The jib crane is supported by a pin at C and rod AB. The rod can withstand a maximum tension of 40 kN. If the load has a mass of 2 Mg, with its center of mass located at G, determine its maximum allowable distance x and the corresponding horizontal and vertical components of reaction at C.

The jib crane is supported by a pin at C and rod AB. The rod can withstand a maximum tension of 40 kN. If the load has a mass of 2 Mg, with its center of mass located at G, determine its maximum allowable distance x and the corresponding horizontal and vertical components of reaction at C.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter5: Three-dimensional Equilibrium

Section: Chapter Questions

Problem 5.42P: The 350-lb homogeneous plate has the shape of an isosceles triangle. The plate is supported by a...

See similar textbooks

Related questions

Q: As shown below, a sign weighing 434 N is hanging (via a wire) from a uniform 480 N beam of length L.…

Q: a) What is the magnitude of the minimum force of static friction required to hold both blocks at…

Q: The 15.8-in.spring is compressed to a 6.0-in. length, where it is released from rest and accelerates…

Q: Set P₁ = 7 kN, P₂ = 8 kN . (Figure 1) Figure 4m B E 4m 4 m 6 m D

Q: Initially contains Air: P1 = 30 lbf/in^2 T1 = 540 °F V1 = 4 ft^3 Second phase of process involving…

A: Given Initial Pressure, P1 = 30 lbf/in2 = 206.8 kPa Volume, V1 = 4 ft3 = 0.113 m3 Final…

Q: 1. Where controlling the angularity of a feature of size, the feature control frame is associated…

A: Filling the blanks

Q: What is the answer in #3B. Show complete solution and FBD

Q: NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to…

Q: Q2: A circular rod of 20 mm diameter and 100 mm length, is subjected to 2.5 KN tensile load if the…

Q: The rotation of the 3ft arm OA about O is defined by the relation θ=0.15t2, where θ is in radians…

Q: calculate the beanding moment and shear force diagrams

Q: A marksman fires a practice round from A toward a target B. If the target diameter is 160 mm and the…

Q: Initially contains Air: P1 = 30 lbf/in^2 T1 = 540 °F V1 = 4 ft^3 Second phase of process involving…

A: Given Initial Pressure, P1 = 30 lbf/in2 = 206.8 kPa Volume, V1 = 4 ft3 = 0.113 m3 Final…

Q: A differential manometer is connected at the two points A and B of two pipes as shown in the figure.…

Q: 2. Determine the possible range for R is the equivalent spring stiffness constant varies from 50 N/m…

Q: 3. A particle with a mass of 3 kg has velocity = 51 + 7j - 3km/s. The total force acting on the…

Q: A roofer tosses a small tool to the ground. What minimum magnitude vo of horizontal velocity is…

A: Given data: hAB=1.3+0.9=2.2 mhBC=4.1 m Need to determine the minimum magnitude of the horizontal…

Q: 20 lb/ft -8 ft- B . H O 8 ft G D F -8 ft 8 ft 8 ft- E A) Find equivalent forces at the joints for…

Q: The clearance hole LMC diameter formula is H @ LMC = O (H+H head) / 4 O (FF head) / 2 O (F+ F head)…

A: given; clearance hoe LMC diameter formula is H@LMC=?

Q: Problem 2. (Determining Cutting Speeds in Machining Economics) A turning operation is performed with…

A: Given: n=0.12 ; C=60 m/min Length of workpiece→L=450 mm Diameter of the workpiece→D=80 mm…

Q: Determine the following spring stiffness constant

Q: The bracket which is fastened to a wall by anchor bolts at A and B is loaded by the forces P=120N…

Q: For the next cable support (orange). Which of the following statements are true? a. Cable,…

Q: Knowing that the allowable normal stress for the steel used is 174 MPa, determine the section…

A: Givenσallowable=174MPa

Q: The rectangular coordinates of a particle which moves with curvilinear motion are given by x = 9.75t…

Q: A particle moves along the x axis from x; to xf. Of the following values of the initial and final…

A: Given, Particle moves along x axis from Xi to Xf

Q: A solid circular shaft of a diameter 100 mm is subjected to an axial stress of It is further…

A: Given data:diameter of the circular shaft, d=100 mmAxial stress of shaft, σ=50 MPATorque on the…

Q: If an object has a mass of 22 kg at sea level, a.) what will be its weight at a point where the…

A: Given data:- Mass of an object =22 kg and g=9.81 m/s2 To find:- Weight of an object Mass at that…

Q: . Find the member forces of members AF, FB, and AB using method of joints . Find the member forces…

Q: A car is moving on a curved horizontal road of radius 100 m with a speed of 20 m/s. The rotating…

Q: A pitot-static tube is used with a mercury (SGHg =13.6) manometer to measure the flow of an inviscid…

Q: Given: The plate( The shaded rectangular volume) has weighs 240 lbf. It is. suspended by able CD,…

A: Given: To find: Tension in cable CD

Q: Initially contains Air: P1 = 30 lbf/in^2 T1 = 540 °F V1 = 4 ft^3 Second phase of process involving…

A: Given data: P1=30 lbf/in2=206.843 kPaT1=540°F=555.372 KV1=4 ft3=0.113267 m3P2=20 lbf/in2=137.895…

Q: The system shown in the figure has a weight of 2928 N whose weight acts at point G shown in the…

Q: 8000 lb D tur 4000 lb B 5000 lb H 9ft 9ft 9 ft 9ft 9ft-9ft 12 ft

Q: A marksman fires a practice round from A toward a target B. If the target diameter is 170 mm and the…

Q: SOLVE STEP BY STEP IN DIGITAL FORMAT The three vertical, thin and homogeneous cylinders of the…

Q: Which three of the following are names given to the three regions in the typical wear growth curve:…

Q: Q1: i. Define and explain the following terms with appropriate examples and graphs. a. Sensitivity…

A: Q.1 (a) Sensitivity drift: The change in the instrument's sensitivity of measurement due to change…

Q: 7. Calculate the minimum wall thickness between the inside diameter and datum feature B shown in the…

A: The wall thickness equals half of the difference in diameters is 0.46

Q: Cords are loop around a small spacer separating two cylinders each weighing 400 kg and pass, as…

A: Given Number of cylinders = 2 weight of each cylinder = 400 kg weight due to both the cylinders =…

Q: Draw a different configuration, and make it a diagram similar to Fig. 3. Specify each mass and angle…

Q: Determine the horizontal displacement at A. Take E = 29(10³) ksi. The moment of inertia of each…

A: Given Data The universal distributed load is: w=2 k/ft The length AB is: AB=10 ft The distance AD…

Q: - A 12-ft wooden beam weighting 120 lb is supported by a pin and a bracket a A and by cable BC. Find…

Q: m 0000000000 m compressed spring of negligible mass llllllllll m

A: Given,

Q: cant read and i think you need t solve for fn and ft

Q: The 50-lb rectangular access door is held in the 90° open position by the single prop CD. Determine…

A: Here G represents the center of gravity Following data is provided Weight of the door W=50 lb a=26…

Q: A roofer tosses a small tool to the ground. What minimum magnitude vo of horizontal velocity is…

A: During free fall of the object, its horizontal velocity remains constant during its motion because…

Q: Problem 08.034 - DEPENDENT MULTI-PART PROBLEM - ASSIGN ALL PARTS - Refrigerant Constant Pressure…

Q: A column has a rectangular cross-section of 10mm x 20mm and a length of 1m. The slenderness ratio of…

A: given data:Cross-sectional dimension is 10 mm×20 mm,Length of the column is 1 m,

Question

The jib crane is supported by a pin at C and rod AB. The rod can withstand a maximum tension of
40 kN. If the load has a mass of 2 Mg, with its center of mass located at G, determine its maximum
allowable distance x and the corresponding horizontal and vertical components of reaction at C.
3.2 m
A
C
4 m
0.2 m
X
B
D
G

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The three bars are welded together to form a rigid unit that is supported by three slider bearings. Neglecting the weights of the bars, determine the magnitudes of the three bearing reactions caused by the 120-lbin. couple.
The homogeneous 240-lb bar is supported by a rough horizontal surface at A, a smooth vertical surface at B, and the cable BC. Draw the FBD of the bar and count the unknowns.
Q.2) The windlass is supported by a thrust bearing at A and a smooth journal bearing at B, which are properly aligned on the shaft. Determine the magnitude of the vertical force P that must be applied to the handle to maintain the equilibrium of the 100kg bucket. Also, calculate the reactions at the bearings. Since the bearings at A and B are aligned correctly, only force reactions occur at these supports. 0.3 m 981 N 0.5 m 0.1 m By 0.4 m B 30% 0.3 cos 30°m X 0.3 m G 0.5 m 0.1 m 0.1 m X 100 kg 0.3 m 30% 0.3 m
Solve the given problems. 2. The light right-angle boom which supports the 4KN cylinder is supported by the three cables and a ball-and-socket at O attached to the vertical x-y surface. Determine the reactions at O and the cable tensions. y 1.2m 1.5 m A ✓ I C F 0.75 m 0.75 m B 2.2m E D 1 m 1 m
The 480-kg uniform beam is subjected to the three external loads shown. Compute the reactions at the support point O. Thex-y plane is vertical. Positive values are to the right, up, and counterclockwise. 16 kN-m 3.7 KN 0 B 7.4 kN 1.3 m- 1.8 m Answers: Ox- Oy - Mo- 333 kN kN 1.8 m kN-m
The asymmetric simple truss is loaded as shown. Determine the reactions at A and D. Neglect the weight of the structure compared with the applied loads. Is the knowledge of the size of the structure necessary? 3.04 L, 3. 60 L 3.40 L, 3. 06 L 4.03 L, 6.03 L 4.30 L, 6.30 L
The 470-kg uniform beam is subjected to the three external loads shown. Compute the reactions at the support point O. The x-y plane is vertical. Positive values are to the right, up, and counterclockwise. 15 kN m 38 3.6 kN A B Höy 2.6 KN 1.3 m 2.0 m 2.0 m Answers: i 3 i Mo- kN KN kN-m
The hoist consists of a single rope and an arrangement of frictionless pulleys as shown. If the angle 0 = 33°, determine the force that must be applied to the rope, Frope, to lift a load of 4.7 kN. The three- pulley and hook assembly at the center of the system has a mass of 28.5 kg with a center of mass that lies on the line of action of the force applied to the hook. cc 130 BY NC SA 2013 Michael Swanbom Note the figure may not be to scale. Frope KN B A Fhook Frope
Determine the reaction at the support A of the frame. Supply the answer in kips (1000 lbs). 5 kip 7 kip 10 kip 2 kip -6 ft- -8 ft -6 ft- 8 ft -0.5 kip 6 ft
Determine the internal normal force at point F in the frame. The crate weighs 151 lb. 4 ft 1.5 ft 1.5 ft 1.5 ft 1.5 ft O B F C E D 0.4 ft
24. The 30-lb homogeneous bar AB supports the 60-lb block. The ends of the bar rest on 30 lb 60 Ib B frictionless inclines. Determine 12 ft 30 the distance x for which the 60 bar will be in equilibrium in the position shown. Answer: 10.5 ft Figure SP-3.18
When holding the equilibrium, the humorous H, assumed to be smooth, exerts normal forces Fc and FA on 6- 15-lb stone in the radius C and ulna A as shown. Determine B these forces and the force Fg that the biceps B exerts on the radius for equilibrium. The stone has a center of mass at G. Neglect the weight of the arm. H FB 75° Fo 0.8 in. FA 2 in. 14 in.