4-43 The center post B of the assembly has an originallength of 124.7 mm, whereas posts A and C have a length of125 mm. If the caps on the top and bottom can be consid-ered rigid, determine the average normal stress in each post.The posts are made of aluminum and have a cross-sectionalarea of 400 mm². Eal = 70 GPa.A100 mm-B100 mm-C800 kN/m125 mm11800800 kN/m

The normal stress at A(&C) and B is 189.315 MPa and 21.3675 MPa, respectively.Explanation:From…

Answered: 4-43 The center post B of the assembly…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

2. For the truss shown below, determine the stress in members AC and BD. The cross-sectional area of each member is 850mm². [94.12, 78.42 MPa] A 000 RA B 70kN E 4 panels at 4m 16m = G 30kN H RH 3m
The solid cylinders AB and BC are bonded together at B and are attached to fixed supports at A and C. Knowing that the modulus of rigidity is 3.7E6 psi for aluminum and 5.6E6 psi for brass, determine the maximum shearing stress in cylinder AB And cylinder BC in ksi. 1 Aluminum T= 19.6 kip-in. Brass A - 1.4 in. B <-2.1 in. C 10 in. 15 in.
Determine the smallest safe cross-sectional areas of members CD, Cl and CH for the truss shown. The allowable stress are 100 MPa in tension and 80 MPa in compression. Indicate tension or compression. (Draw the required FBD and answer in mm2). Fa a –– a→– a- B D |E A a F G H а 3 2 т 45 kN
Two vertical forces are applied to a beam of the cross section shown in Fig.2. Determine the maximum tensile and compressive stresses in portion BC of the beam.(Take R=h=25mm). 4 kN 4KN -le A What B 300 mm 300 mm
Direct Stress Bronze Aluminum Steel A = 0.75 in.2 A = 1.0 in.? A = 0.5 in.? 3P 2F P 4P- -3 ft→ 5 ft 4 ft- 2. Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. Find the largest safe value of P if the working stresses are 120 MPa for steel, 68 MPa for aluminum, and 110 MPa for bronze.
QUESTION 2 The C83400-red-brass rod AB and 2014-T6- aluminum rod BC are joined at the collar B and fixed connected at their ends If there is no load in the members when T1 = 50'F, determine the average normal stress in each member when T2 = 120°F Also, how far will the collar be displaced? The cross-sectional area of each member is 1.75 in? 3 ft 2 ft
Determine the normal stress in members BD, AC, and BC in the truss shown. The crosssectional area of each member is 1500 mm2. Indicate whether the stresses are tensile (T) or compressive (C)
FIGORE %3D aluminum [E = 70 GPa] links (1) and H.W.3: In Figure (2) support rigid beam ABC. Link (1) has a cross-sectional area of 300mm2, and link (2) has a cross-sectional area of 450 mm2. For an applied load of P = 55 kN, determine the rigid beam deflection tad Nadhon hub at point B. (2) 4,000 mm (1) 2,500 mm 1,400 mm 800 mm P. FIGURE
-5 @ 3m-15m- C F H J K ML boo I A 4@4m=16m B D G E 60 kips A For the truss shown, what is the force in member FG? B what is the force in member BE? + --D
Problem 5: The compound bar carries the axial forces P and 2P. Find the maximum allowable value of P if the working stresses are 40 ksi for steel and 20 ksi for alumi- num, and the total elongation of the bar is not to exceed 0.2 in. 3 ft 4 ft 2P Aluminum A = 0.6 in.² E = 10 × 106 psi Steel A = 0.4 in.2 E = 29 × 106 psi
Determine the force P necessary to close the gap at the steel post. The steel post is 2 inch x 2 inch square and 8 in high. The aluminum alloy bar is 1.5 inch wide by 1 inch thick and 20 in long. The horizontal bar is considered rigid as are the loading caps at the steel post. The modulus of elasticity for the steel is 30,000 ksi, that of aluminum is 10,000 ksi. The yield stress for the steel is 36 ksi, that of the aluminum is 40 ksi. 8" 10" Steel 10" Rigid Aluminum 20 inches long * P 10" Gap = 0.02 inches
For the truss shown, calculate the stress in area of each member BD. The cross-sectional member is 1200mm². 4m B 6m U 3m 4m E 3m 100KN 200KN F M FLSNI

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS