The lap joint is fastened with four ¾” diameter rivets. The working stresses are 14 ksi for the rivets in shear and 18 ksi for the plates in bearing. Find the maximum safe axial load P that can be applied to the joint. Assume that the load is equally distributed among the rivets. ANS: P = 47.3 kips P P in. 4 in. 710 in. P P

The lap joint is fastened with four ¾” diameter rivets. The working stresses are 14 ksi for the rivets in shear and 18 ksi for the plates in bearing. Find the maximum safe axial load P that can be applied to the joint. Assume that the load is equally distributed among the rivets. ANS: P = 47.3 kips P P in. 4 in. 710 in. P P

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

4-5 The A-36 steel rod is subjected to the loading shown. If the cross-sectional area of the rod is 60 mm², determine the displacement of B and A. Neglect the size of the cou- plings at B, C, and D. 60° 3.30 KN 2 kN D C B A 8 kN 60⁰ 3.30 KN 0.75 m 1.50 m 0.50 m 2 kN
4-43 The center post B of the assembly has an original length of 124.7 mm, whereas posts A and C have a length of 125 mm. If the caps on the top and bottom can be consid- ered rigid, determine the average normal stress in each post. The posts are made of aluminum and have a cross-sectional area of 400 mm². Eal = 70 GPa. A 100 mm- B 100 mm- C 800 kN/m 125 mm 11800 800 kN/m
2. Assume that a 20mmØ rivet joins the plates that are each 110mm wide. The allowable stresses are 120 MPa for bearing in the plate material and 60MPA for shearing of rivet. Determine the minimum thickness of each plate 110 mm 20-mm 0
lho H.W.2: 1,200 mm The load P produces an axial strain of -1,800 pe in post (2). Determine the axial strain in rod (1). (1) rigid plate 480 mm bare 1.5 mm 600 7. 100000\ 300 mm 300 mm 600 mm (2) S. 1,0 8 11 2,09 4 1, nd supported by two rods at A and- E naliad After load Pis applie
Calculate the maximum tensile and compressive stresses in the section of BC of the beam. 75 mm 75 mm Empedopre|72 -75 mm 150 mm 50 mm EN SAMA 00 kN B 1.0 m 60 kN -1.5 m-> rode D 1.0 m
F5. The circular shaft AC is fixed to rigid walls at A and C. The section AB is solid annealed bronze and the hollow section BC is made of aluminum alloy 2024 T-4. There is no stress in the shaft before the 20,000 ft-lb torque is applied. Determine the maximum shearing stress in each shaft after T is applied. Section BC 4 D=4" 20 ft-k 6.5-FE B 5ft Match each item to a choice: TAB TBC 2"
Q3) The beam system has a pin support at A, roller supports at D and F, and internal hinges at C. Find the deformations at C and E using the conjugate beam method. 10 kN A C D E F 100 kN-m k5 mt-5 m--5 m5 m-k10 m- = 100 x 10° mm*, and ICF Given: E = 200 GPa, IAC 50 x 10° mm“. %3D لقطة شاشة
Problem # 3: The strut AB made from two bars (thickness of each bar = 0.50 in) is connected to a rectangular beam CD (b=0.80 in x h = 7.5 in) at joint B. The beam carries a concentrated load of 2750 lb at the end joint D. (a) determine the minimum diameter of the bolt at B if the shearing stress in the bolt is not to exceed 14000 psi. (b) determine the minimum diameter of the bolt at B if the allowable bearing stress in the bar plate is 20000 psi. Detail of joint B 0.80 in 3 ft с VO A 5 ft- + B 6 ft- D 2750 lb 3.75 in 3.75 in Strut AB - Beam CD (b X h) Bolt (dmin) -0.50 in
(6) The tension member is fastened together using two bolts, one on each side of the member as shown. Each bolt has a diameter of 12 mm. Determine the maximum load P that can be applied to the member if the allowable shear stress for the bolts is Tallow 80 MPa and the allowable average normal stress is allow= 120 MPa. A000 60° P
The strut AB made from two bars (thickness of each bar = 0.50 in) is connected to a rectangular beam CD (b = 0.80 in x h = 7.5 in) at joint B. The beam carries a concentrated load of 2750 lb at the end joint D. (a) determine the minimum diameter of the bolt at B if the shearing stress in the bolt is not to exceed 14000 psi. (b) determine the minimum diameter of the bolt at B if the allowable bearing stress in the bar plate is 20000 psi.
= The strut AB made from two bars (thickness of each bar = 0.50 in) is connected to a rectangular beam CD (b 0.80 in x h = 7.5 in) at joint B. The beam carries a concentrated load of 2750 lb at the end joint D. (a) determine the minimum diameter of the bolt at B if the shearing stress in the bolt is not to exceed 14000 psi. (b) determine the minimum diameter of the bolt at B if the allowable bearing stress in the bar plate is 20000 psi. Detail of joint B 3 ft (O с A 5 ft O B 6 ft D 2750 lb 3.75 in 3.75 in 0 in 0.80 Strut AB Beam CD (b Xh) Bolt (dmin) -0.50 in
1. Given the values of the load L and dimension R, for what value of the couple M will the force in link CH be equal to 10 kN, compressive? Note that R = 2m and L = 50 kN. FR R -R D C в м А F G E to -R- - 2R Given: (figure); R = 2m, L = 50kN Required: M so that FCh = 10 kN,C