follows: gage A, 520 × l0-6; gage B. 360 × l0-6; and gage C,-80 × 10-6. Determine the principal strains and maximum shear strains, and show them on sketches of properly oriented elements.
Solve the preceding problem if the cross- sectional dimensions are b = 1.5 in. and h = 5.0 in., the gage angle is ß = 750, the measured strains are = 209 × 10-6 and B = -110 × 10, and the material is a magnesium alloy with modulus E = 6.0 X 106 psi and Poisson’s ratio v = 0.35.
On the surface of a structural component in a space vehicle, the strains arc monitored by means of three strain gages arranged as shown in the figure. During a certain maneuver, the following strains were recorded: e, = 1100 X l0_6, 6h = 200 X lO_6, and e = 200 X 10-6. Determine the principal strains and principal stresses in the material. which is a magnesium alloy for which E = 6000 ksi and v = 0.35. Show the princ ipal strains and principal stresses on sketches of properly oriented elements.
Solve the preceding problem for the following strains: x=120106,y=450106,andxy=360106.
An clement of material subjected to plane strain (see figure) has strains of x=280106 , y=420106 , and xy=150106 . Calculate the strains for an element oriented at an angle = 35°. Show these strains on a sketch of a properly oriented element.
A solid spherical ball of magnesium alloy (E = 6.5 × l0-6 psi, v = 0.35) is lowered into the ocean to a depth of 8000 ft. The diameter of the ball is 9.0 in. (a) Determine the decrease ?d in diameter, the decrease, ?V in volume, and the strain energy U of the ball. (b) At what depth will the volume change be equal to 0.0324% of the original volume?