The motor causes the aluminum shaft containing gears D, E, and F to rotate. The solid shaft has a diameter of 24 mm and a modulus of rigidity of 24 GPa. The bearings at G suddenly jams, after which gear B rotates an additional 0.27 radians and gear C rotates an additional 0.21 radians. Determine the resulting torsion, T, that must be occurring in the shaft between gears D and E. Assume that D and E are rotating the same direction. Also note that gears B and C both have a 60 mmtradius. Express your answer in Nm to the nearest whole Nm. 100 mm 30 mm 60 mm 40 mm D. 02m 08 m 0.4 m 02 m

The motor causes the aluminum shaft containing gears D, E, and F to rotate. The solid shaft has a diameter of 24 mm and a modulus of rigidity of 24 GPa. The bearings at G suddenly jams, after which gear B rotates an additional 0.27 radians and gear C rotates an additional 0.21 radians. Determine the resulting torsion, T, that must be occurring in the shaft between gears D and E. Assume that D and E are rotating the same direction. Also note that gears B and C both have a 60 mmtradius. Express your answer in Nm to the nearest whole Nm. 100 mm 30 mm 60 mm 40 mm D. 02m 08 m 0.4 m 02 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The wheel is made from a 8-kgkg thin ring and two 1-kgkg slender rods. 0.5 m M If the torsional spring attached to the wheel's center has a stiffness k = 2 N m/rad, so that the torque on the center of the wheel is M = (20) N m, where 0 is in radians, determine the maximum angular velocity of the wheel if it is rotated two revolutions and then released from rest. Express your answer to three significant figures and include the appropriate units. HA Value Units
The A-36 steel assembly consists of a tube having an outer radius of 1 inch and a wall thickness of 0.125 inch. Using a rigid plate at B, it is connected to the solid 1-inch diameter shaft AB. Determine the rotation of the tube’s end C if a torque of 200lb inches is applied to the tube at this end. The end A of the shaft is fixed supported.
Q: Part A: Determine the absolute maximum shear stress in the shaft. Part B: Determine the angle of twist of end EE of the shaft relative to BB. Given: The turbine develops 150 kW of power, which is transmitted to the gears such that CC receives 70% and DD receives 30%. The rotation of the 100-mm diameter A-36 steel shaft is ωomega = 600 rev/min . The journal bearing at EE allows the shaft to turn freely about its axis. The shear modulus of elasticity for A-36 steel is 75 GPa.
The two shafts are made of steel (G=11x106 lb/in2). Each has a diameter of 1 in. , and they are supported by bearings at A, B and C, which allow free rotation. If the support at D is fixed, determine the angle of twist of end A when the torques are applied to the assembly as shown. Torque applied at H of 80 ft lbs, and at G of 40 ft lbs in opposing directions as seen in the figure
Problem 2: Consider the two gears mounted on the shaft, as shown. Distances are L1 = 100 mm, L2 = 250 mm, and L3 = 175 mm. Diameter of shaft AB is 15 mm, diameter of shaft BC is 20 mm, and diameter of shaft CD is 17.5 mm. Young's modulus for each portion is 200 GPa. Determine the displacement of point D with reference to point A. Also, determine the displacement of point A relative to C. b. Determine the axial strain at any point in shaft segments AB, BC and CD, respectively. If Poisson's ratio for the material of the shafts is v = 0.2, determine the lateral strain in each of the shaft segments. Based on your answers to part (a), do the gears move towards each other, or do they separate from each other? Note that in real gearboxes, movement of gears towards or away from each other is prevented by using thrust bearings. 10 kN 4 kN 5 kN 7 kN 4 kN NY 0I 17.
The turbine develops 150 kW of power, which is transmitted to the gears such that C receives 70% and D receives 30%. The rotation of the 100-mm-diameter A-36 steel shaft is a 750 rev/min. The journal bearing at E allows the shaft to turn freely about its axis. The shear modulus of elasticity for A-36 steel is 75 GPa. (Figure 1) Figure 1 of 1 Part A Determine the absolute maximum shear stress in the shaft. Express your answer to three significant figures and include the appropriate units. Tax Value Submit Part B $8/0 Submit Request Answer Determine the angle of twist of end E of the shaft relative to B Express your answer using three significant figures. Provide Feedback VAX Units Request Answer ? Ivec 4 ? rad
In the gear system shown, the motor applies a torque of 290 N-m to the gear at A. Shaft (1) is a solid 35-mm-diameter shaft, and shaft (2) is a solid 50-mm-diameter shaft. The bearings shown allow free rotation of the shafts. Determine the torque TE provided by the gear system at gear E. B 72 teeth 30 teeth TE (2) E 24 teeth 60 teeth
The solid shaft is made from red brass C83400 copper and it is subjected to a torque T = 6 kip · ft at B. 4 in. 2 ft 2 in. B T 2 in. 4 ft Problem 5.108 Draw the Free Body Diagrams and the associated Equilibrium equations. Write the compatibility equation.
A turbine rotor is mounted on a stepped shaft that is fixed at both ends as shown in The torsional stiffnesses of the two segments of the shaft are given by ka = 3,000 N-m/rad and k2 = 4,000 N-m/rad. The turbine generates a harmonic torque given by M(t) = Mo cos wt about the shaft axis with M, = 200 N-m and w = 500 rads. The mass moment of inertia of the rotor about the shaft axis is Jo = 0.05 kg-m. Assuming the equivalent torsional damping constant of the system as c, = 2.5 N-m-s/rad, determine the steady-state response of the rotor, 6(1). O(1) ke M(1) = M, cos ot Turbine rotor, Jo
Please answer: 3, 4, 5, 6, 8, 9, 10, 12 The only correct answers are 1 (0), 2 (0), 7 (point A). #11 is 2. The rest are incorrect. Please do not submit the same answer you submitted for my original question. The wheel is attached to the spring. The mass of the wheel is m=20 kg. The radius of the wheel is 0.6m. The radius of gyration kG=0.4 m. The spring’s unstretched length is L0=1.0 m. The stiffness coefficient of the spring is k=2.0 N/m. The wheel is released from rest at the state 1 when the angle between the spring and the vertical direction is θ=30°. The wheel rolls without slipping and passes the position at the state 2 when the angle is θ=0°. The spring’s length at the state 2 is L2=4 m. (1) If the datum for gravitational potential energy is set as shown below, the the gravitational potential energy of the wheel at the state 1 is 0 N m(two decimal places) (ANSWER IS 0) (2) If the datum for gravitional potential energ is set as shown below, the gravitational potential energy of…
The two 1-kg gears A and B are attached to the ends of al 3-kg slender bar. The gears roll within the fixed ring gear C, which lies in the horizontal plane. (Figure 1) Figure 150 mm 400 mm- 150 mm Part A If a 10-N m torque is applied to the center of the bar as shown, determine the number of revolutions the bar must rotate starting from rest in order for it to have an angular velocity of WAB = 22 rad/s. For the calculation, assume the gears can be approximated by thin disks. Express your answer using three significant figures. ►View Available Hint(s) the number of revolutions = Submit Provide Feedback VAE vec ? Next >
Steel rod AB bonded to the brass rod BCD as shown below. The steel rod has a diameter of 50 mm while the brass rod has an outer diameter of 40mm with segment BC being hollow with an inner diameter of 20 mm. If the assembly is loaded as shown, solve for the a. magnitude of the internal torque in the steel section (TAB) b. maximum shear stress in the steel section (TAB) C. maximum shear stress developed in the whole assembly (Tmax) 0.60 kNm A 1.80 kNm 2.0m 2.0m 2.0m